Search Documents

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

Nowadays, with such a focus on environmental protection, surface mining activities have come under pressure to ensure their activities do not adversely affect the local surroundings. As part of the extractive process, blasting activities are an integral part of a mining company’s operational cycle. Consequently achieving beneficial blast results while complying with environmental requirements has become a key focus. This especially is the case when firing blasts within close proximity of residents where additional control measures need to be implemented to control vibration. One case where this occurs in Indonesia is in the Paringin Pit, one of the operational areas of the company's. The pit has complex geological conditions and is surrounded by several residential areas. Between 2014 to 2017 there were 12 cases of ground vibration exceedance due to blasting. As part of a continuous improvement project the company's targeted minimizing the vibration exceedance in this area. A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control. With this new approach geological condition mapping with specific spatial range was produced that would minimize vibration while ensuring beneficial blast results. Introducing the new prediction produced nil cases of vibration exceedance in 2018 and beyond and proved that the Signature Hole Analysis in specific spatial range of geological condition is the preferred method to optimize blast result and maintain vibration control.

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By William Wilkinson, Vladisla Kecojevic

Current three-dimensional (3D) computer design technology leveraged into drill and blast planning and operations is changing the way engineers and operations approach drill and blast design. Additionally, Global Positioning Systems (GPS) technology that is now readily available to the civilian population is being implemented into the mining sector with a variety of new products specifically designed for drill and blast operations. The objective of this article is to discuss the steps involved with 3D Computer-Aided Design (CAD) of drilling and blasting, and the benefits such a design can provide in conjunction with GPS and drill monitoring systems.

Jan 1, 2004

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By Rhys Baker, Tim O’Brien, Joshua M. Hoffman

This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms.

Feb 1, 2020

By Pierre L. Labelle

Non electric Dual Delay initiators have revolutionized many aspects of underground mining. The units are used in all types of underground blasting operations. Some operations, due to the complexity and variety of their blasts, have extremely large inventories of conventional non electric products. The Dual Delay system has drastically reduced these inventories and has added an important element of versatility to blast designs.

Jan 1, 1994

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By Brian W. Stump

Seismic networks provide the primary technology for monitoring compliance with a comprehensive test ban treaty. The design goal of the network is the identification of possible clandestine explosions detonated below the earth’s surface and possible in the oceans. Complementary technologies such as infrasonic, hydroaccoustic and radionucleide (particulates and noble gases) monitoring supplement the seismic monitoring covering explosions in the atmosphere and oceans. Seismic sources that will produce detectable signals will be both natural and man made in origin. Naturally occurring events include earthquakes, many of which are beneath the oceans or deeper than it is possible to drill, and volcanic eruptions. Accurate locations of such events to depths of beyond 10 km precludes consideration of these events further.

Jan 1, 1995

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By David Flores, Benjamin Cebrian

Gold mining require high levels of dilution control due the high value of ore. These types of operations employ short benches, which are suitable for ore control, lower displacement and more representative block models. However, shorter benches makes fragmentation by blasting difficult because blast designs tend to be stiff in regards to burden/bench height ratio. This is especially relevant in hard, massive ore bodies where usual drilling diameters lead to poor energy distribution. In regards to control ore loss and dilution, there are different techniques to minimize both, which include: panel blasting, buffer blasting to muck piles and differential loading of areas of the blast bench. All of them should be sequenced with appropriate displacement along the ore/waste contacts. This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By H Ulrich Leiste, Leslie Talor

This paper describes a series of small scale tests conducted to investigate the loading applied to a flat plate by the detonation of a cylindrical charge very close (between two and three charge radii from the center of the charge) to the structure. The testing used very small quantities of explosive (PETN): Two different series of tests were conducted. In the first test series, impulse loading on the target plate was investigated using three different sizes of charge. In the second series, pressure time profiles were determined. The charge size was 6 g or less. Impulse was found using high speed video of the target plate to determine its displacement as a function of time, from which initial plate velocity was obtained. Kolsky Bars, placed at the same distance from the charge as the target plate, were used to determine the free-field pressure time profile of the output of the charge at this distance. Two different types of target plates were used in the impulse study. One was just a plate while the other was a plate constrained with a steel frame.

Jan 1, 2009

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005