Search Documents

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By John R. Benham

The Long Swamp RARE II area contains no prospects, claims, or mines. It has a low potential for ore deposits. There are no geothermal, oil, or gas leases in the area. APPRAISAL There are no mining districts in the study area. The nearest is Chewack Mining District, which is 6 mi (9.6 km) north of the area. This district had numerous claims located for tungsten; the principal tungsten ore mineral was wolframite. Wolframite was found here in 1898 by surveyors of the International Boundary Commission. The area was staked in 1908 and developed during 1915 and 1916. Only in 1936 was ore shipped; the 30 ton (27.2 t) shipment proved to be unprofitable for the claimants (Culver, 1945, p. 41).

Jan 1, 1982

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By R. V. Ramani, C. B. Manula, A. Owili-Eger

• MINE VENTILATION NETWORK PROBLEM (NATURAL SPLITTING; FIXED • QUANTITY BRANCHES; METHANE SIMULATION; NETWORK TOPOLOGY REVISION; • ABSOLUTE PRESSURE) • NFIXB = NO. OF FIXED QUANTITY BRANCHES • DD(I) = AIR QUANTITY ASSIGNED TO FIXED QUANTITY BRANCH I, IN KCFP • NFBPF = NO. OF FIXED QUANTITY BRANCHES PLUS FAN • NFBPFG = NO. OF FIXED QUANTITY BRANCHES PLUS FAN PLUS METHANE • EMISSION BRANCHES • NBWNVP = NO. OF BRANCHES WITH NATURAL.VENTILATION PRESSURE • NVP(I) = NATURAL VENTILATION PRESSURE ASSOCIATED WITH • THE I-TH BRANCH • NF = NUMBER OF FANS • NB = NUMBER OF BRANCHES • MAXIT = MAXIMUM NUMBER OF ITERATIONS • MAXJ = MAXIMUM NUMBER OF JUNCTIONS • NJ = NUMBER OF JUNCTIONS INVOLVED IN THE SOLUTION * NM = NUMBER OF MESHES • NP = NO. OF POINTS TO DESIGNATE FAN CHARACTERISTIC * Q = QUANTITY OF AIR FLOW IN KCFM • R = RESISTANCE OF AN AIRWAY • WIDTH = AIRWAY DIMENSION • LENGTH = AIRWAY DIMENSION • HEIGHT = AIRWAY DIMENSION • SUMNVP = SUMMATION OF NATURAL VENTILATION PRESSURE FOR ANY MESH • X (I) = QUANTITY OF AIR, IN KCFM, ASSOCIATED WITH THE I-TB POINT • ON A FAN CHARACTERISTIC • E = ERROR FOR CONVERGENCE • FF = FRICTION FACTOR • FX(I) = FAN PRESSURE, INS INCHES OF WATER GAGE, CORRESPONDING • • TO A QUANTITY X(I) • H = HEAD LOSS IN INCHES OF WATER GAGE • I = BRANCH NUMBER • J, J1, J2 = JUNCTION, J1 AND J2 ARE TWO NODES WHICH DEFINE A • BRANCH • KEY = NO. WHICH SIGNALS THE TYPE OF FAN CHARACTERISTIC TO BE • EXPECTED

Jan 1, 1975

By Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressures. New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 2010

By D. Harrington

In this period of generally increasing taxes of various kinds, one hears less complaint by mining companies about the high cost of workmen's accident compensation than was the case a few years ago, the reason perhaps being that other and more pressing phases of the tax problem now over shadow the heavy expenditures for compensation premiums which a few years ago were considered a severe burden on the mining industry. Nevertheless, the financial expenditures of the mining industry in higher compensation benefits and hospitalization or in higher premium rates, or both, instead of being less have actually increased in many States in the past year. In the spring of 1937, proposals for increased benefits to injured employees in compensation, hospitalization, or medical aid were actively before legislatures in California, Connecticut, Georgia, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Massachusetts, Michigan, Minnesota, New Mexico, Oregon, Pennsylvania, South Carolina, Texas, Utah, Washington, Wyoming, and possibly other States. In some cases, the proposed increases in benefits were so much greater than expenditures for similar items in the past that premium rates per $100 of payroll would almost certainly rise sharply. At this same time, occupational-disease-compensation coverage also was under consideration by legislatures in Arkansas, California, Delaware, Idaho, Indiana, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah, and Washington. Sooner or later (and probably within the next few years) occupational-disease compensation will be accorded practically as wide recognition as accident compensation receives at present, and, unquestionably, mining in all of its branches will be affected more or less drastically. Hence, the present outlook is that the mining industry, in company with practically all other industrial activities, will be confronted by materially higher compensation costs than those of the past or the present, to which rather violent exception has been taken, at least in some States and at some times.

