Search Documents

By Gary Walters, Matthew White, Thomas W. Gonzales

The copper smelting industry has transitioned into the 21st century compliant with environmental regulations, new smelter installations and brown field expansions. The industry faces new challenges as copper in concentrate grades have decreased while contained impurities have increased. A new benchmarking survey was undertaken to update the last survey of 2016 for operating copper smelters in the world. The information collected was separated based on primary smelting technology rather than by geographical location and supplemented from published literature. Each smelting technology’s unique use of specialized process equipment, concentrate smelting capacity, and impurity flexibility are discussed INTRODUCTION The 20th century was a remarkable time for the growth of copper smelting. Electric, blast and reverberator furnaces dominated the smelting technology well past WWII. In the 1970s, SO2 regulations and high energy cost drove the development of new primary smelting technology. Technological advancements decreased energy consumption and enriched sulfur dioxide concentrations of the process off-gas to levels where sulfur capture in sulfuric acid plants was economically viable. The new smelting technologies began to replace reverberatory and electric furnaces starting in the late 1940s. A new paradigm in copper smelting was established and the enabler was then Outkumpu’s® flash smelting technology from the 1940s through to today. Now, Outotec had become the dominant primary smelting technology with over 44 copper flash smelting furnace installations world-wide. Figure 1 shows the historical installation statistics of primary smelting technologies over the last 70 years (ICSG 2018). The dominance and acceptance of the Outotec® smelting technology from the 1940s to current can be seen. Isasmelt® technology for copper was introduced in the 1970s and did not see advancement in new installations until the 1990s through today. Isasmelt® has 12 world-wide copper furnace installations to date. Mitsubishi® also introduced continuous smelting and converting technology in the 1970s, but had no new installations until the 1990s with a total of 5 copper smelters. Outotec Ausmelt® smelting technology had 3 installations in the 1990s and totals 10 furnaces. Most recently the Chinese technology of Bottom Blown and Submerged Lance Smelting began commercial operations in 2005 for total installations of 11, mostly in China. Other technologies, such as, El Teniente, Noranda, Inco, and Vanyukov furnaces have contributed to the overall global smelting capacity, but have not penetrated the smelting industry to challenge the existing dominant smelting technologies. The technology distribution in Figure 1 also shows flash smelting technology for sulfide concentrate domination untill 2000, bottom blow technology has become the preference in China. Currently, China is the only country building new smelting capacity. Isasmelt® technology also seen a large increase in installations in the current decade.

Jan 1, 2019

By M. J. A. Ruszala

Aggregates production is a huge global industry which uses an enormous amount of energy and produces a massive amount of unsalable fines. Reducing the amount of energy used per tonne of product and/or the amount of fines produced, would make a quarry more efficient. This reduction would make the quarry more environmentally friendly and profitable. This research looks at modelling Mountsorrel Quarry, a granite quarry in the United Kingdom (UK), using JKSimMet and Split-Desktop software packages in conjunction with the European Union (EU) project, EE-Quarry. Samples submitted to drop weight tests confirmed Mountsorrel Quarry granite as an extremely hard granite. Rock fracture data (t10) and energy of comminution (ECS) data were obtained from analysing the results. Split-Desktop image analysis software was utilized to determine the particle size distribution (PSD) of the primary crusher feed, as it contains particles too large to screen manually. It was also found that <1% of the feed is fines, which at Mountsorrel Quarry are classed as particles smaller than 5 mm, and that no particles were larger than 3,810 mm. JKSimMet was used to create a flowsheet of Mountsorrel Quarry. The crusher product PSDs were simulated and found to have strong correlations with experimental data, calculated by screening samples from conveyor belts, especially in the fines region, with a mean difference of 1%. The simulated primary crusher product PSD showed that it contains ~6% fines. A simulation over the entire quarry showed the product to be within the size range produced at Mountsorrel Quarry, and with a simulated fines content of 13%. When the CSS on the primary crusher was altered from 165.1 mm (the operating size on site) to 100.0 mm, it increased the overall percentage of fines produced by 3%, increased the power draw by 140.6 kW, but reduced the overall plant production percentage of fines by 2%. Two blasts were analysed on adjacent rock faces. They had identical blast designs, but the order of deck detonation varied; the first blast detonated the bottom deck before the top and vice versa in the second blast. For each blast, measurements of the feed PSD to the primary crusher, the number of particles that required secondary breakage on the quarry floor, acoustic levels and vibration readings were measured. No significant difference was identified between the two blasts in any of the parameters measured. In conclusion, a working model of Mountsorrel Quarry has been made in JKSimMet that has been validated against data from site and Split-Desktop has been used to simulate the primary crusher feed PSD, something that was previously unknown. The effect of reversing the order of deck detonation in a two deck blast was also analysed but with no significant difference between the two blasts found.

