Search Documents

By J. E. Shelton

Flotation tests are described on samples of two lowgrade nickeliferous ores of Oregon and Washington. The sample from the Congress mine, Ferry County, Wash., contained 1.2 percent Ni, occurring chiefly as millerite. The sample from the Shamrock mine, Jackson County, Oreg., contained 2.20 percent Ni and 0.78 percent Cu occurring chiefly as pentlandite, nickeliferous pyrrhotite, and chalcopyrite. The millerite in the Congress ore was concentrated by flotatioin with aulfydric collectors in a series of locked tests to recover 73 percent of the nickel as a 7 percent bulk concentrate. By successively regrinding and floating the bulk concentrate, it was further concentrated to 12.4 percent Ni at a recovery of 59 percent and 21.8 percent Ni at a recovery of 50 percent. Attempts at selective concentration of the copper-nickel Shamrock ore were only partly successful because of the intimate association of pentlandite and chalcopyrite. The nickel concentrate, which contained 86 percent of the nickel, had an analysis of 4.42 percent Ni and 1.03 percent Cu. The copper concentrate had an analysis of 18.8 percent Cu and 1.96 percent Ni and contained 48.5 percent of the copper. A bulk sulfide concentrate contained 92 percent of the copper and 01 per¬cent of the nickel and had an analysis of 4.17 percent Ni and 1.63 percent Cu.

Jan 1, 1956

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By Edmund S. Leaver, Charles E. Van Barneveld

In response to numerous requests from metallurgists and operators for information regarding the status of the sulphur dioxide leaching process , developed at the Southwest experiment station of the U. S. Bureau of Mines , Tucson , Ariz . , the following statement has been prepared . A more complete report is now in course of publication and will appear as Technical Paper 312. This process was devised to provide a cheap and efficient method for treating the so- called "porphyry " copper ores of the Southwest which generally contain both " sulphide " and "nonsulphide " copper minerals , mixed in such proportions that they can only be satisfactorily treated by a method which will concurrently recover both the sulphide copper and the nonsulphide copper . The latter term has been adopted to include all the minerals commonly referred to in operating phraseology in the mills of the Southwest as " oxidized" , " oxide " , or " soluble " copper . confident that the sulphide dioxide leaching process , as developed by us with the cooperation of the Miami Copper Co. and the Arizona Copper Co. , is suitable and commercially available for a wide range of ores .

May 1, 1922

By Fremont F. Clarke

"INTRODUCTION Clay beds of southwestern North Dakota were investigated to determine (1) the average alumina content of the clays in four principal areas of occurrence, (2.) which, if any, would be the most feasible method of extracting alumina from the clays, and (3) whether the clays had any other commercial uses.During the investigation exposed sedimentary beds were examined for clay and the thickness and areal extent of outcropping clay beds in the more promising areas were measured. Four-principal areas of bentonitic clays, comprising 6,967 acres in Stark, Slope; and Billings Counties, N. Dak., were mapped and sampled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chiefs analyzes samples and makes beneficiation tests.Acknowledgment is duo John P. Gries, professor of geology, South Dakota School of Mines and Technology, for his studies of and advice on geological phases of the work. His data were drawn on freely in preparing this report; also E. D. Gardner, regional engineer, Rolla, Mo., and E. Y. Dougherty, district engineer, Rapid City, S. Dak., for assistance and advice in supervising the program."