Jan 1, 1938

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By L. G. Austin

"This paper is based on the development of the Maza-Austin technique for characterizing thousands of coal particles by approximate analysis of the major inorganic constituents Ca, Al, Si, K, Na, Fe and S in each particle. The technique has sufficient sensitivity to work on small volumes, is fast enough to handle large number of particles within a reasonable period of time, and consists of scanning electron microscopy combined with energy dispersive x-ray spectrometry (SEK-EDS). A computerized SEK-EDS system that allows the automated analysis of hundreds of coal particles per hour' is described. The analysis is based on the location and tracing of coal particles embedded in a polished specimen, the selection of sampling points on the traced particles, the collection of an x-ray spectrum from each sampled point for a defined period of time, and the processing of the x-ray intensity to calculate point composition using ZAF corrections. Procedures for correcting for dead time, background, detector efficiency and spectrum overlap are described. These corrections are essential if reasonably accurate analyses are to be obtained from unknown complex mixtures of the elements in a coal or fly ash particle. Examples are given. INTRODUCTION Coal is a complex mixture of organic and inorganic materials. The inorganic fraction is referred to as mineral matter (Gluskoter, 1978) but can occur in three modes: (i) an observable mineral species; (ii) as cations held by ion exchange to carboxylic groups; and (iii) in chelate complexes. The mineral matter content normally represents a significant proportion of a coal, with an average value of about 15% for US coals (Gluskoter, 1975). The standard methods of analysis of the mineral matter in coals are performed on a sample selected to represent the whole coal as closely as possible, and give the overall inorganic composition in the coal. Such analyses are of limited use for solving problems originating from the behavior of individual coal particles, whose compositions vary widely from the average value. This is particularly true in pulverized coal combustion, where the current methods of predicting the slagging and ·fouling potential of a coal are based on the bulk ash composition, but the fly ash particles which create the deposits originate from coal particles with large differences in mineral compo1ition. Some examples can be found where, in a comparison between two coals, the one with the smaller slagging potential according to the mean ash composition was the one that behaved worst in the furnace (Moza et al., 1980; Koza and Austin, 1983). The u1e of gravity fractionation to assess the slagging potential of pulverized coals has shown that conventional ASTM analysis is not sensitive to differences in the distribution of mineral matter when comparing coals (Borio and Narciso, 1979). Bryer (1979) concluded that coals should be examined for fouling and slagging potential by analyzing gravimetric and size-fractionated coal, preferably pulverized· and ground to the size expected at the mill outlet."

Jan 1, 1989

By A. L. Engel

Included in the program of the Rare and Precious Metals Station, Metallurgical Division, Bureau of Mines at Reno, Nev., are investigations of treatment methods for ores representative of various mining districts throughout the country. The samples received for this work may come from areas only recently explored or from newly discovered ore deposits in older mining districts. The present investigation deals with a case of the latter type, the. ample having come from a section that has a past record of considerable precious. metals production. The application of current treatment methods to this type of ore seems to offer excellent possibilities of satisfactory economic results. Definite identification of the silver mineral in this ore asthe chloride cerargyrite, AgCl, adds considerable interest to, the investigation, as in many cases where silver occurs in comparatively small amounts in an ore it is not possible to identify the particular mineral carrying the silver or else it is contained in or combined with other more common minerals. Cerargyrite is the "horn silver" of the bananza period and is mentioned in many accounts of pioneer mining of high-grade ores The occurrence of this mineral in finely disseminated form it a low-grade ore is believed to be unusual. The sample investigated was obtained from the' Bullfrog District neat Beatty, southwest Nye County, Nevada. The ore contained 16.7 ounces of silver per ton of ore, 0.007 ounce gold, and 0.32 percent copper in a silicious gangue, with accessory minerals, including iron oxides and scorodite; the hydrous iron arsenate.

Jan 1, 1949

By J. W. Faul

[The Bureau of Mines initiated an extensive research on coal-mine ventilation factors in 1922, large- scale tests being conducted in its experimental nine near Bruceton, Pa., over a period of two years. A comprehensive report an this work is in course of preparation, but in order to place the practical results before the mining fraternity immediately and in condenses form, the more important features will be presented in a number of short papers. The present report is the first of a series dealing with the resistance of coal-mine entries to the flow of air and considers only entries in which there are no obstructions other than the natural roughness of the ribs, roof, and floor.]

