Search Documents

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By James A. Brierley

Wastewater from uranium mines in the Ambrosia Lake district near. Grants, New Mexico, U.S.A., contains uranium, selenium, radium, and molybdenum. The Kerr-McGee Corporation has a novel treatment process for waters from two mines, sections 35 and 36, to reduce the concentrations of the trace contaminants. Particulates are settled by ponding, and the waters are passed through an ion exchange resin to remove uranium; barium chloride is added to precipitate sulfate and radium from the mine waters. The mine waters are subsequently passed through three consecutive algae ponds prior to discharge. Water, sediment and biological samples were collected over a 4-year period and analyzed to assess the role of biological agents in removal of inorganic trace contaminants from the mine waters.

Jan 1, 1981

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By S. W. Zoldok

"ERRATUMFor paragraph 1, page 1, read the following:The Cle Elum nickeliferous iron deposits occur on an unconformable contact between the serpentine and overlying Swauk sandstone formation and extend about 2 miles along the Cle Elum River in Kittitas County, Wash.The linear extent of the deposits and their proximity to a large source of,electric power and coal supply indicated that a development program was in order to determine the probable grade, extent of the ore bodies, and a suitable metallurgical process for recovering the iron, nickel, and chromium from the ore.The northern portion of the serpentine formation was investigated by the Bureau of Mines from August to December 1943 and from August to October 1944. The investigation consisted of road building, diamond drilling, sampling, and metallurgical tests.The Geological Survey assisted with logging of cores and made geologic and topographic maps."

Feb 1, 1948

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By J. R. Thoenen

"The curtailment of imports of foreign potash during the World War directed attention to the necessity of establishing a domestic source of potash for fertilizer, and considerable study has been given to the subject by Government bureaus, research organizations, and private individuals. These studies have covered all known sources of potash, and among them the extensive greensand deposits of New Jersey in which the potash content is found in the mineral glauconite have been investigated.Several hundred patents have been obtained covering processes for the extraction of potash from siliceous minerals, but up to the present time none have proved successful on a large commercial scale.When the investigation of the potash deposits of Texas was started by the Federal Government, the laboratory study of the drill cores was assigned to the Nonmetallic Minerals Experiment Station at New Brunswick, New Jersey, with the object of ascertaining a possible commercial method of utilization.The purpose of this preliminary study was to investigate existing literature and previous investigations to ascertain the extent and availability of the deposits, the extent of commercial success so far attained in potash extraction, the most promising known methods and by-products obtained from them, probable markets, and possibility of competition with foreign potash, and by a study of these data to determine whether further chemical engineering analysis and laboratory investigation were warranted.As the study advanced it became evident that adequate reserves of green-sand were available for many years supply. and that whereas many processes had been patented few had been tried commercially. In collaboration with former private and Government investigators these patents were first divided into two"

Feb 1, 1929

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By E. Robert Ruhlman

["Phosphate rock" is a broad term applied to natural deposits of minerals valued chiefly for their phosphorus content. More specifically, phosphate rock may be defined as a natural rock containing one or more phosphate minerals, usually calcium phosphate, of sufficient purity and in sufficient quantity to permit its use directly, or after beneficiation, in the manufacture of phosphorus-bearing products. The grade or quality of phosphate rock is expressed either in terms of its phosphorus oxide (P20S) content or the equivalent in tricalcium phosphate (Ca3(P04)2). The trade name for tricalcium phosphate is bone phosphate of lime (B. P. L.).]

Jan 1, 1958

By John G. Palmer

Continued development of an especially impregnated silica gel capable of reversible chemical detection of carbon monoxide (CO) was reported. The affects of changes in mine-related ambient conditions on the detection catalyst's response were explored. Temperature, humidity, and several interfering gases were found to affect the detection catalyst. The interferents include hydrogen sulfide, nitrogen dioxide, acetylene (and methylacetylene), and ammonia. High humidity decreased the detection catalyst's sensitivity to carbon monoxide for some formulations. Increasing temperature generally decreased the reaction time of the detection catalyst with carbon monoxide. Badges and carriers for the visual presentation of the detection catalyst were constructed. Several variations of these devices included provisions for absorbants and filtering agents which help protect the detection catalyst from gaseous interferents. A variety of catalyst support agents were tested in an effort to find the most suitable. Included were alumina, magnesium oxide, magnesium silicate, and several forms of silica gel. In addi tion to free-flowing forms of these sorbents, thin layer chromatography plates coated with cellulose, alumina, and silica gel and newly developed PTFE entrained silica gels were examined. A limited physical, chemical, and mechanistic characterization of the detection catalyst and the materials used to prepare it has been carried out. Metal component ratio studies, spectral, analytical, pH, and rate measurements were done.

Jan 1, 1982

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

By Nathan T. Lowe

This report updates an accounting of mines and prospects in the Seafoam mining district, Custer County, Idaho, begun during mineral appraisal of the Idaho Primitive Area. Thirty-two mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of mineral appraisal of the River of No Return Wilderness; most previously known locations were field checked and the updated information added to the data base. The district's major deposits include polymetallic fissure veins of gold-silver-lead-zinc-copper hosted by granodiorite and quartz monzonite which have been intruded by dikes ranging in composition from rhyolite to dacite, and vein type replacements of silver-lead-zinc-copper hosted by calcareous xenoliths imbedded in major intrusives. These deposits may be related to the intrusion of the Rapid River pluton or the Casto pluton. The dominant northwest structural trend is parallel to an aeromagnetic high, a weak gravity salient, and the Blue Bunch Mountain dike swarm.

Jan 1, 1983

By Louis Schaffer

The purposes of the research were to assess the applicability of new accident investigation methods to mining accidents, and to adapt those found to be applicable in the development of a new methodology for use in mining. The development included field testing, evaluation and modification of the new methodology. The report is in two volumes. Volume one discusses the background research, the design of a methodology for field evaluation, preliminary field tests in Utah mines, and work done to prepare for a formal, complete evaluation by federal government mine safety officials. This, volume 2, discusses the field evaluation done by the contractor and cooperating mines after the program was re-directed by the Bureau of Mines. It relates to research done during a period of approximately eighteen months, ending in April, 1983.

Jan 1, 1986

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981