Search Documents

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By Adam Wright

"Les Mines Selbaie have been producing copper and zinc concentrates from the A-1 ore zone since 1986. This paper reviews major developments in flotation practice over that period. Firstly, ore blending strategies for Selbaie's non-homogeneous polymetallic ore are discussed. The evolution of reagent use is then reviewed, focussing on copper collector trials. A description of Selbaie's flotation columns follows. Finally, past and future developments for process control are outlined.Depuis 1986, Les Mines Selbaie produisent du concentré de cuivre et de zinc provenant de la zone A-1. Cette conférence présente !es développements majeurs en flottation qui ont eu lieu depuis ce temps. Premièrement, la stratégie du mélange de minerai non homogène polymétallique est présentée. L'évolution des réactifs utilises est démontrée, particulièrement !es collecteurs de cuivre. Par la suite !es colonnes de flottation sont presénteés et finalement !es développements futurs ainsi que ceux qui ont eu lieu dans le contrille de procédé sont expliqués.1.0 INTRODUCTIONLes Mines Selbaie, wholly owned by Billiton Metals Canada Inc., is currently mining and processing ore from a polymetallic surface deposit located 288 km northwest of Val D'or, Quebec (fig. 1). The mine produces copper concentrates containing gold and silver as well as zinc concentrates containing silver. 8000 dmt/day of ore is crushed and ground to 80% passing 49 µm, prior to processing by conventional copper/zinc differential flotation. The flotation circuits consist of both conventional and column cells (fig. 2). Detailed descriptions of the mill are available elsewhere in the literature (8,9)."

Jan 1, 1995

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By L. Lariviere, M. Grenier, R. Khalili, D. Shook

A mineral processing facility near Montreal, CEZinc, Noranda Inc., has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions.The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation.The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views.The paper will discuss the solution architecture and the improvements the IT, operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

Jan 1, 2003

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By Mario Morin

The application of underground pre-concentration technology to narrow vein mining has the potential to change the entire economics of bulk mining methods when used in narrow vein situations. The rejection of waste at or near the face means that a higher-grade ore can be sent to surface. The waste rock can be reused directly as backfill. Swelling of the muck through blasting means that only 60 to 65% can be used as fill. Planning and scheduling of the fill usage is key to the success of this method. Through the use of simulation and system analysis, this paper examines the planning and scheduling implications of underground pre-concentration when applied to traditional narrow vein mining methods (cut-and-fill /drift-and-fill, longhole, AVOCA). It considers the logistical factors that represent potential system bottlenecks that are key to understanding the correct implementation and control strategies.

Oct 1, 2004

By Claude Dufresne

The technical development of the niobium-bearing products is to a great extent influenced by the striving of the respective industries to maintain or strengthen their positions in all fields of application against competing materials. South East Asia, China, Eastern Europe and CIS are slowly becoming significant consumers of ferroniobium. As a result, the world niobium market has been stable despite the slowdown in steel production in 2001. This paper will describe present producers, capacities and the current market conditions.

May 1, 2003

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994