Search Documents

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By N. A. C. Smith, E. W. Dean, W. A. Jacobs, H. H. Hill

Fractional distillation is the most important process in the commercial refining of petroleum. The same procedure, conducted on a small scale, is the basis of a number of analytical methods of wide application in the petroleum laboratory. The Bureau of Mines has studied apparatus and procedure for the distillation analysis of petroleum, and this report is presented as a record of developments up to the present time. The work is incomplete, but the extensive information that has been obtained to date is made available as a guide in handling laboratory distillation problems. The analytical distillation of petroleum is commonly made to determine range of boiling points or to separate the oil. into fractions for detailed examination, or both. When only one of these two ends is sought the procedure involved is notably simpler than when, as is more common, information is required regarding both boiling range and properties of fractions. Moreover the degree of minuteness of measurement and the accuracy of the data required from analytical distillations differ considerably. Often the simplest sort of comparative figures are satisfactory; other tests require complicated and highly tedious procedure. No one distillation method is universally applicable, and it is impossible for anyone group of investigators to foresee all the different kinds of requirements that may occur in the industry.

Jan 1, 1922

By D. Harrington

Probably over 95 percent of the coal production of the United States depends upon the use of explosives before it can be placed in the railroad car at the mine, and up to the present time it has been impossible to obtain Pry kind of practicable explosive that isn't dangerous unless handled carefully. In other words, no "foolproof" explosives have been found to date and inspection of the accident records of the coal mines of this country indicates that the use of explosives in coal mines has taken a sad toll of lives. ACCIDENTS PROM EXPLOSIVES IN COAL MATES Of the 2,000 to 2,500 persons killed annually in the coal mines if the United States, 100 to 125 have been killed from explosives without an explosion of gas or dust; these accidents have been due to misfires, hangfires, premature blasts, or accidental setting off of explosives through carelessness or otherwise (but chiefly through carelessness in some form). In this type of accident the flame character of the explosive is not necessarily involved, although an unexpected or premature blast is initiated much more easily with black blasting powder, which has a long flame, than with a permissible explosive, which has a flame much shorter and of briefer duration. By far the greater number of such accidents are caused by black blasting powder or dynamite rather than by permissible explosive.

Jan 1, 1936

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946

A preliminary program dated April 25, 1974, was prepared for Development Engineering, Inc. (DEI) on research and development. for laboratory, field and other engineering studies on the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included discussions on the peculiarities of retorted shale materials to be investigated and discussions of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I Program Development. II Exploratory Laboratory Tests on Old U.S.B.M. Retorted Shale. III Laboratory Tests on Pilot Plant Retorted Shales, IV Laboratory Tests on Retorted Shale from the Semi-Works Plant, Field, Test Plots and Ponds. V Field Compaction Tests. VI Infiltration Pond Tests. VIII Final Report.

Jan 1, 1975

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 120 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257; 7267,`7273; 7285, 7292, 7303, 7310, and 7324. 1. GRAVITATIONAL METHODS 7933. Ansel, E. A Eine Untersuchung zum Problem der Isostasie (An Investigation Regarding the Problem of Isostasy). Gerlands Beitr. Geophys., Leipzig, vol. 59, 1942, pp. 16-26.

Jan 1, 1945

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By Charles Zahn

Direct mass spectrometric determination of alcohols in the presence of hydrocarbons has not been possible because of the similarity of hydrocarbon and alcohol mass spectra. Experiments have demonstrated that by converting the alcohols to their trimethylsilyl derivatives, characteristic mass spectra are obtained free of interference from hydrocarbon ion fragmentation. Hexa- methyldisilazane is the reagent selected for the conversion, An improved method of preparing the reagent is given, Mass spectrometric determination of alcohols as trimethylsilyl ethers now is not only possible without prior separation from other materials, but the range of the room-temperature mass spectrometer is also extended to include the C10 alcohol region. Water does not interfere because it is converted to hexamethyldisiloxane, which has its own distinctive mass spectral peak, Experience indicates that other compounds such as glycols, amines, and phenols probably could also be determined by mass spectrometry of their trimethylsilyl ethers. Studies on the similar detemination of phenols in coal oils have been started, When mass spectrometry is not available, gas-liquid chromatography of alcohols before and after their conversion to the trimethylsilyl derivatives probably could be performed. The preparation and properties of the trimethylsilyl derivatives of 23 alcohols, 2 glycols, 3 amines, and 1 mercaptan are detailed. INRODUCTION During investigations by the Bureau of Mines at the Pittsburgh Coal Research Center relative to the development of Fischer-Tropsch processes, complications were encountered in the mass spectrometric analysis of alcohols in hydrocarbon oils. The fragmentation peaks of the alcohols and the hydrocarbons were so similar that an accurate analysis was not possible, Since involved separation techniques are necessary to isolate alcohols from hydro-carbons for separate determinations, efforts were turned to the search for a

