Search Documents

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979

By Yuki Soma, Tsutomu Ogawa, Jae Hyung Hong, Toshihiro Nagato

The Saganoseki flash furnace was built in 1973. The steel frames of the flash furnace were designed to absorb the expansion of refractories and contain expansion-absorbing materials between their frames and the skin plate. Expansion and deformation resulted in the furnace settler because of the repeated increase and decrease in temperature from more than 30 maintenance shutdowns. Preliminary investigations were conducted to confirm the condition of the settler, and it was found that partial cracks accompanied the expansion in the lower layer of the refractories. As a result, the risk of molten-matte leakage increased. Based on the above investigation, it was decided that the entire settler should be replaced by introducing a spring-displacement structure that was capable of maintaining the furnace integrity over an extended period. The difficult redesign and rebuilding of the Saganoseki flash furnace was accomplished successfully and safely in 76 days from September to December 2017, as planned. Because of various redesigns, the furnace was changed to a flash-smelting furnace that can withstand higher thermal loads based on recent trends of copper concentrate with increased sulfur and reduced copper. The new furnace is operating smoothly at present. INTRODUCTION The flash-smelting furnace of Pan Pacific Copper Co., Ltd. Saganoseki Smelting & Refinary commenced operation in 1973, with an original designed feeding rate of 71 t/h. As a result of facility remodeling and operational improvements, shown in Figure 1, the feeding rate was increased to 215 t/h in recent years. After more than 40 years of operation, the original settler in the melt holding section of the flash furnace underwent significant expansion and deformation.

Jan 1, 2019

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By Robert B. Parsons

"The mining industry is adjusting its sights to take a shot at the rising level of non-profit taxes which threaten to handicap the industry 's competitive advantage. In the case of this particular expedition, the industry evidentally has a strong ally - the country's mines ministers. It appears that an initiative is under way to assess the impact of non-profit taxes on mining in Canada as compared to other mining nations.IntroductionSeventy-five years ago, Canadians were unceremoniously introduced to something called income tax. Since then, income tax has been identified as the source of countless evils ranging from the common cold (attributed to stress) to the demise of the economy. Some years later, the provinces jumped on the bandwagon with their own income taxes, and later on with mining taxes. These profit-based taxes had some appeal to elected officials and to a segment of the populace. The onus of the taxes varied directly with the ability to pay (in theory, at least). Previously, the principal sources of government revenues had been property taxes and customs duties, which were viewed as possibly being somewhat regressive in nature.The mining industry has always had concerns about different aspects of income and mining taxes - the tax rate is too high or the depreciation rate is too low, and so on. Recently, though, the industry has turned its sights on the expanding array of taxes which are not based on profit, including payroll taxes, capital taxes, water taxes, sales taxes, fuel taxes, property taxes, environmental levies and user fees. The industry is seriously concerned that the rising level of non-pro fit-based taxes is not only hampering the industry 's ability to reinvest in Canada, but is also placing Canada at a disadvantage in terms of trying to attract new investment capital."

Jan 1, 1992

By Klau Meyer

"At Teck-Corona Operating Corporation's David Bell Mine, a successful water quality management strategy has been established. This resulted from the development and application of process technology, allowing year round discharge of an effluent exceeding the chemical and biological standards set by the Ministry of Environment. This strategy aims at minimizing contaminant levels of effluents through optimization of reagent selection and reduction of effluent volumes through maximizing reclaim water usage. Concentrator and effluent treatment plant operating practices, process chemistry and the results of the water quality management strategy are reviewed.IntroductionThe David Bell Mine is located in the Hemlo gold camp 42 km east of Marathon, Ontario. The concentrator has a design throughput of 1000 tonnes per day. The processing of the run of mine ore ( - 15cm) involves the following unit operations: grinding in a semi-autogenous mill followed by a ball mill, thickening, pre-oxidation , cyanidation, and carbon-in-pulp gold recovery followed by electrowinning and refining.The David Bell Mine water quality management strategy is composed of the following items (Goodfellow and Meyer, 1991):• natural destruction of cyanide contained in the tailing water in a large shallow tailing pond ;• preliminary treatment of reclaim water in the grinding circuit for cyanide and heavy metal removal;• pre-oxidation of sulphide minerals in pipe reactors to reduce cyanide consumption using pure oxygen;• pH control in the grinding, pre-aeration and leach circuits to minimize the dissolution of stibnite while maximizing gold recovery; • close control of cyanide addition rates to the leach circuit to maintain the lowest possible levels;• a carbon column for gold recovery;• an effluent treatment plant for antimony and heavy metal removal; and• the use of final treated effluent for industrial water underground to minimize fresh water consumption."

