Search Documents

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Feb 1, 2009

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By Bertrand L. Johnson

Pure talc is a hydrous magnesium silicate (Mg3Si4010(OH)2). Pyrophyllite, although it resemble: talc in certain physical properties and uses, is a hydrous aluminum silicate (Al2Si4010(OH)2) - like kaolin, except that kaolin has a somewhat different composition (Al2Si205(OH)4) and structure. Soapstone can be considered essentially an impure talc grid when pulverized is used for many of the same purposes as talc. Massive, compact varieties of talc often are called steatite. PROPERTIES Talc and pyrophyllite are characterizes; by their softness (hardness on Mohs' scale, 1) their greasy feel, pearly luster, white color, and perfect basal cleavage. They have similar crystal structures, and this similarity explains the close resemblance of the two minerals in physical acid chemical properties. Talc is a good electrical insulator, resists the action of most acids and alkalies, and has an exceptional heat-retaining capacity. Its specific gravity is about 2.7.

Jan 1, 1939

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase

Jan 1, 1937

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase of the iron and steel industry. Thus, for the first time, producers, buyers, sellers, and consumers of iron and steel scrap have had an accurate statistical picture of this important raw material As originally contemplated, the study was to be continued on an annual basis, but, owing to budgetary limitations for the fiscal year 1937-38, the Bureau may be unable to conduct the canvass for 1937.

Jan 1, 1937

By J. D. Kalasky, Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out- side headings of a set of five being developed in virgin area, and (2) conducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By Edward Kline

A review and synthesis of literature pertaining to biological consequences of submarine mine-tailings disposal (STD) was conducted. STD can result in massive sea floor sediment deposition. STD may also increase suspended sediment, trace metals, and residual milling reagents in receiving waters. These perturbations, which are highly site dependent, invariably smother benthic organisms, and could potentially affect or alter fish, plankton, and benthos through acute and chronic toxicity, bioaccumulation, behavioral changes, smothering, derived secondary effects, and habitat alteration. Much of the available information concerning STD is unpublished and limited to a restricted number of sites. From this information and related research, it appears that benthic smothering is the only major consequence of a properly designed STD system. There have been cases of metal bioaccumulation due to inadequate preliminary evaluation, Also, shallow water habitat alteration has resulted from STD. Reductions in biological production are likely due to benthic smothering. The rate of ecological recovery after termination of an STD operation varies and is difficult to assess, The consequences of STD are site specific. Additional research is needed concerning possible consequences of milling reagents and the broad implications of benthic smothering. Also, methodologies are needed to allow better prediction of benthic recolonization and ecological implications of metal bioaccumulation.

Jan 1, 1994

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By M. W. Price, Joseph V. Mather, E. H. McCleary

"INTRODUCTION The asphyxiation or poisoning of workmen in underground mines by noxious gases from blasting in adjacent strip mines can be prevented.Considerable progress has been made in eliminating or reducing hazards to the health and safety of underground workmen in anthracite mines, but seldom does a year pass without reported cases of underground workmen being poisoned by the fumes from blasts of explosives in strip-mining operations. In the early days of the anthracite industry, the coal near the surface was only partly mined, and many small stumps of pillars and barrier pillars were left standing; these pillars are now being recovered by stripping. It has become necessary to give more consideration to the effects of blasting at strip mines upon the quality of the air in underground mines adjacent to stripping operations.Special precautions are taken by the .personnel of the Jeddo-Highland Coal Co., whose mines are near Jeddo, Luzerne County, and near Centralia in Columbia and Schuylkill Counties in the anthracite region of Pennsylvania, to prevent asphyxiation of workmen by carbon monoxide or other toxic gases resulting from blasting in strip mines. The procedures established by the Jeddo-Highland Coal Co., are given in this circular so that others may benefit thereby and thus avoid hazards to underground workmen where mining is carried on under similar circumstances."

May 1, 1949

By D. E. Wolfson

The Bureau of Mines carbonized 35 coal samples from Logan and Mingo Counties) W. Va., at 900° C using the Bureau of Mines-American Gas Association method, and determined yields of products and physical properties of cokes. Twenty samples represented the No.5 Block, Stockton, Chilton, Cedar Grove, Lower Cedar Grove, Alma, No. 2 Gas, and Eagle beds in Logan County, and 15 samples represented the Coalburg, Buffalo Creek, Winifrede, Cedar Grove, Lower Cedar Grove, Alma, and No.2 Gas beds in Mingo County, W. Va, Chemical analyses were determined for all coals. All coals in both counties rank as high-volatile A bituminous. Most of the coals are chemically suitable for metallurgical coals. Coals with accept-able ash and sulfur contents can be used as major constituents in coking blends with higher rank coal to yield coke with satisfactory properties for blast furnace use.

Jan 1, 1967

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977