Search Documents

By Gabriel Aguilera, Juan Arismendy

"As a separator machine, the hydrocyclone is one of the most commonly used equipment in different types of industries and particularly in mineral processing, hydrodynamic behavior allows efficient separation, but developing tests to optimize experimental equipment is expensive, therefore Computational Fluid dynamics (CFD) becomes a useful tool for optimizing the geometrical and operational parameters, and allows to analyze and understand the dynamics within the equipment. In the research was developed to simulate of 40 mm hydrocyclone where turbulence model was used Large Eddy Simulation (LES) for the continuous phase, for the generation of the air core and for the interaction of particles at low concentrations was implemented (mixture model), after the simulation was completed validation and comparation was done between simulation values and experimental."

Jan 1, 2014

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Evvie Chockalingam

Acid mine drainage (AMD) is a perennial problem particularly in abandoned mines, occurring due to the oxidation of sulphidic mine wastes. AMD is usually characterized by high concentration of dissolved metal ions, sulphate and low pH. The efficacies of substrates such as rice husk and the bark of Eucalyptus tereticornis (Sm.) are assessed for the removal of metal ions such as iron, zinc and copper from acid mine water obtained from an abandoned copper mine. Over 99 % of Fe, 98 % of Zn and 95 % of Cu removal could be achieved from acid mine water, with a concomitant increase in the pH value by three units using rice husk as an adsorbent. With respect to tree bark as an adsor-bent, about 96 % of Fe, 75 % of Zn and 92 % of Cu could be removed from the acid mine water with an attendant increase in the pH value by two units. The free energy of adsorption of the metal ions onto rice husk and tree bark is found to be negative in both the cases, while the adsorption process is endothermic in the case of rice husk and exothermic for tree bark. The adsorption process is found to adhere to the Lagergren pseudo-first order rate equation. The reduction of sulphate con-centration in the acid mine water is achieved using a typical sulphate reducing bacteria namely De-sulfotomaculum nigrificans. Desorption experiments indicate that about 88 % of Zn, 87% of Cu and over 77 % of Fe could be recovered from rice husk and over 70 % of Fe, 82 % of Zn and 77 % of Cu could be desorbed from the metal loaded tree bark using 5 M HCl. The possible mechanisms of metal ion and sulphate removal from acid mine water using rice husk and tree bark are discussed.

Jan 1, 2014

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

By Yuexin Han

The wet preconcentration of haematite, comminuted by high-pressure grinding roller was studied, using the cylindrical ferromagnetic medium. The effects of various factors including rod diameter, rod gap and background magnetic field intensity (BMFI) on the performances of preconcentration for different size fractions and the force analysis of single mineral particles with different diameter in the separation zone were emphatically investigated. The results showed that as the rod diameter increased, the rod gap decreased, and the BMFI increased the tailings grade and the tailings yield reduced while the concentrates recovery raised that was regardless of variations in feed size distribution. For the -3.2+0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 7 mm at BMFI of 454kA/m is used to get a higher performance. For -0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 4 mm at BMFI of 263kA/m is used to get a higher performance. After the classifying preconcentration, at the optimum condition, the overall concentrate grade increases by 9.56 percentage points and the concentrate recovery is up to the 82.67% with a tailing grade of 10.68% and a tailing yield of 40.31%. The magnetic force, exerted on weekly magnetic minerals was proportional, to the specific susceptibility and square of BMFI. For the same BMFI, the magnetic capturing force on coarse particles increased, and that on fine particles decreased with the increasing of rod diameter. For the lean locked-particles, considering the gravity and viscous resistance of particles, rods with a big diameter were beneficial to the capture of coarse particles and had no influence on the capture of fine particles, while rods with a small diameter were good for the capture of fine particles and not suitable for the capture of coarse particles of lean locked-particles. Keywords: low grade haematite, high-pressure grinding roller, high intensity magnetic separation, pre-concentration