Jan 1, 1992

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By Dale L. McKinnon, Jean-Pierre Farant

"Dust collectors are used to reduce airborne dust levels generated during crushing at a mining operation and their adequate maintenance is required to ensure effective control of health and safety hazards associated with dusty conditions. Although the pitot traverse technique is commonly employed to balance these dust collectors, the use of an alternative-the equilibrium concentration tracer gas method-is proposed in this paper. This method, which uses sulphur hexafluoride as a tracer gas, can be used to balance airflows in dust collectors and to determine hood collection efficiency accurately and effectively. This technique also reduces some of the errors inherent to pitot tube measurements. IntroductionIndustrial dust collectors are used to reduce dust genera ted by processes like cru shin g, and these must be periodically checked and balanced to ensure continuing effective control of health and safety hazards associated with dusty conditions.To date, the pitot tub e traverse technique has been commonly used to balance air flows in dust collectors. However, this technique is both time -consuming and cumbersome. The equilibrium concentration tracer gas method, described in this paper, is proposed as a viable alternative as it is faster, more reliable, and amenable to automation. The use of tracer gases for such task s is not new. This approach has been used in a variety of mining situations to determine volumetric flow rates in underground openings, leak age through mine stoppings, the effectiveness of face ventilation, pollution migration patterns, mine air recirculation rates, and rock porosity."

Jan 1, 1986

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By J. Lu, D. B. Dreisinger, G. Houlachi

"Zinc metal is primarily produced by electrowinning from sulfate solution. Zinc electrowinning is very sensitive to impurities such as Co and Ni. These impurities have to be removed to produce high-quality zinc and maintain a high zinc current efficiency. Zinc dusts are used to remove these impurities by cementation. However cobalt cementation is extremely slow and it is typically activated by the addition of Cu and Sb. Even with the use of Cu-Sb activation, cobalt is still difficult to remove. The zinc dust used for cobalt cementation is negligible compared to that consumed for hydrogen evolution. In some plants up to 6-7% of electrolytic zinc is used for cementation. This is a great waste of energy. Cu-Sb activation is not well understood. The objective of this study was to further understand the Cu-Sb activation and then find a way to reduce hydrogen evolution and promote cobalt cementation. The investigation reveals how hydrogen evolution (or zinc dissolution) and cobalt cementation and re-dissolution change with temperature, zinc dust dosage, the concentrations of copper and antimony and time. In the Cu-Sb activation, copper is deposited on a zinc particle to produce a porous shell. The zinc particle as an anode dissolves while the shell as a cathode provides a place where cobalt cementation and hydrogen evolution occur and they are catalyzed by antimony. A certain level of antimony (around 0.1 mg/L) is a key to maintain the catalytic effect of the shell. At a higher antimony concentration, cobalt cementation is accelerated slightly while hydrogen evolution is increased greatly. When a zinc particle dissolves to a certain degree, cobalt loses its cathodic protection and starts to re-dissolve. The change in cobalt concentration is determined by the rates of cobalt cementation and re-dissolution. The operation conditions can be optimized to maximize the cobalt removal and minimize the zinc dust dosage.INTRODUCTIONMost of the world’s zinc metal is produced by electrowinning from sulfate media. Many impurities such as iron, copper, cobalt and nickel are co-extracted into solution with zinc. Iron, mercury, indium, lead and tin are removed by co-precipitation as hydroxides. Copper, nickel, cobalt, aluminum, arsenic and germanium are partially co-precipitated with iron while cadmium, magnesium and chloride remain in solution. Cobalt, copper, cadmium, nickel and etc. are subsequently removed by cementation with zinc dust to achieve an acceptable current efficiency and high purity metal product for the economical production of zinc. Zinc provides a strong thermodynamic driving force for the cobalt cementation:"

Jan 1, 2016

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By G. Lafont

Aug 1, 2013

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By I. C. Edwards, D. C. Smith

THE milling plant of Bicroft Uranium Mines Limited at Ban-croft, Ontario, was one of the first in Canada to employ ion excl1ange for the selecti1•e recovery of uranium from acid leach liquors. The ion ex-change circuit started operating early in November, 1956, and by June 1 I959, had handled more than two million tons of pregnant solution containing I,830,000 pounds of U3Os. Each column had been saturated and eluted about 430 times. The ion exchange columns are the conventional fixed bed type. Uranium is eluted from the resin with a sodium chloride-sulphuric acid solution and is precipitated continuous-ly with magnesia. After filtering and drying, the precipitate, or "yellow cake," is packaged in drums for shipment to the refinery.

