Search Documents

By N. I. Um

The coal bottom ash generated from coal-fired power plant accounted for approximately 5 mil-lion tons in Korea. Almost all of coal bottom ash was treated as reclamation of the landfill because of the content of unburned carbon. For recycling of coal bottom ash, effective removal of that is required. So, in this study, the removal of unburned carbon by flotation was studied with respect to adsorption ability in surface of a bubble in order to consider its application to recycle the coal bottom ash. The sample A, B and C were that the coal bottom ash contained 2.73%, 7.01% and 10.49% of the unburned carbon (UC) respectively. The column flotation was carried out for each time as the artificial injection of air at 10.0L/min flow rate and the reagents of 500g/ton kerosene and 80g/ton MIBC were used. The samples per water of 1.3 liters were from 0.5% to 4% (w/w.%). In the result of this study, the kinetic curves of unburned carbon adsorption from injected air bubbles were in-creased rapidly as equilibrium was approached; only 5 sec was needed from the sample A and B and 10 sec was from sample C. And the equilibrium isotherms of unburned carbon adsorbed by the infected air bubble from the sample B and C could appear the BET adsorption isotherm; MT = KMEEO/(EO-E)[EO+(K-1)E](K: adsorption affinity), but not the sample A that was not enough to express the adsorption curve.

Jan 1, 2014

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By T. Chmielewski

Unique mineralogical and petrological properties of black shale in the copper ore deposit of the Foresudetic Monocline (SW Poland) resulting from three lithological layers have been described in terms of its unfavorable behavior in the ore processing circuits. A concept of processing of a part of the black shale fraction from the flotation circuit of the concentrating plant by separating a by-product enriched in the shale matter was presented. This by-product represents the tailings of the first cleaning flotation and, as a hard-to-treat circulating middlings, overload the cleaning operation in the flotation circuit. It was found that the investigated by-product cannot be effectively up-graded using standard xanthate flotation. This is due to a fine dissemination of sulfide minerals in the dolomitic and clay shale particles significantly enriched in organic carbon. The content of the organic carbon is similar to that in the petrographically "pure" black shales. After a comprehensive examination of the shale by-product it was recognized that the investigated middlings can be regarded as a specific shale concentrate for individual processing. The effect of non-oxidative leaching of middlings with sulfuric acid on their further flotation was presented. It was shown that non-oxidative leaching is a selective process, in which calcium and magnesium carbonates decomposition leads to effective liberation of sulfide minerals which were finely disseminated in the hydrophilic carbonate gangue. Leaching of the flotation feed with sulfuric acid selectively decomposes carbonate minerals and consequently enhances flotation results. Saturation of leaching slurry with gaseous carbon dioxide favorably creates non-oxidative conditions and leads to a great decrease of the electrochemical potential of sulfide particles as well as hinders their solubilization. Partial carbonates leaching from middlings resulted in evident liberation of valuable minerals. Consequently, it resulted in an increase of both recovery and grade of concentrates obtained by flotation of shale by-product after non-oxidative leaching.

Jan 1, 2014

By Y. D. Gao

A new technique has been developed for comprehensively recovering tantalum niobium tungsten ore by adoption of stage grinding, stage separation, combination of flotation and gravity separation, gravity separation for coarse particles, flotation for fine ones, combination of ore-dressing and hydrometallurgy. The new type and high efficiency combinative collector mainly composed of benzyl hydroxamic acid is firstly used to treat tantalum niobium and tungsten slime, besides the new type equipment for gravitational separation ?YTF-C shaking table for fine particles is adopted to treat flotation rough concentrate, hence having notably enhanced both recovery and concentrate grade of fine tantalum niobium and tungsten minerals. The commercial test obtains the tantalum concentrate assaying Ta2O5 31.98% with recovery 43.44% and tungsten product assaying WO3 89.40% with recovery 76.02%. The developed technique provides a reliable approach and an effective way for comprehensive utilization of lean fine complex refractory tantalum niobium tungsten ore resource.