Sep 1, 2012

By John A. Rumball, Martin R. Houchin

Data from autogenous and semi-autogenous tests in a 1.67m diameter mill have been analysed in terms of a new model for rock abrasion. This model defines specific rate as the rate of production of fines (material less than 13mm) per unit mass of rock, where the term “rock” is applied to all ore pieces of ore coarser than the grate size. In most cases, an allowance for preliminary rounding and cleavage was made. A method has been developed to analyse steady-state data, using piecewise fitting to the cumulative size distributions. The model was compared to the well-established models, which are based on the population balance method. The specific rate increased for all rock sizes as the volume of 100mm balls in the mill was increased. Tests using a coarser feed and smaller balls provided further evidence that once rocks are rounded, abrasion is due to localised surface damage, caused by impacts, rather than rotational shear. An allowance for rapid rounding of jagged rocks, followed by less rapid abrasion of rounded pebbles was also tested, but the analysis was not conclusive. The average specific rate is a useful measure of the capacity of a primary mill. The effect of power intensity (kW/t of ore) was also investigated as a means of extrapolating the pilot-plant data to large production mills.

Sep 29, 2003

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By Jorge Rubio, Gabriel Berkowitz, Fabiano Capponim, Carlos Perez Guerrero, Elves Matiolo, Denise G. Nunes

This paper describes some advances in flotation research in fines (“F” 38 to 13 µm) and ultrafines (“UF” < 13 µm) mineral recovery by two different techniques, at laboratory scale. Extender flotation and flotation with .multi-bubbles. (bubbles with a wide size distribution) of copper sulphide fines (ore feed of about 1 % Cu) were compared with a .standardised. mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), .true. (bubbles-particles attachment only) flotation recoveries and process kinetics. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physico-chemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged.

Jan 1, 2003

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By L. Tong

Stirred milling of laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on a siliceous goethitic (SG) nickel laterite sample (-2000 µm particle size) to evaluate the effect of operating conditions such as stirrer speed, grinding time, pH, solid content, water salinity and charge volume. The target was to produce a -38 µm fraction in the milling product with high nickel recovery and grade. Addition of dispersant (sodium hexametaphosphate) was also optimized with respect to the rheology of the slurry. In terms of stress intensity, the optimum grinding conditions for selective size reduction were: 1000 rpm, 50 per cent charge volume. At higher stress intensity (2000 rpm), Ni recovery in the -38 µm product was higher, but Ni grade was low, due to the breakage of the harder siliceous particles. Decreasing the yield stress by modifying slurry pH or adding dispersant improved the rheological properties of the pulp, but had no great influence on Ni upgrade in the fine product. Modifying water salinity by adding 2 M NaCl had also little effect. The breakage of the +38 µm particles in the feed determined Ni upgrade greatly. Ni grade in the -38 µm product decreased with grinding time, suggesting that the Ni-bearing minerals break first, while the harder siliceous minerals have a lower breakage rate. The breakage rates with respect to sample mass for Ni, Mg and Si indicate that: Mg > Ni > Mass > Si. The optimum grinding time for the highest Ni upgrade was 0.25 min. The Ni grade increased from 0.88 per cent to 1.35 per cent (upgrade 54 per cent), with 24 per cent Ni recovery. Keywords: fine grinding, stirred media mill, nickel laterite, slurry rheology

Sep 1, 2012

By Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

"There are a variety of methods suitable to analyse elemental and mineralogical contents of rock drill core samples. Current demands are on fast exploration and objective analysis of ore samples. This paper proposes a combination of Laser-Induced Fluorescence (LIF) and image processing, entitled LIF-imaging, as a potential method for automated mineral analysis of the drill core samples. It is shown that LIF-imaging can produce a mineral map of the fluorescent minerals existing on the surface of the drill core samples. The test cases are drill core samples from a Ni-Cu mine situated in Kevitsa, Finland. The main prerequisite of LIF-imaging technique is a reference data, linking colours to the minerals. This study describes the calibration of LIF-imaging technique using precise but slow Raman spectroscopy. Using regularized logistic regression, a model is obtained that classifies the minerals based on their emitted fluorescent colours in the digital images. The abundance of each mineral group is estimated by pixel counting. The results are compared with X-Ray Diffraction laboratory assays performed on the same samples. The results show that the interpretation of the fluorescent minerals through LIF images corresponds to the XRD results. Furthermore, the utilization of the logistic regression to interpret the existing fluorescent minerals greatly improves the technique."

Jan 1, 2014

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018