Search Documents

By A. Pope

I have attended two Explosives Engineers’ Conferences in the past 4 years. The first was in Brighton, England with the European Federation of Explosives Engineers in 2005 and the International Society of Explosives Engineers in New Orleans, USA in 2008. At both of these conferences I listened to papers presented on European and English training methodologies and ideologies. As I have been training Shotfirers for the past 18 years in Queensland and the Northern Territory for some 8 years previously, I would like to present our methods of training in Queensland, which I believe is among the best in the world. In Queensland, this training is carried out by a training organisation that is registered by the Department of Education, Training and the Arts under the guidelines of the Australian Quality Training Framework (AQTF). Not only is this Registered Training Organisation (RTO) required to operate under these very comprehensive guidelines, but also those designated by the Explosives Inspectorate of the Queensland Department of Mines and Energy.

Jan 1, 2009

By R W. Givens

This paper presents blast casting design variables that have been developed and are currently being used at the High Power Energy mine in West Virginia. The shot specifications are summarized in Table I. The two active casting pits were designed with casting in mind and as a result are better designed and more efficient. About 55% of the overburden material is effectively cast and clean up is done by a bulldozer, front-end-loader, and trucks. This results in a 15X decrease in the cost of coal production.

Jan 1, 1988

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By B Mohanty, R Yang

Blasting vibration information is now commonly used to diagnose blast malfunctions. These range from limiting vibration levels to protect normal dwellings to determining scatter in detonator firing times, and even to rating of explosives in the borehole. Although blasting vibrations have the potential to yield reliable information in all these issues, there are key restrictions on their specific use, which are often ignored. These include all aspects of instrumentation, and sensor layout, as well as methods of analysis. This paper highlights these limitations. It emphasizes the distinction between near-field and far-field seismic recording in terms of borehole dimensions and blast geometry. Several case studies from both underground and open-pit blasting operations are discussed to illustrate and emphasize the essential characteristics of blasting vibrations and their optimal use in diagnosing blast malfunctions.

Jan 1, 1997

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By Catherine T. Aimone

A series of experiments have been performed to characterize fragmentation and microcracking in quartz monzonite copper porphyry. The flyer plate impact method was used to generate plane shock waves in rock specimens for impact pressures between 1.6 and 7.3 GPa and impact pulse durations between 1.1 and 7.0 µs. The effects of pressures up to 4.8 GPa and pulse duration on fragment size distributions and microcrack densities were studied. The results show that pressures effect particle sizes to a greater extent at higher pulse durations. However, changes in pressure and pulse duration show little influence on the density of microcracks induced during explosive loading. These results indicate that the nucleation and growth of microcracks in rock subjected to shock waves occur uniformly throughout. A substantial decrease in particle sizes for high pulse durations is attributed to more time allowed for microcracks to grow and coalesce, forming individual particles.

Jan 1, 1985

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Donald J. Moore

It has become more important today than ever before to reduce costs and improve equipment utilization. One area where such improvement can he achieved is in the use of explosives. Effective blast design for efficient use of explosives as well as optimum fragmentation can achieve this. Towards this end we must have available to us a practical design method in which experience and observation can be translated to engineering concepts. We must he able to communicate the design data to field blasting personnel as well as management in an understandable way.

Jan 1, 1975

By Advanced Initiation Systems Inc

10 years in R&D Last 5 years available commercially Worldwide Met strict approvals for manufacturing and use

Jan 1, 2004

By Quian Liu

Since the establishment of the CANMET Experimental Mine in Val d'Or, Quebec in 1991, research activities in rock fragmentation have been carried out not only in the underground laboratory but also in production mines in the north-west Quebec region. Among the instruments available for rock fragmentation, the Kodak EktaPro 1000 Motion Analyzer (also called the high speed video system) has been one of the most useful tools for monitoring blasts in both underground and open pit. This system is capable of recording events at rates from 50 to 12,000 frames per second (fps). The buffer memory has a capacity of storing 2050 images. To use this system in the underground, a steel box was made with a bullet-proof glass in the front to protect the camera. The processing and recording equipment are placed in an aluminum case which can be located about 30 m away from the camera via an extension cable. For each blast monitored, high frequency geophones and accelerometers were used to monitor ground vibrations and give a timing reference of the explosive detonations to correlate with the observation of the captured images.

Jan 1, 1994

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By Adrian Moore, Alan Richards

Time window techniques that limit the explosive charge mass being fired within a specified time window (commonly 8 milliseconds (ms)) have been used for many years and are widely accepted by explosives engineers. The 8 ms time window may be relevant for controlling ground vibration for small blasts at close quarters in a high frequency vibration environment. For controlling ground vibration from blasts in a low frequency vibration environment an 8 ms separation between blastholes is arbitrary and meaningless. The 8 ms time window was never intended as a means of controlling airblast. The use of time window techniques will, in many instances, result in airblast and ground vibration levels that are substantially greater than planned, with unfortunate outcomes. The uses of time windows that are inappropriate have been well explained in previous papers. This paper gives further examples of blast designs that satisfied time window considerations but have resulted in substantially greater airblast and ground vibration levels in certain directions, due to wavefront reinforcement or the combined effect of drilling pattern and delay sequence. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid blast vibration problems that result from inappropriate time window techniques.

Jan 1, 2002

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003