Jan 1, 1962

By K. V. Konigsmann

"Concentrate dewatering operations have a significant influence on the economics of base metal beneficiation. The expenditures f or energy and labour per tonne of product are high. The relatively low efficiencies of standard techniques present inducements for process modifications. Development efforts at several Noranda concentrators led to process changes which improved productivity, namely, agitated pulp storage in large vessels, process automation and pressure filtration.IntroductionA program was initiated in 1968 with the aim of improving utilization of manpower and equipment in dewatering operations. The following considerations motivated us in this effort: Firstly, filters and dryers had traditionally been operated continuously and in step with grinding and flotation circuits. The demand for labour and equipment operating time was fixed and was not determined by the rate of concentrate production.Secondly, dewatering equipment had usually been designed to handle the concentrate tonnages which were produced when mill feed grades were high; therefore the equipment operated at less than capacity when treating ores of average metal content. The first goal was the separation of the flotation process from concentrate dewatering by development of a practical storage system for concentrate pulps . A second objective was the gradual introduction of dependable automatic controls. The steep increase in energy costs after 1973 added urgency to the search for dewatering processes which were highly energy efficient."

Jan 1, 1984

By David Rahal, Saul Ortiz, Maria Escobedo

The general trend in the minerals industry is towards the processing of fine grained, disseminated mineral deposits. This has led to an increase in the number of fine/ultra-fine grinding installations using stirred media mills. The challenge is that both the equipment type and the mineralogy of the deposit have an effect on specific energy consumption. Fresnillo PLC recognized this issue and addressed it by providing samples for testing in a laboratory regrind system. The objective of the test program was to determine the specific energy required to achieve a product size of 10 µm (P80). A specific energy plot was generated for both a lead and zinc flotation concentrate. It indicated that 34 kWh/t and 51 kWh/t were required for the two samples (Pb and Zn respectively). This difference highlights the effect of mineralogy on the energy required for fine grinding. The regrind feed and products were submitted to a range of basic mineralogy tests to quantify the mineral differences that could have changed the specific energy requirements. These tests provided general mineralogy, documented optical textures, and provided particle size microscopy. The lead concentrate was found to contain significant amounts of silicates in addition to the dominant sulphide, pyrite. The zinc concentrate was determined to be mostly sphalerite with minor amounts of quartz, chalcopyrite, pyrite and galena. The material testing results illustrate the importance of basic mineralogy studies in conjunction with comminution testing to determine specific energy consumption.

Jan 1, 2016

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By M. Soleimanifar

With more and more industrial construction projects implementing RFID and other sensor-based technologies on fabrication and project sites, new innovative processes are needed to help automatically read and re-position RFID tags while reducing the cost to deploy RFID infrastructure over large areas. RFID tags are being used on construction sites to help identify the location of materials, equipment and personnel to aid in finding project critical materials and equipment required to construct the industrial facility on time and on budget. This research provides a cost-effective process for reading tens of thousands of RFID tags over large project sites from outdoor laydown yards, to warehouses to the workface where the materials and tagged equipment are installed. Based on the collected RFID and sensor data, localization mechanisms determine the most recent coordinates of the tagged components. The paper will cover analysis of RFID collected data and key lessons learned from a commercial deployment of the SiteSense® system with one Alberta-based industrial contractor, JV Driver Fabricators, at an 80-Acre module, pipe spool and structural steel fabrication site.

Aug 1, 2013

"In the past year, mining at the Doyon Mine has shifted entirely from open pit to underground. The mine produced 234 692 ounces of gold in 1989 and is expected to produce 225000 ounces in 1990. The Doyon Mill has been running slightly above design capacity, and recovery has increased 3%.IntroductionThe Doyon Mine is located 25 miles east of Rouyn-Noranda, Quebec (Figure I).It is a joint venture owned by Lac Minerals and Cambior, with each holding a 50% interest. Lac Minerals operates the mine under the direction of a management committee.Production at the Doyon Mine began in 1980 with the start up of the Main Zone pit. Shortly thereafter the Doyon Mine became the largest open pit gold producer in Canada.In 1983, a ramp leading to the fourth level and exploration drifts were driven. Results were very encouraging, therefore the decision was made to sink a 2150-foot deep shaft, which was completed in 1986.In mid-1986, production began in the West pit, while underground mining of the West Zone started shortly thereafter, at the end of the same year.In 1987 the mill capacity was increased to 3300 tons per day and the Main Zone underground operations commenced."

Jan 1, 1990