Search Documents

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By Radford Schantz

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA). San Bernardino County. California During field work. BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1.188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) fun access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion. $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By F. R. Cattoir, T. A. Sullivan

Commercial uranium metal was electrore fined to a high- purity product using molten- salt electrolytes in an inert atmosphere cell . Electrorefined uranium that contained , after consolidation , less than 30 ppm of metallic impurities was prepared . A method of leaching the electrolyte crystals to remove the salts was developed . Cathode current efficiencies from 90 to 100 percent were obtained . Two molten- salt electrolytes were prepared and evaluated : (1 ) lithium chloride - potassium chloride - uranium trichloride and ( 2 ) sodium chloridepotassium chloride - uranium trichloride . Very little difference was found in the purity of the uranium metal produced in either system . The lithium chloride - potassium chloride - uranium tri - chloride electrolyte was preferable from an operational standpoint .

Jan 1, 1964

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By Arthur L. Murray

"During recent months much criticism as to the efficiency of mine labor has been heard from various, sections of the country. No doubt much of this criticism has been well founded. The present lack of efficiency and of stability is due primarily to a spirit of restlessness and partial irresponsibility engendered during the transition from war conditions to peace time conditions. This spirit or unrest not only among the laboring classes but in every branch of the human family following a period of intense nervous tension in a nation appears to be a natural sequence of war and beyond the control of man. This condition will gradually disappear, and the majority of our people will again assume their natural order of living, but labor will for a considerable period be sensitive to these influences, whether they be exerted for good or for evil. Employers of labor should take cognizance of this fact and bend every effort towards the development of measures that promote efficiency and permanence of the working force.Labor efficiency depends upon many and varied factors. Some of these factors as applied to mine labor are briefly enumerated in the following paragraph:Selection and Placement of Manpower:In the selection of men the two main considerations are physical ability and adaptability. The laws of mechanics should be applied in the selection of men as in the selection of machinery. If a machine is required for a certain class of work, the type of machine known to be mechanically fit for such work is selected. Likewise, men should be selected with regard to their physical and temperamental fitness for the kind of work expected of them."

Apr 1, 1920

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By E. T. Bowers

The Accident Analysis (ADA) computer program was developed at the Spokane Research Center (SRC) to provide a rapid broad-based analysis of mining accidents. Because the Bureau of Mines often needs this type of information for the development of viable research programs the ADA program was written to access and analyze accident data available frog the Labor Department's Mine Safety and Health Administration (MSHA). This report describes the ADA program, the data it uses, and the potential value it has for planning mining research.

Jan 1, 1987

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the&apos; Bureau&apos;s laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By D. C. Fleck

The Bureau of Mines, in a cooperative research program with four lead companies, has investigated ferric chloride leaching of galena to prepare lead chloride for molten-salt electrowinning to produce lead metal. The hydrometallurgical-electrolytic process is an alternative to the sintering-smelting-refining process currently used to produce lead metal and avoids the environmental problems associated with a conventional smelter. During investigations on the electrowinning aspects of the work, it was noted that certain cations, moisture, and sulfate in the electrolyte affect lead metal purity, cell voltage, current efficiency, and viscosity of the electrolyte. Results of bench-scale tests are re-ported on the effects of CaCI2, CuCI2, FeCI2, MgCI2, NaCI, ZnCI2, PbS04, and moisture on electrolysis. As impurities increased in the electrolyte, current efficiency decreased. CaCI2, CuCI2, and FeC12 decreased current efficiency by 12 to 47 pct. ZnCl2 gave a small voltage increase, while CaCI2 addition equivalent to 4.9 pct Ca caused a 50-pet increase in voltage. The lead metal was contaminated in direct proportion to the CuCI2 buildup in the electrolyte, Anode corrosion was observed with MgCI2 and MgC12?6H20. Viscosity increased appreciably with the buildup of NaCI, CaCI2, and sulfate. Electrolyte foaming occurred with ZnC12, MgC12?6H20, MgC12, FeC12?2H20, and FeCI2. Moisture inhibited the coalescence of the lead metal.

Jan 1, 1983

By C. Van Dyke, K. Van Dyke, J. Gutierrez, C. Nowack

"Using propidium assay and flow cytometry, we examined how silica exerts its toxicity toward phagocytic cells employing the human neutrophil as a model. This toxicity appears to be associated with calcium bound to silica. Once the silica with calcium is phagocytized, the extra calcium causes the death of the cell. Using ""Ca we found that 6 to 10% of millimolar calcium is bound to milligram amounts of respirable-sized silica (diameter of 5 µ.m or less) at physiological pH. If the silica particles arc coated with an organosilanc (Prosil 28). calcium binding is decreased by 60% as is cell death. Pretreating with INDO IAM (a chelator of intracellular calcium) reduces the cellular death by 80%. Nonfibrogcnic particles- polystyrene beads or coal dust-produced 10% or less cell death in a 4-h period. Silica with no added, external calcium appears to exert toxicity to neutrophils; however, pretreating cells with EDT A decreases cellular death to the level of nonfibrogcnic particles. Chronic toxicity with silica-calcium appears similar to the chronic toxicity in gout where particles cause a cycle of inflammation. c 1993 Academic Press, Inc.Silicosis is an occupational disease caused by the inhalation of fine particles of silica, usually between 0.1 and 5 µ.m in diameter (1). A recent hypothesis explaining silica's toxicity suggested that surface free radicals caused damage to cells (2). This explanation appears doubtful, however, since the addition of silica to water, such as that found in biological systems, quenches free radicals; also, such a hypothesis does not provide basis for a persistent inflammatory pattern that lasts for years. Kane et al. (3) proposed that silica's toxicity resulted from an excessive concentration of calcium ions within the phagocytic cell (macrophages). However, the mechanism that was capable of linking silica to an excess of intracellular, ionic calcium was not explained. The surface of silica is certainly involved because covering the surface with polymers or phospholipids decreases silica's toxicity (4-6).When silica is engulfed by macrophages platelet activating factor and leukotrienes are produced (7, 8). This is the same inflammatory pattern produced by phagocytic cells exposed to the calcium ionophore A23187 and ionic calcium. How could silica be acting like A23187? Perhaps calcium binds to silica extracellulary and then is released intracellulary following phagocytosis; the latter process, in a sense a ""piggy back"" process, would permit activation of inflammation and cell death mechanisms."

Nov 1, 1995