Search Documents

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By Doug Ashbury

Diamond Miners? Challenges ? Remote ? 300 kilometres from Yellowknife ? Sub-Arctic conditions ? permafrost, climate ? No power ? No all-weather roads ? Ore bodies difficult to find ? Caribou, fish of special concern ? Communities with low education, little experience, but high expectations ? Major investment required ? Diavik C$1.3 billion

Apr 1, 2005

By Jehan Rondot

Des quartzites très pars ont été dêcouverts au cours de la cartographie de la region du lac des Martres, étape de l'étude géologique de la region de Charlevoix. On distingue quatre groupes métasédimentaires, tons con tenant des niveaux de quartzite dans an moins deux domaines géologiques différents, c'est à l'ouest, clans le domaine gneisso-charnockitique que se situent les quartzites du groupe des Martres. Quartzite et gneiss à grenat et sillimanite, en banes épais, constituent la formation de La Galette. A Pest, dans un environnement gneisso-granitique, les deux groupes métasédimentaires de Saint-Siméon, et de La Malbaie comprennent, par contraste, des bancs pen épais et de compositions variées. Les niveaux de quartzite dépassent rarement 50 m d'épaisseur. L'autre groupe metasédimentaire, celui de Saint-Tite des Caps, recoupé de nombreuses intrusions charnockitiques et granitiques, ne possède que de minces niveaux de quartzite. La pureté et la grande épaisseur des quartzites de La Galette suppose une histoire complexe qui se termine par des depots continentaux de climat aride, par opposition aux depots marins des autres groupes. D'autre part, la presence de ces quartzites an sein de roches Presque anhy¬dres et de haute temperature que sont les charnockites leur confère des caractéristiques de fusion sans decrepitation. Parmi la multitude de depots de quartzite qui existe clans le monde, peu sont de qualité supérieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement à ceux des meilleurs gisements des Etats-Unis, de l'Europe de l'Ouest et de l'Afrique du Sud. D'accès facile pour l'exploitation, les gisements ne sont qu'à une trentaine de milles de Baie Saint-Paul ou de La Malbaie, sur le Saint-Laurent. L'utilisation en metallurgic prévue pour le quartzite de La Galette comprend la production de silicium, de ferro¬silicium et d'autres alliages de silicium. La composition du quartzite est en outre appropriée pour la production de carbure de silicium et de silicate de sodium. Les fines peu¬vent être utilisées pour la fabrication du verre et comme matière de charge.

Jan 1, 1977

New Millennium Capital Corp. shall not be liable or responsible for any claim or damage, direct or indirect, special or consequential, incurred by the user arising out of the interpretation, reliance upon or other use of the information. Users should not rely on information for any purpose other than for gaining general knowledge of New Millennium Capital Corp. Although New Millennium Capital Corp. believes that its expectations reflected in these forward-looking statements are reasonable, such statements involve risks and uncertainties and no assurance can be given that actual results will be consistent with these forward-looking statements.

May 1, 2011

By E. Wright

"INTRODUCTIONThe Ruttan Mine is located twenty-two km east of Leaf Rapids in northwestern Manitoba. The copper-zinc exhalative massive sulphide deposit is comprised of a series of individual and interconnected en echelon lenses which strike east 20 degrees north and dip south 70 degrees. The mine has been owned and operated by the Hudson Bay Mining & Smelting Company since July 1987. Sherritt Gordon Mines Limited began mining the orebody in 1973 from an open pit, but production has been entirely from underground since 1980. HistoryDuring the progression from open pit to underground mining, it was recognized that manual methods of ore reserve calculation were inadequate for responding to changing metal prices and evaluating alternative mine plans. The mine planning system that was developed is described in the paper, ""Computerization of Ore Reserves and Mine Planning Functions at Ruttan Mine"", presented by B.C.W. Haystead at the 1984CIM Annual General Meeting. At that time, programs for core logging, diamond drill hole plotting, grade interpolation, ore outline digitizing, and reporting had been developed by the Systems Department for use on Sherritt's UNIVAC 1100 mainframe computer. Telecommunications linked terminals at the Ruttan coreshack and office to the UNIVAC in Fort Saskatchewan, Alberta. The same mine planning system was also used at a second property.Operation of the mine planning system was expensive, and it was evident that increased use required a costly upgrading of the UNIVAC in order to maintain an acceptable service level to all users. The system was re-evaluated,' and it was concluded that: core logging was not easily adaptable to a new property, nor flexible enough for exploration; plotting, grade interpolation, and digitizing required considerable manual effort; and that the UNIVAC operating system was difficult to learn.It was recommended that a study should determine if: core logging could be redesigned and/or implemented on a microcomputer; interactive graphics be used to reduce the effort for functions requiring visual interpretation; and the creation of input processors would assist users in setting up parameters for guiding the programs."

