Search Documents

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Roberto A. Lopez, Eric Lindquist, Jon Bussiere, Dean Iwasa

"The new 11-story U.S. Federal Courthouse building in downtown Los Angeles demanded a cost effective foundation system capable of attaining a strict total settlement criterion of 0.5 inches (12 mm) under high applied loads. A design-build ground improvement system consisting of 3 ft (0.9 m) and 7 ft (2.1 m) diameter deep soil mix (DSM) columns embedded into the relatively soft Fernando Formation bedrock was selected for the project. The DSM columns support applied stresses of up to 8,800 psf from four large concrete core elements that transfer concentrated building loads to a 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat. The soil mixing ground improvement solution provided flexibility by allowing installation of the DSM columns around existing belled caissons left in place from prior structures, and by allowing repositioning of some of the DSM columns to avoid other existing obstructions in the fill. DSM spoils were used to construct a 2 ft (0.6 m) thick load transfer platform on top of the DSM columns. Quality control measures included utilizing equipment outfitted with automated data acquisition systems, performing three full scale load tests, performing daily wet-mix sampling and compression testing, performing full-depth coring and unconfined compression testing on core samples, and using a borehole acoustic televiewer to evaluate the uniformity of the DSM columns where core recovery was problematic. The results of subsurface investigation and the load tests were used to develop 3-dimensional finite differences models for evaluating stress distribution and deformation of the foundation system.INTRODUCTIONThe new U.S. Federal Courthouse building is currently under construction in downtown Los Angeles, California. The new courthouse will be 11 stories tall with one partial below-grade B1 basement level. The building will have four structural core elements that extend from the main building foundation at the B1 level to the top of the structure. The majority of the building loads will be transferred through the structural core elements to a new 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat beneath the central portion of the structure. The foundation pressures beneath each of the core element locations will be approximately 6,200 to 8,800 psf (300 to 420 kPa) with lower foundation pressures at locations farther away from the central core area."

Jan 1, 2015

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor&apos;s design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Gisele R. Passalacqua, Taylor Malangone, Subhash Mahali

New York City is a busy metropolis with 8 million people. New York has the largest public transportation system with 6 million riders a day throughout the subway system. Keeping this infrastructure in service is vital to the overall economy of the region. Hurricane Sandy proved to have a devastating impact on infrastructure in Metropolitan New York. New York City Transit is on the forefront to provide resiliency and maintain its facilities with the use of flood protection systems. This paper presents flood protection structures utilized at Hammels Wye substation site in Far Rockaway, Queens, New York. The site is in close proximity and surrounded by water. The subsurface conditions consist of loose silts overlain by medium dense glacial sand. The high groundwater level combined with limited access to the site presented challenges. A flood protection system consisting of flood walls was recommended for this site. In certain areas the flood walls consisted of retaining walls supported on micropiles. For other areas, the flood walls consisted of steel sheet piles with jet grout columns to reduce seepage below the walls. The effect of driving sheet piles with vibratory hammers on nearby existing structures is always a concern. Recently, hydraulic hammers with variable moment/frequency are being considered as a mean to reduce vibration effects during driving. In this project, an instrumentation testing program was performed to measure peak particle velocity during sheet pile driving utilizing the variable moment vibratory hammer. Plots of peak particle velocity versus frequency were generated. This paper will present the design aspects of the flood walls and construction challenges during installation. This will prove beneficial to engineers in both design and construction fields.

Sep 8, 2021

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021