Jan 1, 2014

Datun Concentrator currently processes complex sulfide ores in Gejiu Municipality, Yunnan Province, China. The ore contains much higher arsenic than other ores. The run of mine ore is fed to the concentrator to recover copper and tin by bulk flotation and gravity concentration, and then the other sulphides, such as pyrite, arsenopyrite, etc. didn?t get utilized and are discarded as tailings due to the high arsenic content. In order to utilize the pyrites in the tailings, a series of tests have been conducted for finding the solution of arsenic removal from high arsenic-bearing pyrite concentrates through simple flotation process. By means of orthogonal experimental design, the optimized levels and main factors have been found out for the roughing stage. Through selection of the effective in-organic depressants for the arsenic-bearing minerals, the arsenic in the pyrite concentrate can be removed to meet the requirement of sulfuric acid plant (As%=0.5%) by the open flotation process, i.e., one-time roughing and two-time cleaning.

Jan 1, 2014

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

In flotation, particulate materials are separated by controlling the hydrophobicity of the particles using appropriate collectors. In this regard, contact angle (?) is the most important process variable. However, the flotation models used in industry today do not include ? as a parameter. As result, flotation circuits are designed based on the first-order flotation rate constants (k) determined from laboratory experiments. A problem with this approach is that laboratory experiments usually give substantially higher k values than achievable in full-scale operations, which makes it difficult to use the model for plant design. In the present work, we have developed a model from first principles using both surface chemistry and hydrodynamic parameters, such as ?, ?-potentials, surface tension (?), particle size, energy dissipation rate, etc. The basic approach is similar to the one developed previously for bubble-particle interactions under laminar flow conditions (Yoon and Mao, J. Colloid and Interface Science, 181, 61, 1996) except that the model parameters have been modified by considering the turbulence in a flotation cell. In addition, the model describes the recovery processes in froth phase, including bubble-coarsening due to coalescence. Based on this model, we have developed a computer simulator (FlotSim) that can be used to design flotation circuits from the mineralogical (or liberation) data on the feed and the hydrodynamic characteristics of a flotation machine. Since the model is dynamic, it can also be used for process control. Further, the simulator has predictive capacity as it is based on a first-principles model. The model-based simulator has been validated in a carefully controlled bench-scale flotation experiments. Keywords: flotation kinetics, flotation model, contact angle,?-potential, size-by-size recovery, liberation, DLVO theory

Sep 1, 2012

Vanadium-titanium magnetite from Panzhihua was crushed with open and closed circuit process by high pressure grinding roller (HPGR). The particle size characteristics of the crushed product were analyzed and the micro-cracks generated by HPGR during the crushing process were studied. The results showed that, in crushed products, the reduction ratio increases and the size distribution becomes more uniform with increasing of the pressure on roller?s surfaces. The fine fraction content of crushing products from -3.2 mm classification closed-circuit by HPGR increases obviously compared with that by Jaw Crusher and particle size distribution is more uniform. Large amount of intra-crystalline cracks and cleavage cracks are generated in vanadium-titanium magnetite crushed by HPGR, which makes the specific surface area larger and Bond grinding work index (objective particle size is 0.074 mm) decreased by 14.05% than that by Jaw Crusher. And the liberation degree of monomer of the product crushed by HPGR increased compared with that by Jaw Crusher with the similar fineness of grinding. Keywords: iron ore, high pressure grinding roller, micro-crack

Sep 1, 2012

New technology for on-line particle size analysis of mineral slurries has opened up new applications for particle size measurement. In some cases the particle size distribution of the final concentrate is an important quality issue. This paper discusses established on-line particle size analysis technologies and presents experiences on the use of a new technique employing laser diffraction in several minerals processing operations. The main innovations in the new instrument are a simple dilution system and multiple scattering correction algorithm, which allows wide solids content variations of diluted sample in the measurement cell. Representative sample for laser measurement is produced by a simple and reliable dilution system. The applications discussed are; Blaine number measurement of Fe concentrate before pelletizing, grinding of variable batches of ore and paste thickener control.