Jan 1, 1989

By C. R. Lattanzi, M. J. Davie, L. D. Smith, J. R. Goode

"The feasibility study determines the technical and economic viability of a project at the level of accuracy required by the owner to make an investment decision. The economic analysis usually includes calculation of the discounted cash flow. Key components of the cash flow include the project capital cost, the operating costs, construction schedule, production rate, product prices and financial details.This paper examines the feasibility study for a typical mining project. The paper discusses acceptable methods for the determination of the geological and mineable are reserves. The prerequisites for the development of suitable designs, and the calculation of capital and operating costs for the mine, processing plant, and infrastructure are reviewed. Important features of the cash flow analysis and its interpretation are presented.IntroductionThe commercial development of a mineral deposit invariably requires the investment of capital in preparing the deposit for production. It has always been necessary, therefore, to demonstrate to the investor of capital that production of a saleable commodity is both technically feasible and economically viable. The instrument typically used to make these determinations is the feasibility study .Traditionally, mining companies have been rather conservative in their approach to financial management. Until about thirty years ago, the capital required to develop a new mine was most frequently provided by internal corporate cash now and virtually all of the necessary technical and economic studies were performed 'in house'. Under these circumstances, there was little standardization as to what constituted an acceptable feasibility study, and even less as to what constituted an acceptable measure of economic viability."

Jan 1, 1991

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d'or"" analyse, dans une approche systémique, les travaux d'évaluation et de mise en valeur des gisements minéraux dans l'axe de la géologie, dans l'axée l'ingénierie et dans I ‘axe de l'économique. L’objectif est d'identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l'évaluation et de l'exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d'investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d'inventorie et de classification des réserves aux méthodes d'évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s'étendent qu’à l'axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l'information dans les axes de la géologie, de l'ingénierie et de l'économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d'évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s'inspire du Code australasien, peut facilement et rapidement s'intégrer dans les pratiques de l'industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l'échelle internationale. La proposition d'utiliser les marges d'erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu'une période de rodage."

Jan 1, 1992

By Philippe Portella

Current Ownership : AREVA NC-France & affiliates (63.4%), ONAREM-Niger (36.6%)Related Mines : Ariège, Artois, Arlette(initial Somaïrlease) and Tamou, Taza, Takriza, Tamgak(SMTT lease)Mining Method : Open Pits Reserves : about 14 000 tU Average grade : 0.3 % UEnvironmental Management : Certified ISO 14001 since November 2002Key figures :2003 output : 1126 tU number of employees at year end : 565 Current Ownership : AREVA NC-France & affiliates (34%), ONAREM-Niger (31%), OURD-Japan (25%), ENUSA-Spain (10%) Related Mines : the Akouta mine provides access to several adjacent orebodies(Akola, Akouta, and coming Afasto with Ebba North / South)Mining Method : Underground ?mainly room & pillars Reserves : about 29 000 tU Average grade : 0.40 to 0.50 % U3O8Environmental Management : Certified ISO 14001 since January 2003Key figures :2003 output : 2017 tU number of employees at year end: 1070

May 1, 2006

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By Francis Breton, Lei Pan, Kun Liu