Jan 1, 1962

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By K. Robert Dorman

Spray-applied polyurethane foam was used to insulate the walls of heated rooms excavated in permafrost. The experiment was designed to determine whether polyurethane foam can be sprayed successfully on frozen ground under freezing conditions and to measure the effectiveness of the insulation in maintaining--at elevated temperatures for an extended period--a room excavated in frozen ground. Two manufacturers' foams were investigated in the laboratory. Subsequently, one of the foams was employed to insulate two small rooms, one in frozen gravel and one in frozen silt, in an experimental tunnel belonging to the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL) near Fairbanks, Alaska. Following insulation, heat was introduced into the two rooms. Heat migration across the insulating barrier into the walls, in addition to wall closures, was monitored over an 8-month period. The results show that polyurethane foam can be successfully sprayed on frozen ground in below-freezing temperatures. Given this type of insulation, together with winter cold to supercool the surrounding ground, it should be possible to maintain a shaft or heated room in permafrost for several years.

Jan 1, 1970

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By W. A. Selvig

EQUIREMENTS of montan wax for industrial use in the United States before World War II were met by imports, nearly all of which came from Germany. An important industry for extraction and refinement of this wax from certain brown coals had developed in Germany. At the beginning of the war, montan-wax imports were shut oft, and American industry was forced to rely largely on substitutes. Since the war, relatively small amounts have been imported from Czechoslovakia. Because of the shortage of montan wax at the close of the war and the fact that industry in the United States had to rely on foreign sources in the past, this investigation was started in 1945 to determine probable yields of wax from domestic lignite. Results of the investigation and the properties of extracted waxes are described in this report. Also included in the report are discussions of the occurrence and geology of lignite deposits of the United States from which samples were obtained for wax extraction and the petrographic composition of lignites, particularly in respect to those components that contribute to wax yields.

Jan 1, 1950

By R. T. C. Rasmussen

"INTRODUCTION The primary purpose of the Bureau of Mines electrolytic manganese pilot plant at Boulder City, Nev., is to improve the Bureau-invented electrowinning process and to determine the applicability of the process to the extensive domestic low-grade manganese ores with a view to making the United States dependent upon foreign sources of manganese. 3/4/ Incidental to accomplishing this purpose, the pilot plant has produced a substantive quantity of electrorytic manganese since the start of operations late in 1941; present cabacity about 1 ton a day of manganese metal. A second important purpose of the pilot plant is the supplying of electrolytic manganese for full-scale tests in cooperation with industrial users of manganese.The Rustless Iron& Steel Corp., Baltimore, Md., was the first steel company to cooperate with the Bureau of Mines in large-scale testing of electrolytic manganese. Arrangements were made with C. E. Tuttle, then president of the corporation, whereby the Bureau would supply electrolytic manganese to make a sufficient number of full-scale stainless-steel heats to demonstrate thoroughly its merits as a replacement for low-carbon ferro-manganese in the corporation's stainless-steel practice. The corporation's purpose in the investigation was to determine the possible advantages of electrolytic manganese resulting from its almost complete lack of phosphorus and caroon that might offset its then considerably higher cost per unit of manganese than low-carbon ferromanganese. The data presented herein are based upon reports of A. L. Field, technical director, and L. Weitzenkern, research engineer of Rustless Iron & Steel Corp.; they are supplemented by observation of the author who visited the plant during the tests."

Oct 1, 1945

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962