Jan 1, 1924

By NIOSH Publications

In 2004, 14,478 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (48.9%) were sand and gravel mines, followed by stone mines (30.4%), coal mines (13.9%), nonmetal mines (5.1%), and metal mines (1.7%).

Sep 1, 2007

By Spencer P. Howell, Munroem Charles E.

"Introduction;As in the case of TNT previously presented*, this report presents the results of an investigation to discover the safest and best way of utilizing picric acid for industrial blasting purposes. It describes the physical and chemical properties of this explosive, gives precautions to be observed in handling, packing, preparation of cartridges, and holes, presents the results of field tests in blasting stumps and bowlders, and compares the results with those obtained from dynamite.The investigations reported herein were undertaken and this paper has been prepared, solely to aid in the salvage of the surplus picric acid accumulated for war uses and released by the declaration of the armistice. No funds were available nor have any been appropriated with which to defray the expense of converting this picric acid into any other form or to prepare any explosive mixture from it. The sole problem was to find appropriate uses for this military picric acid in existing needs and to show that it can be efficiently used in carrying out essential civil projects.It is not intended by this publication to promote the use of picric acid as an industrial explosive further than is necessary for the proper utilization of this surplus. On the contrary, the authors believe that picric acid by itself is unlikely to come into general use as an industrial explosive, chiefly because of its cost but also as shown by the clouds of smoke it emits on explosion and the nature of the reactions it undergoes because we do not obtain from it its highest efficiency. As demonstrated in its previous use in Joveite, better results and higher efficiencies may be obtained by mixing picric acid in proper proportions with sodium nitrate or ammonium nitrate, to more completely oxidize the picric acid, and another nitrosubstitution compound, such as nitronaphthalenes, with which do desensitize and waterproof the composition formed. By such admixture not only may the energy resident in the picric acid, be more fully utilized but the cost of the resulting blasting explosive should be much less than that of picric acid."

Apr 1, 1921

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By G. A. Brady

Seven samples of Pennsylvania anthracite from the Bottom Ross bed were analyzed and tested to obtain data on cleaning characteristics, proximate and ultimate analyses, specific gravity, grindability, heating value, and ash softening temperature. Ash content of the samples varied irregularly from 9.0 to 34.4 percent, the range being narrowed to an upper limit of 14.8 percent ash by removing impurities dense enough to sink in a medium with a specific gravity of 1.90. Ash content of the sink material with specific gravity greater than 1.90 ranged from 56.4 to 80.4 percent; corresponding specific gravities were 2.095 to 2.534. Volatile matter contents were indicated to be higher for the ash-forming minerals than for the pure coal substance in the various specific gravity fractions of a given sample. Specific gravities of anthracites with compa¬rable ash contents but from different locations in the bed varied as much as 0.06. The grindability index increased significantly with increasing ash con¬tent of specific gravity fractions from all the samples.

Jan 1, 1968

By Robert S. Sanford

This paper deals with truck haulage methods and costs at one of the many open-cut mines that are replacing rail haulage with heavy-duty trucks. At this mine, ore is trucked to a crushing plant, centrally located within one of the open-cuts. The requirements for efficient low-cost truck haulage are: Good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers The weighted average cost of hauling a long ton of ore to the crusher and the waste to the dump was reduced from $0.1993 in 1948 to $0.1114 during the last half of 1949, his corresponds to a cost per ton mile of $0.0864.

Jan 1, 1952

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

The purpose of Volume II of this study is to provide a general plan for the pilot testing of two materials which could be used to tag explosives for both pre- and postdetonation identification and of tracing techniques which would thereby aid the investigator of an unauthorized bombing or explosion in being able to determine the source and/or user of the explosives. Volume I described the planning factors by which the tagging of explosives could be implemented on a National basis. 1.2 BACKGROUND Tagging explosives at the time of manufacture with a taggant material that could survive detonation, be recovered, and provide an investigative lead has been seriously studied for several years. This concept has gained widespread support among many law enforcement groups because of the scant clues that can presently be found among bombing residue.

Jan 1, 1977

By M. F. Dunn

A handbook to provide a quick reference guide for selecting and using jet fans in a variety of conditions was prepared. The document is intended for use by front-line supervision, ventilation engineers, and mine planners. Included are discussions of jet fan characteristics, selection and use critieria, and do's and don't's for easier operation, safety, and performance. The handbook is based on research at three underground metal/nonmetal mines having cross-sectional areas of 900 to 2,000 ft2.

Jan 1, 1983