Search Documents

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By Peter Ay, Vincenz Mehlstaubl, Satyanarayana Narra

"This study gives an insight into non-destructive testing methods suitable for porosity analysis at a small scale, firstly summarizing relevant state-of-the-art technology and pending patents, secondly realizing and documenting the start-up of the VHX-2000 digital microscope by the manufacturer Keyence and thirdly demonstrating practical application with the extended analysis of three fundamentally different agglomerates for which important application-related parameters are determined. Various analysis procedures on the different agglomerates the efficient and timesaving operational features of the digital microscope are outlined. Firstly an analysis of flax fibre agglomerates determines the process conditions best suited to produce agglomerates with specific properties by determining sphericity, cubicity, density and porosity as well as fibre damage and alteration. Secondly the production of iron-hydroxide - hemp-fibre agglomerates serves to obtain information on porosity values as a result of a cauterization of the fibres. The third analysis provides estimations of porosity values for acid-treated lignin agglomerates. Measurements were carried out with compact dry agglomerates and with soaked, expanded agglomerates, determining factors for total water carrying capacity. Practicability of non-destructive testing by digital microscopy is demonstrated and explained concerning the applications in this study by obtaining definite structural findings about the analysed agglomerates. Information on its operation is made available by a practice-oriented manual for the VHX-2000 digital microscope. Further suggestions for more in-detail analysis results with different instruments are given."

Jan 1, 2014

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

By Z. G. Guan

The tungsten ore in Xingluokeng belongs to a symbiotic deposit containing granite and fine vein-type wolframite and scheelite. The tungsten (WO3wolframite) accounts for only 0.233% of the raw ore, 49.60% of the , 49.60% of the scheelite and 0.8% of the tungstite. The dissemination size of the tungsten ore is extremely uneven, with 0.02~1.28 mm for scheelite and 0.01~1.28 mm for wolframite. The dissemination size of scheelite is coarser than that of wolframite. The size of 83% of scheelite and 60% of wolframite is greater than 0.04 mm. The composition of minerals in the ore is quite complex. The major metallic minerals include wolframite, scheelite and pyrite, which are followed by molybdenite, chalcopyrite, arsenopyrite, limonite, magnetite, hematite and siderite. The major gangue minerals include quartz, feldspar, muscovite, biotite and sericite, which are followed by chlorite, fluorite, apatite, dolomite, etc. According to the dissemination features and liberation degree of the tungsten minerals, the technology flowsheet of gravity concentration for coarse particles and flotation for fine particles to re-cover the low-grade and fine vein-type tungsten minerals is adopted, and -0.7 mm is selected as the processing size. The closed-circuit grinding procedure, with the combination of the rod mill and high-frequency vibration screen, is adopted. The grinding product is classified into three products of -0.7 +0.2 mm, -0.2 +0.04 mm and -0.04 mm. The gravity separation is adopted for the former two to recover tungsten minerals and the flotation is adopted for the last one. Under the condition that the raw ore contains 0.23% WO3, some technology indexes of beneficiation have been achieved. The gravity tungsten concentrate contains 63.54% WO3 with the recovery 70.11%. The slime flotation tungsten concentrate contains 35.22% WO3 with the recovery 10.48%. The composite tungsten concentrate contains 57.53% WO3 with the recovery 80.59%. Thus, the tungsten minerals are re-covered effectively.

Jan 1, 2014

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By A. Deepatana

This study compares the use of an aminophosphonate chelating resin Purolite S950 and a sulphonic acid strong cation exchange resin Purolite C160H to recover nickel and cobalt from the synthetic bioleach solutions. Batch adsorption of metal citrate is performed as a function of metal citrate concentration (15~2000 mg/L) and solution pH (0.01M and 0.1M citric acid). The adsorption mechanism as inferred from the fit to Langmuir (LM), Freundlich (FM) and Redlich-Peterson (RP) models demonstrates that nickel citrate adsorbed onto C160H appears monolayer in comparison to that adsorbed onto S950 exists multilayer. In contrast, cobalt citrate adsorption onto both C160H and S950 agrees with the LM model. The results have shown that loading capacities of nickel and cobalt citrate onto C160H are 60 and 65 mg/g whereas those observed onto S950 are 16mg/g and 6 mg/g respectively. These are achieved in metal citrate prepared in 0.1 M citric acid. Resin regeneration is conducted in using 2 M nitric acid solution. The results show high efficiency of nickel and cobalt citrate elution from Purolite C160H. Findings from this study suggest Purolite C160H is a suitable adsorbent for recovering nickel and cobalt from bioleaching solutions.

