Search Documents

By Leonard Obert

The various underground rooms in the Bureau of Mines Oil-Shale mine, Rifle, Colo., have been open for periods ranging from 3 to 5 years. During this time 3 roof falls have occurred; 1 was induced, and the other 2 were unintentional. The three roof falls are described in this report. Two causative factors are discussed -a time-dependent deterioration of the roof rock and an unfavorable system of jointing that occurred in the strata overlying the present roof horizon. Irrespective of cause, the operating life of any stoping area would have been short com-pared with the life of the roof (1 to 4 in the most unfavorable instance), if a high-production system of mining had been employed. The report is concluded with several recommendations that should be considered in planning future mining operations.

Jan 1, 1958

By L. A. Stewart

This is one of a series of reports prepared by the Federal Bureau of Mines on mining methods, performance, and costs at individual mines in the United States. The primary purpose of these papers is to promote development and conservation of our mineral resources by disseminating technological information on methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. This report discusses the highly selective mining methods of the Jaquays Mining Corp. at the Regal asbestos mine, 45 road miles northeast of Globe, Ariz. The milling method at the Globe plant is discussed briefly, and the extraction ratios of the various grades of fiber are tabulated. The proposed flowsheet of a new mill under construction is shown.

Jan 1, 1961

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By Hillary W. St. Clair

Reaction rate coefficients were determined from analyses of the effluent gas for the reduction of granular ferrous oxide to metallic iron by passing carbon monoxide through a packed bed of oxide at a controlled rate in the temperature range 1,000° to 1,300° C. Coefficients were determined by the comparison of observed analyses and calculated analyses using a mathematical model that takes into account the nonuniform composition of both the solid oxide and the gas. A method is also given for finding the value of the rate coefficient that best fits the observed data.

Jan 1, 1968

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine&apos;s airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By W. H. Rinkenbach, C. A. Taylor

"Among the recently patented detonating compounds that have been suggested as substitutes for the commonly used fulminate of mercury is the normal lead salt of trinitroresorcin, or styphnic acid. As no data concerning its use or practi¬cability were available, a study of its properties was made in the explosives laboratory at the Bureau of Mines experiment station at Pittsburgh, Pa. This paper embodies the results obtained.Normal lead trinitroresorcinate was first prepared and patented*** by Herz; it probably found some use during the World War, but no record of its performance is available,Preparation of Lead Trinitrpresorcinate.In his patent specifications, Herz states that the normal salt may be obtained in a quantitative way by precipitating a multiple of the equivalent weight of the lead salt of a strong inorganic acid - such as lead nitrate - in the presence of a weak organic acid - such as acetic acid - by heating with a Teak solution of the alkali-metal salts or alkaline-earth salts of trinitroresorcin. Herz gives the following example: 245 grams of dry trinitroresorcinand 290 grams of crystalline sodium carbonate are dissolved in in 18.8 liters of boiling water, to which 77 c.c. of glacial acetic acid is added. The toiling solution is mixed with a boiling solution of 650 grams of lead nitrate in 1.4 liters of water, stirring rapidly; and the mixture is boiled for two minutes, after which it is cooled quickly with constant stirring. The precipitated crystals are then filtered off, washed several times with cold water, and dried."

Oct 1, 1923

By Ellsworth Spencer

Noise induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A).(1) The focus of this research was to determine the noise exposures of heavy construction equipment operators while documenting the workers’ tasks, (i.e. hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were studied for this research located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25,836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1,397%.