Search Documents

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By Paul L. Russell

Because of the increasing demand for fluorspar , investigation of the deposits of the Gila district in Grant County , New Mexico , was undertaken by the Bureau of Mines in 1943 with the cooperation of the Federal Geological Survey . It was the purpose of the investigation to assist owners and lessees to develop their properties and to attempt to estimate ore reserves that might be available to supply a 300- ton mill that was under construction at Gila . Field work was begun June 14 , 1943 , and ceased August 16 , 1943. Seven veins were trenched and sampled .

Feb 1, 1947

By N. S. Dalal, B. Jafari, X. Shi, M. M. Suryan

"It is well known that prevalence and severity of coal worker's pneumoconiosis (CWP) differ markedly in different regions and mines despite comparable exposures. These variations in the pathogenicity of different coal mine dusts can only partially be explained by the mineral composition of the coal mine dust and the rank of coal. Laboratory studies also do not correlate with the human experience. One major difference between human exposure and laboratory studies is that the coal miner breathes dust from freshly broken coal, while the animals or cells are exposed to stale dust. In an effort to find biochemical clues for resolving this apparent paradox, we have carried experiments to detect differences in chemical reactivities of fresh versus stale coal dust from several U.S. coal mines. Electron spin resonance (ESR) was used as a technique for the direct detection of the concentration and reactivity of free radicals. ESR measurements of freshly ground coal dusts of different ranks and composition showed significant differences in the amount and reactivities of the organic free radicals produced. The half-lives and reactivity patterns of these newly formed species of free radicals seem to correlate with the expected toxicity and pathogenicity of the dust, thereby, providing new clues to the biochemical mechanisms and pathogenesis of CWP. Similar detection of free radicals in freshly crushed quartz suggest that free radicals might play a significant role in the pathogenicity of quartz in causing fibrosis and eventually silicosis.IntroductionThe pathogenesis of coal workers' pneumoconiosis (CWP) has been an important topic of concern for decades, but the mechanism of CWP is still not understood. It is well known, for example, that the prevalence and severity of CWP differ markedly in different regions and mines despite com¬parable exposure'(1,2) but these observations can only par¬tially be explained by differences in mineral composition and rank of coal (3-5) Specifically, while epidemiological studies of coal miners indicate (1,2) that the effectiveness of coal in producing CWP correlates roughly with the rank (i.e. %,carbon content) of coal, such correlation has not been established via biological studies.(4-6)"

Mar 1, 1989

By R. J. Seibel

A statistical comparison of the dust exposures of coal miners with identical occupations in Pittsburgh, Pocahontas, Freeport, and Kittanning seams was conducted. Results indicated that, in some cases, identical occupations have different dust exposures in different seams. For example, the continuous miner operator in the Pittsburgh and Pocahontas seams is exposed to more dust than the same man in the Kittanning seam, but the Kittanning seam has more dust along the haulage roads than the other seams. Also, average dust exposures for similar occupations in continuous and conventional mining operations are similar.

Jan 1, 1974

By R. C. Hickman

"INTRODUCTION .As part of its spot drilling program, the Bureau of Mines core-drilled seven holes on the Alexander and Barber properties in Spartanburg County, S. C.Extensive surface float and outcrops of sillimanite schist on these properties appeared to justify drilling, which did not prove satisfactory, however, owing to the spotty occurrence of the schist bodies and the poor core recovery in the decomposed schist.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.This project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Alexander and. Barber properties are in the southern part of Spartanburg County, S. C. The Alexander property is about 5 miles cast of Woodruff. It is reached from Woodruff by driving east 5 miles on a macadam road to the intersection with an unsurfaced road near Unity Church. The farm house on the property is 0.4 mile north on this road. The sillimanite outcrop is in a field approximately 1,200 feet east of the farm house. The Barber property is about 2 miles north along the unsurfaced road that passes the Alexander property."

Sep 1, 1947

By John P. Harmon

Vehicles traveling on untreated dirt and gravel roads at open-pit mines disseminate high concentrations of dust (fig. 1). Excessive dust creates safety hazards by reducing visibility and may endanger the health of the men who breathe it. If the dust contains free silica, it can cause silicosis. In addition, maintenance costs of mechanical equipment are increased if equipment is operated in extremely dusty places. Dust on haulage roads in hot, arid country can be controlled if the surface of the road is sprinkled frequently and adequately with water. Often, when roads are sprinkled with water to control the dust, hazards are caused through reduced traction and skidding because of the mud that is formed on the surface of the road. Reducing the amount of water used will help to reduce the hazard of skidding.