Mar 1, 1948

By R. A. Cattell

With the activities of the Petroleum and Natural Gas Division geared chiefly to problems directly connected with the war effort , the emphasis of the work under oil and gas development and production was to make engineering studies of selected reservoirs for the Petroleum Administration for War , to determine the extractable quantities of components in them, and to study the characteristics of these components for use in the manufacture of aviation gasoline and other products . The needs of the Petroleum Administration for War and the operators for specific data from gas - condensate fields were fulfilled , and , in addition , engineering data along lines of a forward - looking program of research on reservoir behavior were collected , which should be of great value in the postwar period . It is planned to publish many of these data as soon as conditions permit . The work of the Secondary Recovery Section had as its objectives in- . creasing the rate of production of crude petroleum and , which is more important , preventing the premature abandonment of wells in " stripper " and marginal According to the National Survey of Stripper Wells by the National Stripper Well Association in cooperation with the Interstate Oil Compact Commission , a total of 67,460 stripper wells was abandoned from January 1 , 1935 , to July 1 , 1942 , inclusive , with an estimated loss in proved reserves of approximately 216 million barrels . This survey also indicates that over 1.2 billion barrels of oil would be recovered by primary production from more than 290,000 stripper wells then in operation , and an additional 2.5 billion barrels of oil could be recovered from them by secondary production methods . The work of the Chemistry and Refining Section was oriented towards the optimum utilization of crude oils in the manufacture of aviation fuels for spark-ignition and jet - propulsion engines . The work involved intensive studies of superfractionation , hydrocarbon analysis , and the engine testing of fuels . Particular attention was given to the effect of sulfur compounds in the crude oils and in the fuels made from them . The research on thermodynamics is concerned with the experimental determination of precise and accurate values of the fundamental thermodynamic constants of pure hydrocarbons and related compounds . The data obtained in these investigations will be utilized for devising and improving chemical processes in which petroleum hydrocarbons are the raw materials . Without such data , much time and expensive material and equipment may be wasted in attempts to obtain reactions under conditions that the laws of thermodynamics rule out of consideration . Thermodynamic data are useful and required in the petroleum industry for calculations of heat balances in the design of furnaces , fractionating towers , and heat- transfer equipment . It is of utmost importance , also , to know the heat requirements of cracking and other chemical reactions so that heat may be supplied or dissipated in the proper proportions . These needs for thermodynamic data are being recognized more and more by petroleum -refining engineers . The responsibility for the production of helium for the Navy , the Army , other governmental agencies and non-Federal users is vested in the Bureau of Mines by an Act of Congress ( 50 Stat . 885 ; 50 U.S.c. 161-166 ) . The Helium Subdivision of the Petroleum and Natural Gas Division continued to meet all demands for helium .

Jun 1, 1949

By Z. Zhiqun, V. A. Marple, B. Y. H. Liu

"IntroductionIt is commonly understood that aerosol particles may be injurious to human health if they are of a size that enables them to enter the respiratory tract. Coal Workers' Pneumoconiosis (CWP) is one disease known to be caused by coal mining related particles.The location in the respiratory tract where the particles are deposited is primarily a function of the equivalent aerodynamic diameter (EAD) of the particle. The equivalent aerodynamic diameter is the diameter of a spherical particle with a density of 1.0 gm/cm3 with the same falling speed as the particle in question. For a spherical particle the calculation is rather simple in that the equivalent aerodynamic diameter is simply the diameter of the particle in question multiplied by the square root of the density of the particle. For irregularly shaped particles, such as coal particles, there is no simple way to make the EAD calculation. For example, Figure 1 is only one of an infinite variety of particle shapes that can be found in practice and the aerodynamic size of this particle and, therefore, its deposition location in the respiratory tract would be nearly impos-sible to estimate accurately.The normal method for determining the aerodynamic diameter of particles has been to experimentally measure the size of the particles in a settling chamber or with an inertial classifier such as an impactor, cyclone or a centrifuge, since inertial classifiers have the property of classifying the particles according to their aerodynamic diameters."") However, these devices can only give limited information on the EAD of a single particle with a specific shape. Impactors and cyclones, for example, collect particles in size ranges and not at a specific size, so the determination of the EAD of a specific particle is not possible. A centrifuge, on the other hand, can measure the EAD of a specific particle but the equipment is costly and procedure laborious, and it may not be possible to disperse a particle of a specific shape into the centrifuge. The centrifuge can be used to determine the EAD of clusters of spheres in various arrays, but introducing particles of a specific irregular shape may not be feasible. Furthermore, the EAD is a function of the orientation of an irregularly shaped particle and the orientation of a particle in an inertial classifier is unknown. The orientation may also vary as the particle passes through the classifier.Because of the difficulty in determining the EAD of an irregularly shaped particle, we have undertaken a program to apply theoretical numerical methods to calculate the EAD of any shape particle. In our laboratory we have, for some time, been using numerical methods to determine the flow field of air within instruments such as impactors, (2) inlets, (3) and virtual impactors (4) Recently, this technique has been expanded into the three-dimensional regime, and the flow fields and particle motion characteristics within cyclones (5) and glove boxes have been studied. We have now begun to use these numerical three-dimensional flow programs to study the flow field around irregularly shaped particles to determine their drag coefficients, falling speed, and thus, their EAD."

Mar 1, 1989

By Bernard Porter, E. A. Brown

Electrical conductivities and densities of the LiF- UF , LiF- ThF4 , NaF - C1F4 , and NaF - ThF systems were measured as functions of composition and temperature . The specific conductance and density varied linearly with temperature . Molar and equivalent volumes , as well as heats of activation for conductance , were calculated from the experimental data . At 1,000 ° C , the molar volumes ranged from 16 to 40 cubic centimeters per mole and the specific conductance ranged from 9.8 to 2.5 per ohm- centimeter as the actinide metal fluoride concentration changed from 0 to 60 mole - percent . Heats of activation for conductance were 3 to 7 kcal per mole . The data are interpreted on the basis of a semilattice model for the melts .

