Search Documents

By Andrzej Luszczkiewicz, Tomasz Chmielewski, Jan Drzymala, Andrzej Konieczny, Rafal Kaleta

Properties of the sedimentary Polish copper ore mined from the Legnica-Glogow Copper Basin (SW Poland) by KGHM Polish Copper S.A. were presented and currently used beneficiation technologies were described. Due to a unique lithological layered structure of the polymetallic deposit and existing mining system, the ore currently processed in the three KGHM concentrators is very complex with variable content of the carbonate, sandstone and shale fractions. The mined copper ore contains from 0.8 to 1.8 % Cu and Ag, Pb, Zn, Ni, Co, V and Mo as accompanying metals. The paper presents difficulties in upgrading the LGOM ore and selected possible solutions and development concepts of its processing. The first one is a chemical treatment with controlled amount of sulfuric acid of special product of flotation such as for instance middlings. The acid treatment leads to increased liberation of copper minerals and better further processing. Another concept is atmospheric leaching in oxygenated sulfuric acid and ferric ions solution as the major unit operation applied to selected low grade final flotation concentrates or flotation by-products. The third approach, based on copper ore pre-flotation with a frother to partially remove Corg, is also considered.

Jan 1, 2014

By Manisha Singh, Manikanchan Sarkar

"Presently the global steel production is mainly based on iron ore sourced from high grade hematite deposits. India has large deposits of good quality hematite ore but with the prevailing practice, such deposits are depleting fast and getting exhausted. However, apart from such high grade iron ores, India is also endowed with large reserves of low grade iron ore, such as BHQ (Banded Hematite Quartzite), BHJ (Banded Hematite Jasper), BMQ (Banded Magnetite Quartzite) and Magnetite. In the present situation, it has become necessary to focus attention on upgradation of these low grade ores to produce useable concentrate. It augurs well that already substantial investigation work has been carried out in this respect and a few plants have been set up in India and abroad. One important aspect in this regard is the process route options with optimum yield and grade. Some of these low grade ores, particularly magnetite, are found to contain high phosphorous level, removal of which poses a major challenge. Since the grade is low, substantial upgradation necessitates fine grinding for appropriate liberation. Fine grinding is energy intensive and needs attention to achieve economy in this regard. Large quantity of tailings is generated in the process, wet disposal of which gives rise to a lot of hassles and hence, possibility of dry disposal of the same needs to be explored. The experience of the authors, with regard to aforesaid aspects which has been gained in course of carrying out relevant assignments is presented in this paper."

Jan 1, 2014

By Gülay Bulut, Ferihan Göktepe

Pyrite is the most abundant and widespread sulphide mineral and its flotation has been investigated by many researchers. It is well known that, pyrite is floatable under acidic conditions and recovery drops with increase in alkalinity due to changes in solubility of iron hydroxides on the pyrite surface. Most of the works also revealed out that pyrite displays variable behaviour in flotation circuits. This behaviour mainly related with origin and mineralogical composition of ore, liberation size, electrochemical behavior of minerals constituting ore, the trace and minor element content of the mineral, texture, application variables belonging to flotation circuits. In this study, copper activation effect was examined on different origin of pyrites. The experiments were performed with five high grade samples of pyrite from the different mining districts of Turkey. The pyrite samples were different from each other with respect to either their physical or chemical properties; they were different physical appearances and contained different associated minerals. In the micro-flotation tests, 1x10-4 mole/L copper sulphate and 1x10-4 potassium ethyl xanthate were used as flotation reagents. First of all pyrite samples were floated using only xanthate at different pH. Results showed that best floatation results obtained at acidic pH range for all pyrite samples. When copper ions were used to activate, all pyrite samples floated at neutral and basic pH values, too but depending on the samples, recovery and pH ranges were slightly changed.