Jan 1, 2014

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By M. D. Amirova

Cyanide-free technology of complex copper-lead ores flotation may be improved through enlarged range of pH values, enhanced copper recovery into copper concentrates due to additional recovery of secondary copper sulfides, as well as through enhanced efficiency of lead sulfides depression in process of new flotation modifiers-based selective separation. Study of the effects of flotation modifier (of metal nature) on minerals surface conditions proved that the xanthate is practically not adsorbed on the galenite surfaces due to minerals hydrophilization. Joint effects of sodium sulfite and modifier enhance process conditions for intensive galenite depression and at the same time for effective chalcopyrite and chalcosine flotation within a large pH values range (from pH=8 to pH=10). Identified mechanisms carry inference that proposed chemical reagent treating method is very promising for selective copper-lead concentrates separation. Potential use of carbon-containing materials as zinc flotation modifier to enhancing zinc recovery in processes of lead-zinc ores treatment has been studied. In our flotation tests we used Shalkiya (South Kazakhstan) lead-zinc ores containing such impurities as carbon shales, which presence impedes the process of saleable concentrates production and gives rise to excessive consumption of flotation agents due to the xanthate adsorption on the carbon. Lead and zinc concentrates were produced by process stages as follows: ores milled to 95% Cl. -0.074 +0; lead and zinc roughing flotation and further recleaner and testing operations. Test flotation in open process cycle resulted in enhancing zinc recovery into zinc concentrates by 21.1% and increasing zinc content in zinc concentrates by 3.96% that evidences promising potentialities for use of carbon-containing products as additional zinc flotation modifier. Works were carried out under National Program 2003~2005 of fundamental researches ?Physical and Chemical Mechanisms of Interactions in Multicomponent Solid and Liquid Systems Specific for Integrated Processing of Complex Metal-Containing Minerals and Technogenic Raw Materials? and contractual Agreement 2005 Optimization of Production and Technology of Shalkiya Lead-Zinc Ores Processing at Kentau Dressing Works.

Jan 1, 2014

By Xianjun Lu

This paper presents gold occurrence investigations on the altered rock gold deposit from Jiaodong area of China, and comparisons of gold occurrence in the ore samples from different mining levels. According to the results, the chemical and mineral compositions of raw materials from different mining levels are quite similar. However, the relative content and grain size of gold minerals are quite different between the two mining levels of -130m~-340m and -550m~-650m. In the ore of upper mining levels of -130m~-340m, electrum is the dominant gold mineral and accounts for about 80% of the total gold minerals, while native gold is minor and accounts for about 20%. As for the ore of deep mining levels of -550m~-650m, the major gold mineral shifts to native gold which accounts for 67%, while the ratio of electrum drops to about 33%. Coarser gold grain size was observed in the upper mining level ore with a mean size of 33.05µm while the gold grain size was much finer in the ore of deep mining levels with a mean size of 22.85µm. Furthermore, the gold mineral associations also show different patterns between the upper mining level samples and the deep mining level samples. Of the three observed gold association types such as inclusion gold, fissure gold and interparticle gold, more inclusion gold was found in the ore of deep mining levels. The inclusion gold accounts for 62% in the ore of deep mining levels, while that in the ore of upper mining levels accounts for about 56%. Further study revealed that the dominant gold associated minerals are pyrite and sulphides and only a small amount of gold is associated with quartz and silicates. It was shown that the altered rock gold ore from Jiaodong area can be regarded as a free milling gold ore, but the processing parameters should be optimized for the ores in different mining levels according to the different gold occurrence. In addition, it was predicted that enhanced gold liberation is necessary for the ore in deep mining levels.