Jan 1, 1957

By M. H. Kline

The Chestatee mine is one of several well known pyrite deposits in Georgia that are reputed to carry appreciable quantities of copper with the ore. The deposit is? in Lumpkin County on the Chestatee River, 6 miles northeast of Dahlonega (fig. 1). Old records and reports indicated the probable existence of an extensive unmined ore body, but the mine is inaccessible at present. The Bureau of Mines, after studying old maps and records, decided to cor8-drill along the strike of the lense beyond the limits of the indicated old workings in an attempt to extend the possible reserves. The advantageous location of the property indicates that it could become an economic source of pyrite to be used for the manufacture of sulfuric acid. Iron sinter resulting from the roasting of the ores could be sold at a premium in the Birmingham, Ala., area, and the copper content could be extracted to help replace the nation&apos;s depleted resources of this metal.

Jan 1, 1949

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the &apos;indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Will H. Coghill, G. Dale Cole

"INTRODUCTION This paper describes a method for the rational sorting of particles by means of a laboratory batch jig. Its purpose is to show that a material can be reliably appraised for gravity concentration without the drudgery of sink-float fractionations.Development of the batch- jig method of testing was incidental to a study of the Birmingham, Ala., red-iron ores now being conducted by the Bureau of Mines in cooperation with the University of Alabama and the ore-producing companies.APPLICATIONOres and coal are commonly tested for their gravity-concentration characteristics by specific-gravity dissections in heavy liquids. The heavy liquid most commonly used for coal is zinc chloride and for ores they are benzene, carbon tetrachloride, acetylene tetrabromide, methylene iodide, and thallium malonate formate. The last is poisonous and corrosive to the skin but is essential for separations in the 3.3 to 4.4 specific gravity range. The last two of these liquids are expensive, and several of them are hard to obtain now.Although it is not suggested that heavy-liquid dissections be eliminated entirely, sometimes a more reliable evaluation of coal and ore can be obtained by other and more simple means. For example, sink-float data were unsatisfactory as a guide to commercial gravity concentration of a red-iron ore because they did not take into account the difference in particle shape of the hematite and gangue and the differences in true and apparent specific gravity of the hematite grains, some of which were porous. For this ore, the batch-jig method of testing herein discussed proved advantageous. Not Only did the batch-jig data give a truer picture of the concentration problem, but only about one-tenth the time of the conventional sink-float tests was required."

Jul 1, 1944

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By James E. Hill

TECHNOLOGY is best nurtured by a sympathetic climate that is a composite of many factors. Necessity is a highly motivating factor as illustrated by the abnormal surge of technologic development curing wartime. Other factors include appropriate timing, economic pressures, available personnel, and in some instances, legislative action. Problems of recent concern to mining technology have been the quality and quantity of available technical personnel and the possibilities of restrictive legislation. The quality and quantity of technically trained personnel may be inadequate to meet the rapidly increasing complexity of modern technology coupled with the growing demand for qualified personnel. The question of appropriate training was a subject for debate.2 The curriculum and methods of teaching have changed. Questions have been raised on the relationship of scientist and engineer, interdisciplinary versus specialized curriculum, undergraduate versus graduate training, and the place of the smaller schools versus the large university-research complexes that have developed at some universities. Various aspects of the subject of engineering education for the mining industry were discussed at the meeting on Mining and Mineral Engineering Manpower at the Michigan College of Mining and Technology, November 18-19, 1963. Meanwhile, the trend toward interdisciplinary training gathers momentum as illustrated by the establishment of the School of Engineering Science at Johns Hopkins, the Schools of Engineering and Applied Science at Columbia, Princeton, and Yale, the Division of Engineering and Applied Physics at Harvard and, more recently, the School of Engineering Science at Florida State University which cuts across the conventional areas of civil, mechanical, electrical, and chemical engineering.

Jan 1, 1964

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By Robert W. Smith

Computation of the thermodynamic properties of the reaction products in the deflagration of explosive gas mixtures has been a most valuable guide regarding the possible kinetic mechanisms of homogeneous combustion processes. Knowledge of the physically possible end states is indispensable for understanding observed deviations from equilibrium in heterogeneous combustion. However such information on dust flames is entirely lacking. To complement a Federal Bureau of Mines study of stationary graphite dust flames burning in pure oxygen,6/ this report gives examples, at atmospheric pressure and room temperature, of composition profiles in an idealized oxygen-dust flame, with both mass and enthalpy being preserved. Similar profiles can be obtained from the data of the paper for elevated temperature and pressure.

Jan 1, 1960