Jan 1, 2014

By Kilian Neubert, Wotruba. Hermann, Lars Weitkämper

Metallurgical slags are produced in large quantities all around the world as a result of smelting, refining or alloying processes applied to metals, ores and recycling material. The slag phase serves different purposes in metallurgical processes. It prevents heat losses and protects the metal phases from contaminations and absorbs gangue and extracted impurities. Due to achievable metallurgical efficiencies certain amounts of valuable metal contents always remain in the residual slag. Recycling of these metallurgical slags has several positive effects, such as optimized ecological and economical compliance of the producing industry. If recycled metal contents can be reintroduced into existing processes, required inputs of raw material can be lowered. High metal prices enable the economic recovery of metal contents in metallurgical slags by applying different non-metallurgical processing methods. Conventional processing of metallurgical slags utilizes processes such as hand picking, selective comminution, screening and magnetic separation. Those state of the art processing techniques have limitations in terms of achievable metal recoveries and required energy demand. The approach for an optimized processing of metallurgical slags targets enhanced metal recoveries in combination with lower specific treatment costs. Processes such as coarse and ultrafine density separation, as well as sensor-based sorting as a pre-concentration stage are used to enable an efficient recovery of metal contents in slags. By applying these methods a completely dry working process is possible. This paper reviews the commonly used methods and describes approaches for innovative processing of metallurgical slags to enhance metal recoveries. Focus of this paper is laid on sensor-based sorting as well as on processes for dry density separation.

Jan 1, 2014

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By A. Collings, A. Farmer

Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation. This effect may be utilised in lowering the level of iron contamination in silica sand used for glass making, in improving the sharpness of electrostatic separation of heavy mineral concentrates, in shortening the time of leaching of minerals and in improving the selectivity and recovery of flotation processes. Parameters affecting the efficiency of these processes, such as input power and levels of reagent addition, are discussed. In particular, we present data showing the relationship between power input and the particle size of surface coatings removed, which can be explained by the Derjaguin approximation for the energy of interaction between a sphere and a flat surface. Pilot scale studies, using commercially available components, are currently being used to assess process viability and will be compared with laboratory scale results.

Jan 1, 2003

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By Markus Dammers, Christopher Robben, Hermann Wotruba, Christian Schropp

"In most underground mining processes the entire extracted ore is transported from underground workings to surface processing plants for separation of valuable minerals and gangue material. Most of the transported material consists of barren rock with negligible metal content, especially for low grade deposits, such as in the copper or gold metal ore mining. Increasing mining depths result in higher costs for transportation and hoisting. Therefore, rejecting waste rock as soon as possible from the material stream gains importance. The concept of resource to product integration in the form of earliest waste rejection in combination with subsequent backfilling follows the philosophy of ‚leaving waste underground?. Implementing mineral processing underground can lead to less required mass movement to surface, hence reducing transportation and hoisting costs. At the same time, rejected waste can be used as backfill to increase extraction rates by reducing pillar volumes. In the mill, a stable high grade feed leads to decreased specific operating and investment costs as well as increased productivity and recovery. These effects as a whole have a large potential to reduce cut-off grades so that resources can be turned into reserves. Within the I²Mine (Innovative Technologies and Concepts for the Intelligent Deep Mine of the Future) project of the European FP7, investigations are carried out by the Unit of Mineral Processing of RWTH Aachen University, the Institute of Mining Engineering I and TOMRA Sorting Solutions | Mining. One aim of the cooperation is to develop new concepts for a comprehensive integration of near-to-face processing in combination with backfill into the overall underground mining process. Effects on up-, down- and side-streams are investigated to prove the potential of resource to product integration in comparison to common underground mining systems and processing methods."

Jan 1, 2014

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

The optimal design of flotation circuits is a complex task as the mathematical model is nonconvex and includes binary variables, making it difficult to obtain the global optimum solution. Furthermore, there are epistemic uncertainties in the evaluation of the performance of flotation and grinding units. This epistemic uncertainty is generated because semi-empirical models are used with parameters that are a function of the circuit design. Therefore, it is not possible to adjust these models based on experimental data as the experimental conditions are not known at the design stage. This paper analyzed the effect of the uncertainties in flotation units, grinding units, and both units simultaneously. As a result, this paper demonstrated that, for a specific mineral, few structures exist that are optimal for a wide range of values in flotation stage recoveries and liberation fractions in the grinding units. A remarkable aspect of this work is that it introduces grinding, one of the operations that most influences energy consumption in mining and has not been studied in depth in the design of flotation circuits. To demonstrate that there are few optimal structures for a specific mineral when there is high uncertainty in the process units, an a priori approach or first principles was used. Two methods of proof were used: proof by construction and proof by exhaustion. Proof by construction is the construction of a concrete example with a property to demonstrate that something having that property exists. In this work, two examples were considered in the proof by construction. In proof by exhaustion, the conclusion was established by dividing it into a finite number of cases and proving each one separately. Here, 30,000 cases were included for each example. This knowledge can be useful in circuit design including grinding, e.g., after selecting the circuit (or the most promising circuits), and the equipment design parameters and operating conditions can be defined based on simulation and laboratory tests.

Jan 1, 2018