Jan 1, 1964

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal, (2) to upgrade marginal coals through effective preparation, and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the seventh of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Floyd County, KY., which comprises parts of the Paintsville, Prestonsburg, Harold, Hindman, and Pikeville quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all avail-able data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By T. T. Campbell

A survey of the literature eras made covering the use of aqueous non-aqueous, and fused-welt systems for the electrowinning or electroplating of molybdenum metal. The survey was prepared in order to provide background for further investigations directed toward the electrodeposition of pure molybdenum metal from either aqueous or nonaqueous mediums. While a thorough effort was made to cover all available references, a critical review was not attempted nor does this survey pretend to be exhaustive in nature.

Jan 1, 1955

By B. K. Shibler, J. V. Batty, G. M. Potter, H. D. Snedden

"INTRODUCTION As a part of the investigations of strategic mineral deposits in the United States under the Strategic Minerals Act. Engineers of the Bureau of Mines examined and sampled numerous deposits pf fluoride ores in the Western States. Sample from those deposits that warranted further investigation were submitted to the Ore Dressing Section of the Salt Lake Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory studios of fluorite ores submitted from 12 deposits in Arizona, California, Idaho, Montana, Nevada and Wyomong. Only four of the Ores were found to be amenable to beneficiation for the production of acid-grade fluorspar concentrates with good recoveries. However, all of the samples were amenable to the production of concentrates meeting chemical specifications for metallurgical-grade spar.For the sake of clarity and convenience in presenting data, this report has been divided into six parts, each pertaining to metallurgical studies of fluorspar ores of a single State."

Nov 1, 1947

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By C. J. Wilhelm, John M. Devine

"Hydrogen aulphide associated with natural as was noted as early as at Point Albino, Canada. 4 The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence ma by no means common. However, in recent years, with the development of the producing zones of west Texas and the Texas Panhandle the production of ""sour"" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor-frequently a major problem—in the drilling and operation of any wells in those areas.The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen sulphide. From the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. 5 Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.6"

Sep 1, 1931

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

By Albert L. Toenges

This paper is the third of a series4/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. The mining of coal by means of mechanical devices has emphasized the need for continued study of the relationship, of these devices to existing physical conditions and to planning of the operations for increased safety and economy. The purpose of this investigation is to stud the operations of different types of mechanization used in mines under various systems of mining and physical conditions to reach conclusions as to the safest and most economical methods and practices of mining. Physical conditions very in different and in the same mining districts and determine, together with economical conditions, the systems of mining and the types of mechanical loading equipment used. The information presented in this paper

Jan 1, 1941

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By F. W. Horton

Investigation of an extensive deposit of chromite-bearing actinolite-talc schist situated on the summit of Casper Mountain, 10 miles south of Casper, Wyo., was one of the first projects Undertaken by the Bureau of Mines under the Strategic Materials Act (Public 117, 76th Cong., Ch. 190, 1st sess.), for which an appropriation became available August 9, 1939. During the previous summer; the Geological Survey? made? a magnetometrical survey of the area in which the schist occurred. It was exposed in several small lenses and two larger ones aggregating about 19?acres in area. Although the occurrence of chromite here had been known for many years, the only work done on the deposit was the digging of? a few shallow pits on some of the more promising outcrops. From August 23 to December 3, 1939, the Bureau of Mines investigated the larger of the two main schist bodies. Twenty-four trenches having a total length of 8,073 feet were dug across the deposit, and its subsurface extension was explored by 3,623 feet of diamond drilling. Over 32 tons of samples were shipped to the Metallurgical Division of the Bureau of Mines at Reno, Nev., for reduction, analysis, and ore testing. In all, there were 853 individual samples. Geological maps, based upon examination of outcrops, trenches, and drill cores, as well as a contour map of the area were made by the Geological Survey.

Jan 1, 1949

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By Oliver Bowles

The Bureau of Mines issued three Information Circulars on marble many years ago (5), (6), (7).2/ They have long been out of print; furthermore, conditions have changed considerably in the industry in succeeding years. A presentation of current data is therefore desirable. This report furnishes general information on marble, including its properties, distribution of domestic and foreign deposits, methods and equipment used in quarrying and milling, economic and marketing problems, and recent advances in marble technology. INTRODUCTION Most marbles are crystallized limestone. The term "marble" is derived from a Greek word meaning to sparkle or flash, because the calcite crystals in marble sparkle as they reflect light. The word "marble" is employed frequently to mean a small ball used in the game of marbles with which nearly every child is familiar. Although the little spheres were originally of marble, few of those made in recent years contain that material; nevertheless, the expression "playing marbles" has persisted.

Jan 1, 1958