Search Documents

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By Norm Tienkamp, Normand Martineau

Through the normal course of operation, mine operators are living situations where blast results need to be measured. It becomes the supervisory group responsibility to select evaluation parameters with appropriated and available technics. In Mine Selbaie's case, we have retain the following parameters: rock fragmentation, oversize fragments, rock pile movement, grade rupture.

Jan 1, 1996

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Simon St. John Tose

We have had a long history in supporting the development of training material to ensure “safe” blasting. This has been provided as both significant technical guidance to the industry and input into the development of the new industry surface rockbreakers or shotfirers qualification in South Africa (RSA). The learning material supplied to the industry is based on both a classroom knowledge component and an assessment on the practical application of the learning by the trainee blaster on the job under the supervision of the appointed blaster. This training includes all blasting applications which can often extend beyond the “normal” mining environment of open pits, underground and quarries into civil applications such as trenches, blasting close to private buildings, public roads, pipelines, power lines, swimming pools and the removal of concrete structures and building demolitions etc.

Jan 1, 2013

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Lyle Dennis

Emphasis on increased production while maintaining rigid quality standards has necessitated a change in blasting technology at Dacotah Cement's limestone and gypsum quarries. The following three methods implemented during the past three years have yielded an increase in production through improved fragmentation.

Jan 1, 1996

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

By Ricardo Gaviria, Vincinte Acosta

There are major blast design and field procedures differences between conventional blasting in horizontally bedded coal seams and blasting underneath coal seams in a multi seam deposit with seam inclinations of 14 degrees or more.

Jan 1, 1995

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yuji Wada, Yukio Katoh, Yoshikazu Hirosaki

In our previous work, the results of photographic observation using a high speed framing camera showed that the difference between precursor air shock wave velocity and detonation velocity was primary factor for the channel effect. It is assumed that the decreasing precursor air shock wave velocity can prevent the channel effect in charge hole.

Jan 1, 1996

By Ian R. Firth

For the majority of open pit precious metal mines in the western United States, grade control practices have evolved as a direct result of the variable geology of the ore body and the lack of a clear visual or geologic distinction between ore and waste material. These practices often include the extensive use of buffer or choke blasting, in an attempt to minimize lateral movement of the muckpile. The Mackay School of Mines is conducting ongoing research, which aims to develop a practical method of measuring the movement of discrete “targets” placed within the body of the blast. The movement experienced by these targets can then be used to interpolate the movement of the blast as a whole. Typically, the boundaries between different material types are known as digging limits or polygons and are marked using colored flagging on the muckpile. If material movement can be measured using targets placed in the blast, these digging limits can be altered to reflect the blast-induced rock movement, reducing dilution and improving value recovery.

Jan 1, 2002

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By Kevin Landey, Eric Gerst

Expanding blast patterns to near the limit of an explosives’ ability to do the necessary amount of work is a common practice to reduce drilling and blasting costs. Choosing less expensive explosives such as ANFO vs. emulsion, bulk product versus packaged product, etc. are also common cost savers. Both practices are only effective as long as the pattern geometries are accurately drilled. However, will pushing the limits on pattern sizes and explosive products produce consistent results at the face, minimize oversize, produce superior fragmentation, and improve crusher throughput? Sometimes, but no amount of explosives can overcome a poorly drilled pattern. Knowing the probable outcome of any changes in drilling and blasting is valuable in achieving success.

Jan 1, 2018

By P Geddes, K Grohs, C K. McKenzie, M Morrish

Low grade surface gold mining at the Acacia Resources, Union Reefs Gold Mine in Australia's Northern Territory, involves the excavation of benches in three slices after blasting. Blast patterns span zones of high and low grade ore, as well as zones of waste, and selective excavation is required in order to maintain economical head grades for the carbon-in-leach processing plant.

Jan 1, 1998