Sep 1, 2012

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By P. Oliveira, A. Peres, A. Silva

"The decrease in iron content and increase in contaminants grade, associated with greater participation of compact and semi-compact materials, has impacted the recovery of a mechanical cells flotation circuit in the Iron Quadrangle, Brazil. The recovery decrease in the flotation stage motivated the current conventional flotation circuit reevaluation seeking alternatives to restore the recovery, without affecting the final concentrate quality parameters, with low investment. Sampling, chemical characterization of samples, bench scale flotation experiments, and mass balances were conducted. Analysis of the results showed opportunities to improve the circuit performance. The stages prior to the flotation circuit changes were: rougher, cleaner, recleaner and scavenger. In the previous configuration, recleaner was operated as cleaner scavenger and the iron grade in the scavenger concentrate was 23%, representing 38% of the new feed. After the circuit change, the circulating load was reduced from 38% to 15% and the iron content was upgraded to 42%, resulting in increased residence time. The iron content in the global tailings of the concentrator was decreased from 10.9% (year of 2013 average) to 10.2%, representing gains in both mass and metallurgical recoveries.INTRODUCTIONRegarding plant practice, the year 1972 represents a landmark for the concentration of iron ores in Brazil. VALE started up 28 units of WHIMS (wet high intensity magnetic separators) at the Cauê plant in Itabira, each one producing 1x106 t/year of concentrate. Later 17 WHIMS machines were commissioned at Conceição. During the 80’s decade of last century, changes in the ROM required the addition of a cleaner flotation stage to decrease the silica content in the pellet feed.The first company to use reverse cationic flotation as the only concentration operation of iron ore was SAMARCO (start up in 1977). Since 2015 flotation has been utilized at VALE in Itabira as major concentration process, magnetic separation acting as scavenger stage.The Jones matrix type WHIMS were manufactured for decades under patent by KHD Humboldt Wedag. After the expiration of the Jones patent, Eriez Magnetics took the world leadership regarding WHIMS manufacturing. The Brazilian branch of Eriez is Inbras. Based on plant practice experience at the Fabrica concentrator, the Brazilian company Gaustec was established (RIBEIRO and RIBEIRO, 2010) and is now present in different countries. The mega sized WHIMS GHX-1400 (18.000 Gauss, gaps smaller than 1.5 mm) were developed to face the challenge of huge throughput required by iron ore processing (Ribeiro et al, 2017)."

Jan 1, 2018

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Kwan Ho Kim

The beneficiation study of low quality pyrophyllite is conducted to enhance the value of it by selective grinding. In mining stage, the main gangue mineral is quartz, and the content of quartz in ore has an adverse effect on the quality of pyrophyllite. Using the huge difference in hardness between quartz and pyrophyllite, the selective grinding is accomplished using stirred ball mill. As a result, a finer pyrophyllite particle can be easily separated from coarser quartz particle by simple size classification, and the content of Al2O3 of fine particle smaller than 45um increased largely. It means that the pyrophyllite particle is ground selectively compared to the quartz particle, and the quality of pyrophyllite is enhanced.

Sep 1, 2012

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By F. Y. Kang

Graphite with layers structure is easily to form graphite intercalation compounds (GICs) by means of intercalation reactions due to the weak cohesion force among carbon layers, van der Waal?s interactions. By controlling the oxidation-intercalation, high quality exfoliated graphite with low residual sulfur content and MClx-GICs (M=Fe, Co, Ni, Cu, Zn) powder for electromagnetic wave absorbing and shielding materials have been invented. The expansion volume of expandable graphite can be larger than 160 mL/g while the residual sulfur content is less than 800 ppm. The MClx-GICs powder can shield infrared ray and laser completely up to 15 min. We have also in-vented exfoliated graphite for heavy oil adsorption and mild-expansion exfoliated graphite for anode materials in lithium ion battery by controlling the intercalation/de-intercalation. The exfoliated graphite can adsorb heavy oil up to 80 g/g, it also exhibits better performance than commercial active carbon in sewage treatment. The mild-expansion exfoliated graphite as anode material shows high capacity of 370 mAh/g and good cycle performance.

Jan 1, 2014