"Effects of Fe, Cu and Mg minor alloying elements on creep properties of 8xxx aluminum conductor alloys were investigated by conducting compressive creep tests at 100 ºC under a constant load of 69 MPa. The microstructural evolution was studied using an optical microscope and electron backscatter diffraction technique. The creep properties were characterized by the primary creep strain in the first stage and the minimum creep rate in the second stage of creep deformation. Results showed that additions of all three minor alloying elements (Fe, Cu and Mg) demonstrated a beneficial effect on the creep resistance but individual alloying elements exhibited different impacts on creep properties. The additions of Fe and Mg showed a strong impact on both the primary creep strain and minimum creep rate, while the Cu addition displayed a favorable effect on the primary creep strain but no impact on the minimum creep rate. Microstructure observation revealed that with increasing Fe contents, the volume fraction of fine intermetallic dispersoids gradually increased while the subgrain size and misorientation angle became smaller, providing strong barriers to the dislocation and grain boundary movements. The addition of Cu moderately reduced the subgrain size and misorientation angle and in combination of solid solution strengthening it promoted the retardation of the creep deformation during the primary stage.INTRODUCTIONThe 8xxx aluminum conductor alloys offer significant advantages such as low density, high conductivity to weight ratio and low price over copper conductors and become an attractive candidate in electrical engineering and building wiring (McQueen, Chia, & Starke, 1986; Birol, 2009; Engler, Laptyeva, & Wang, 2013). The mass resistivity of aluminum conductors is one-half of copper conductors. Thus, only one-half the weight of aluminum is required for equivalent capacities. Therefore, this unique property coupled with a relatively low price of aluminum offers significant economic advantage to develop aluminum conductor alloys for electrical applications in the electrical wire industry."

Jan 1, 2016

By Rory S. McLaren

"Cost per ton as it relates to mobile underground vehicle maintenance and repair is invariably astronomical. The reason: the mechanic replaced a ten micron filter with a 250 micron filter because it appeared to be physically identical; the purchasing agent bought ""Brand X&apos;s"" filter because it was 25% cheaper- the result, a filter life 30% less; the hydraulic pump was sent for repair at a cost of $2000.00 and failed shortly after installation; pumps are failing because there is no testing equipment available in the workshop.This paper will identify a number of the common pitfalls resulting in high costs, and offer solutions to bring these costs to within acceptable limits.The following key issues will be discussed:A. Genuine parts replacement versus ""Brand X""B. Evaluating outside repair shopsC. The influence of environmental conditions on optional equipmentD. Personnel trainingE. Servicing and testing equipmentIntroductionThere is an old English aphorism, ""Look after the pennies, the pounds will look after themselves"".This paper is aimed at the pennies.Genuine Parts Replacement versus ""Brand X""High interest rates and floundering mineral prices are forcing many equipment owners and operators to purchase ""Brand X"" or ""Pirate"" parts in order to survive. ""Pirate"" part manufacturers invariably offer lucrative discounts which are most appealing to the average purchasing agent whose responsibility it is to save money. Unfortunately, in most cases, there is a tradeoff involved; when the price drops so does the quality, which can adversely affect owning and operating costs. Unless totally obvious, ""original"" or ""pirate"" part metamorphosis requires scrupulous analysis by competent individuals.Hydrostatic transmissions have been used successfully for many year s in various industries. They found their way into mobile underground loaders in the early seventies and have since become very unpopular in mining circles due to their apparent ""inherent unreliability"" and near ""prohibitive"" repair costs. The big benefit of the hydrostatic transmission is compact component packaging which enables the machine to work in very small headings."

Jan 1, 1983

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By John E. Udd, Peter Leinberger, Roman Kozarycz

"This paper is based on work done by the authors in a study of the structural features at a quarry excavated in Chazy limestone on the Island of Montreal. Observations on failures on the quarry walls and benches were recorded, and back analyses of small-scale failures were carried out, thus enabling an assessment to be made of the in-situ strength properties of the rock. Using this information, and data from shear tests in the laboratory, the authors made an analysis of the stability of the south wall of the quarry.IntroductionQuarrying, and excavating for foundations, in the Montreal area involves the removal of million s of tonnes of rock on an annual basis. Even when compared with the quantities mined at major open-pit mining operations, the production figures are impressive. At present, for example, crushed stone is produced at almost 20 quarrying operations either on, or near, the Island of Montreal. The annual capacities of the larger quarries are in excess of one million tonnes each. Lesser, but still substantial, production is achieved at the smaller quarries.Excavations, for foundations , especially during periods of peak construction activity, must also involve large quantities of rock . The writers, however , are not able to produce an estimate of the actual annual tonnages originating from excavations."

Jan 1, 1981

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder&apos;s history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016