Jan 1, 2014

By L. X. Yu

As is known, the oxidized antimony and antimonate are hard to treat. A new combined mineral processing flowsheet which is controlled in grinding and classification ?bulk floatation?gravity separation is adopted to dispose of gravity-separated tailings (antimony content: 1.48%; oxidization rate: 68.92%) in Muli Antimony Mine, the grade of floatation antimony concentrates is 32.64%; the grade of gravity-separated antimony concentrates is 26.99%; the combined grade of floatation and gravity-separated antimony concentrates is 30.85%, and the total recovery of antimony is 70.64%. Adopting the new mineral processing technique have solved the problem of over grinding of antimony ore by controlling grinding and classification, recovering effectively the sulfide antimony and the easy floatable oxidized antimony of fine size by bulk floatation, recovering effectively the oxidized antimony which is hard to float by classified gravity separation. This is a great breakthrough in the mineral processing technique of the recovery of the oxidized antimony. At present, favorable economic benefit has been obtained from the application of this processing technique in Muli Antimony Mine.

Jan 1, 2014

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014

This article takes the OMRON C200HE PLC for example introducing its application in mica-paper production equipment, including style selection, address assignment of I/O point, and programming for different function. In the transformation process of simulated data and digit data, the corresponding relations between two data and so on are also discussed.

Jan 1, 2014

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By Z. Hu

A complex polymetallic sulfide ore in Yunnan, China, has various valuable minerals, which are Chalcopyrite, Galena, Pyrite, Gold, Silver, and Magnetite. A reasonable new flowsheet with a bulk flotation and a flotation separation of sulfide minerals that are Chalcopyrite, Galena, and Pyrite was carried out at first stage. After that tailings were treated by low intensity magnetic separation to achieve magnetite concentrate. A high Pb concentrate assaying 60.00 percent Pb at total recovery of 75.71 percent with 40.50 g/t Au and 1390.00 g/t Ag, a final high Cu concentrate assaying 24.45 percent Cu at high recovery of 92.03 percent and a magnetite concentrate assaying 60.78 percent Fe at recovery of 33.61 percent with 18.45g/t Au and 234.99 g/t Ag, are obtained. The total recovery of Gold and Silver in Pb concentrate and Cu concentrate reached 71.63 percent and 67.32 percent, respectively. It is shown, that this new flowsheet could realize efficient recovery for all of the valuable minerals in the ore and is easy to be industrialized. Keywords: bulk flotation, magnetic separation, polymetallic sulfide ore, depressant

Sep 1, 2012

By C. Igathinathane

Coal is the most widely used fossil fuel in the world, providing more than 25% of world?s electrical power. Since, the behavior of coal particles in crushing and grinding circuits, concentration operations, and solid-liquid separations is strongly dependent on size, a reliable and accurate measurement of particle size and particle size distribution (PSD) is a vital aspect in coal cleaning. This paper presents a method for the characterization of ground coal particles using image analysis. We utilized a machine vision (MV) approach that used a document scanner as the imaging device and a user-coded ImageJ plug-in that processed the image and automated the PSD analysis and output results in textual and graphical forms. This approach used a sum of volumes (SVolume) as weighting factor for particle length as the primary dimension of analysis and was successfully applied to ground coal. The plug-in was further improved for computational performance in this study. Mechanical sieving (MS) was also used to compare the MV results. MV results showed that the PSD of ground coal followed a uni-modal normal distribution, and the log-normal plot against particle size exhibited a linear trend for most of the range. MS results, however, had three linear segments, when the width-based sieving results were transformed to lengths by applying the shape factor (width/length), but a definite deviation between the PSD plots was observed. This study demonstrates successful application of the MV SVolume approach for PSD analysis of ground coal, which can be extended to similar particulate minerals and products. Keywords: dimension, fiji, image j, image analysis, coal, particle size, plug-in

Sep 1, 2012