Search Documents

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By Yan Lap J. Kan

"A waterfront stabilization system consisting of Deep Soil Mixing (DSM) columns, vinyl sheet pile fascia, and concrete flood walls supported on shallow footings was designed and constructed for a high-density waterfront development in Northern California. The project site is underlain by soft, compressible organic soil locally known as Bay Mud that has been capped with loose sand and imported fill. The waterfront stabilization system constructed at the site mitigates liquefaction, consolidation settlement and seismic potential slope deformation along the waterfront; the system was designed to reduce lateral displacements to tolerable amounts for the proposed structures. This paper presents the general design methodologies, construction challenges and quality control of this waterfront stabilization system.INTRODUCTIONUrban development in Northern California is fueling innovations in geotechnical engineering as more complex sites are developed. ENGEO Incorporated introduced a deep soil mixing technology from Japan to the US and designed a waterfront stabilization system for a high density waterfront development project in Redwood City, California. The approximately 12½-acre project site, as shown on Fig. 1, is surrounded by water on three sides, with an inner marina at the center of the site.The project site is located in the seismically active San Francisco Bay Area in California. The San Andreas Fault, the Monte Vista-Shannon Fault, the Hayward Fault and the San Gregorio Fault are major active faults located within 25 miles of the site. Once a former marshland with a major slough until the late 1950s, the site was reclaimed by placing imported fill over the native compressible clay deposits, locally known as Bay Mud."

Jan 1, 2016

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Dennis Nottingham

The need for deep compaction of submerged granular soils has led to improvements in this area. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100 foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers? experiments, observations and measurements, led to an ?H? pile probe design which has produced measured soil density improvements up to 250% using SPT ?N60? values as a measure.

Jan 1, 2013

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Willie M. NeSmith

The use of drilled (screwed) displacement piles is an emerging sector of the United States deep foundation industry. During installation of these systems, a Ko to Kp environment is created in the materials surrounding the pile immediately prior to casting, and this condition results in increased shaft and toe resistance in soils where displacement leads to densification. Current continuous flight auger and drilled shaft design methodologies in the United States assume a Ko to Ka condition in the vicinity of the pile, and are thus an inappropriate starting point for static capacity analysis of drilled displacement piles. This paper examines constructability issues, and the sensitivity of performance to installation, and offers an empirical design methodology for drilled displacement piles. The proposed design process has been based on evaluation of 40 load tests, primarily in granular materials, and in a variety of geologic settings, and includes modification for soil types within the coarse-grained range.

Jan 1, 2002

By R. Paul De Bruyn

A. Crane Check List -- Make -- Model -- Year of Manufacture -- Where is load chart? Is it for this crane? -- Boom style and length -- Boom tip drawing (sketch) for fixed lead connection. Has the crane manufacturer been consulted on the point of attachment? -- How many drums; diameter and length of wire rope. -- Is the single part line pull enough to lift pile or hammer on single part line? -- What is the effective weight of the whole driving system - leads, pile, hammer, etc? -- Are there any auxilliary hydraulic systems? Are the line pulls on these adequate to lift the pile or hammer? -- What is the anticipated working radius? Will the spotter collapse to that length? -- Nature of foundation under crane - barge, marsh, unstable sand, etc. -- Does the crane meet OSAH and state regulations -current certification. Note - the operator is responsible for compliance with regulations. -- Is there any extra weight added to counterweight by compressors or hydraulic systems? What does crane manufacturer say? Consult factory before adding.

Jan 1, 1990

By Samer Rabab’ah, John C. Niedzielski, Jason Valeria

The PHX Sky Train is an automated people mover system located at Phoenix Sky Harbor International Airport. Phase II of the PHX Sky Train includes the design of over 150 drilled shafts for support of four guideway abutments, 75 guideway piers and three proposed stations. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the elevated guideway above the ground surface, where it needs to pass over roadways, parking lots, an existing terminal, and other buildings. Deep foundation design involves designing drilled shafts within the SGC deposits, some of which extend below the long-term groundwater table. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the project. This paper will present the results of a drilled shaft load test program implemented to provide site-specific measurement of the axial and lateral performance of the project drilled shafts. The load testing program consisted of a bi-directional load cell axial load test and a lateral load test performed on an instrumented test shaft 84 inches in diameter. The development and execution of the load test program and analysis of the test results are discussed. Comparisons were developed between predicted load capacities of drilled shafts using different design methodologies and the load capacity measured from the load tests. The load test results showed that underestimation of the capacity is evident using conventional methodologies. The load testing program was important for verifying the performance of the drilled shaft foundations on the project and was used to reduce the size of the drilled shafts. INTRODUCTION The PHX Sky Train is a five-mile long automated people mover system situated at-grade and on an elevated guideway which connects terminals, parking facilities, a rental car center and the Valley Metro Light Rail system in Phoenix. The purpose of this automated train system is to provide a secondary transportation system within the airport to relieve roadway congestion, minimize wait times and travel times for passengers and provide climate-controlled waiting areas. Phase 1 opened to the public on April 8, 2013. Phase 1A opened on December 8, 2014.

Jan 1, 2019

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let's say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By Chris L. Powell, Russell J. Denny.

"The remotely located Cockatoo Island iron ore mine off the Kimberly coast in Western Australia, which has been in operation since 1951, was recently expanded up to 50m below sea-level using staged construction of a rock-filled seawall around the open cut mining operation. The most recent stage of the seawall expansion required a seepage reducing cut-off barrier to be installed through the seawall into underlying seabed sediments. A line of grout holes at 1m centres was proposed to form the seepage barrier, with grouting extending 17m below the top of the seawall. Top hammer drilling techniques were used to penetrate the 12m deep rockfill to seabed level, and permeation grouting carried out within the rockfill to fill voids and stabilise material around grout holes. The local 10m tides meant that tidal washout of fines and grout would be a major risk, and so a combination of cementitious and chemical grout was used to create rapid gel times. Following permeation grouting, holes were re-opened to allow jet grouting to hydraulically mix and grout permeable seabed sediments below the seawall. Using the duplex jet grout system in a single pass to 17m below platform level, the jet grouting was extended upwards into the seawall fill itself to overlap with the earlier permeation grouting. Finally a soil/cement mixed capping trench was installed using slurry trenching techniques with soil/cement/bentonite mixed backfill in order to complete the grout treatment. The approach taken allowed considerable onsite flexibility in technique. An automated slurry batching plant allowed adjustment of mixes to suit the varying subsurface conditions which were encountered during the works.IntroductionLate in 2013 Wagstaff Piling was engaged to install a seepage barrier through a rockfilled seawall built to allow expansion of sub-sea iron ore mining operations on Cockatoo Island off the remote Kimberley coast in the North West of Western Australia. Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of sub-sea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansion stages that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative grout curtain seepage barrier solution was selected to ultimately provide the necessary cut-off to allow access to high grade ore, while protecting the mine from inundation by the sea."

Jan 1, 2016

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016