Search Documents

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation. In order to insure accurate data, tight field controls were adhered to during the drilling and blasting process as they related to blast design, bench preparation, pattern layout, drilling and blasthole loading. Following the blast the excavation and crushing procedures were studied to quantify any down stream advantages due to improvements in fragmentation. This study will help provide the industry with information as to the advantages of high accuracy electronic blasting systems over conventional pyrotechnic systems and show the results of an operation utilizing electronic detonator technology through their production season.

Jan 1, 2000

By Braden T. Lusk, Shannon P. Lusk, Kyle A. Perry

A high explosives shock tube has been constructed and developed to test blast resistant windows with pressure versus time waveforms similar to waveforms generated by arena testing. Calibration of the high explosives shock tube, or Large Arena Test Simulator (LATS), included numerous tests performed by detonating varying charge weights at different distances from three piezoelectric pressure sensors located at one end of the shock tube (where the test subject would be installed). The maximum reflected pressure and positive phase impulse were calculated for each waveform generated in the tests. Pressure versus distance and impulse versus distance graphs were generated. Results have been graphed in order to predict charge weights and distances that correlate to the desired pressure and impulse at the end of the tube for future tests. This is a valuable tool when testing expensive, job specific components so the loading requirements are met on the first attempt.

Jan 1, 2010

By Crazy Horse - The Journal of Explosives Engineering - Vol 20 No 1

The crew at Crazy Horse Memorial has produced a w o n d e rful new video called “The Fine Art of Mountain Carving.” The video closely examines for the first time, the extraordinary explosives engineering on the Crazy Horse mountain currently in pro g ress in the Black Hills of South Dakota. The 56-minute video takes the viewer up the mountain for a behind-the-scenes look at the drilling and blasting crew at work on the mountain. The video was written, edited and produced by Robb D e Wall and is available exclusively from the Crazy Horse Memorial in both DVD and VHS formats. For i n f o rmation, see www.crazyhorsememorial.org The following, is a brief summary of the 25 steps involved in carving the mountain. The video goes into extensive detail on each of the 25 steps. Both those in the explosives industry and those outside the industry will find the video intere s t i n g .

Jan 1, 2004

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By Claude Cunningham

Difficulty has always attended the evaluation of rock breaking energy available from explosives, owing to the complexity of the way in which it is released, and the destructive amplitude of the pressures. Many problems have arisen and continue with this difficulty, including the following: I. Formulation of improved compositions to deliver appropriate energy levels to the blasthole walls, or to deliver previous results at improved cost. How appropriate is it to use various ingredients, such as Aluminium, water, salt? 2. Claims over energy issues, resulting in wasted time and expense, over things that sound good in theory but are very difficult to tie down. 3. Purchasers of explosives make decisions based on claimed “Bang per Buck” from different manufacturers, where the estimate of “Bang”comes from simplistic numbers from various, very unequal detonation codes. The above problems are escalating as time progresses. Using the high level IDeX PC 2000 detonation code, we have found a way to portray the differences between formulations in a way which relates to their breaking effect in the field. The basic method is to plot the adiabat from the detonation state to full expansion in units which express the practical implications. Energy alone cannot deliver results, so we use the curve to examine its manifestations: pressure and temperature. Internal energy is plotted with these. The method displaces relative energy numbers, as it portrays the context in which the energy is available. It is used here to compare an ANFO, an emulsion and a doped emulsion, as well as the effect of Aluminium. The effect of the shock pressure regimes and temperature correlate well with what is seen in the field.

Jan 1, 2000

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By Kenneth Eltschlager

Business says that location is a primary component of being successful. So too is the importance of location in blasting. For blast seismograph data to be useful, the location of the blast and seismograph must be clearly documented. Another location of importance is that of a nearby structure. Establishing the spatial relationships between the blast, seismograph and nearby structures, allows the blaster to correctly interpret the data, evaluate the performance of the blast and gauge the validity of any complaints.

Jan 1, 2004

By Douglas Rudenko

Most engineers, mine operators, or contractors acknowledge the importance of having accurate subsurface information in order to plan a project or solve a problem. Conventional methods of exploring the subsurface such as augering, core borings, or test pits can provide information, but it is often costly and sparse. Geophysical methods offer an alternative to help supplement sparse information~ gathered through conventional exploration techniques.

Jan 1, 1998

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Kirstin Girdner, Tom BoBo, Brian Norton, John Kemeny

Split Engineering is a truly customer oriented company dedicated to providing quantified fragmentation information of the highest integrity to enable process management and control. Technical decisions, blasting costs, operational efficiency and productivity and equipment performance can all be related to optimum fragmentation. In the past, the lack of an easy, non-disruptive, economical measuring technique has meant that, in most cases, rock fragmentation has not been defined in quantitative terms. Now, the Split-Desktop@ software provides an economical alternative to manual sampling and screening and an objective measure rather than subjective qualitative estimates. This workshop will present the latest features of the Split-Desktop@ software and show users how to quickly get quantifiable results from their blast fragmentation. A step-by-step demonstration will display the software’s flexibility, user-friendly options, and ease of use. Outlining where other mines have benefited from using the Split-Desktop@ software will provide insight to a wide range of software uses and potential applications like creating a database of geologic zone specific post-blast fragmentation information, underground draw point monitoring, stockpile, leach pile, and waste dump size measurement and monitoring, as well as many other applications.

Jan 1, 2000

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012