Aug 1, 2013

By George Efremidis, Markos Avlonitis, Elias C. Aifantis, Avraam Konstantinidis

"Nowadays, there is an increasing interest for realistic spring-block models capable of addressing precursor phenomena in catastrophic earthquake-induced landslides. By pre-defining the constitutive law between externally applied stress and induced local strain increments, the dynamic behaviour of the rock/soil slope can be studied by means of the distribution of slip events at the interface between the soil and the bedrock. It is shown that by relaxing the assumption of constant of externally applied stress rate and local strain increments, a robust 2D spring-block model can be formulated for studying triggered landslides. A cellular automaton is built in order to examine the dynamic behaviour and the stability of rock/soil slopes during the initiation of a landslide. The type and nature of the failure plane, as well as the triggering mechanism is studied. The different dynamic evolution modes of the slope can be mapped to specific shape parameters of the corresponding distributions of the incremental displacements. The proposed spring-block model can be used in order to understand, predict and minimize the impact of catastrophic landslides triggered by earthquakes.INTRODUCTIONEarthquakes have long been introduced as one of the major cause of landslides. Earthquake induced landslides are of great importance because they can cause considerable damage and life casualties. Existing analyses can provide landslide concentration, i.e. the number of landslide sources per square kilometer of surface area, as well as the distance from the earthquake source, which is related to the strength of shaking, the slope steepness, which is connected to shear stress, and finally the rock type, which is referred to material strength (Keefer, 1984). In spite of their great importance in social and economic life, earthquake-induced landslides are still considered as an open geotechnical problem. The dependence of the number and distribution of landslides on earthquake magnitude and ground shaking intensities is a crucial factor for the description and determination of the phenomenon. The hazardous types of earthquake-induced landslides, the most susceptible geologic materials and the reactivation of landslides originally triggered by nonseismic activity are some important topics for areas affected by landslides. Most of these areas present an irregular and asymmetric shape with respect to epicenters and fault ruptures, and also show a strong correlation with magnitude (Keefer, 1984, 2000). The number of landslides caused by an earthquake generally increases with increasing earthquake magnitude. Keefer (1984) presented a magnitude scale in order to quantify the number of earthquake-induced landslides. Malamud et al. (2004) have proposed an independent landslide-event magnitude scale on the earthquakes, based on the logarithm of the total landslides number associated with an event. The aforementioned studies try to relate the landslide magnitude scale to the visible effects of the triggering mechanisms."

Jan 1, 2015

By John Lamb

"The French Mine (formerly the Oregon) is 4 miles by road south of the Nickel Plate Mine. It lies on the steep eastern slope of the Similkameen River valley at elevation 4,000 feet, between Cahill and Winters Creeks.The property was discovered in .1901 and bought 4 years later by Messrs. French and Deardorf. It was developed in a modest way by the owners and by several companies until 1947, without success. The spectacular showings of bornite and chalcopyrite in the outcrop drew attention to its possibilities for copper rather than gold. Diamond drilling by the owners in 1947 yielded several high-grade gold intersections and created new interest. In 1949 the property was purchased by Kelowna Mines Hedley Limited. Exploration drilling and geological mapping outlined sufficient ore to commence production in 1950. Except for a few months each winter the operation has been continuous, and to the end of 1954 had produced almost 30,000 tons of high grade ore. The ore is crushed at the mine and hauled 8 miles by truck to the Company mill at Hedley, where it is treated together with the ore from Nickel Plate.Regional GeologyThe country rock consists of brown tuff, flows, limestone, and cherty formations belonging to the Nicola group (Rice 1947) of Triassic age. West of and just below the mine is a large mass of granodiorite which is part of the same body that underlies Nickel Plate Mountain. Bedding attitudes in the mine area are locally complicated, but dips are generally less than 45 degrees. To the south and below the mine the beds stand almost vertical, continuing downward with this attitude for 2,000 feet to Winters Creek. The main granodiorite contact is also steep, conforming to the sedimentary formations, whereas northward towards Nickel Plate it dips gently to the northwest, slightly flattter than the thick westerly dipping pile of sediments above it. The interpretation of this structure by Billingsley (1936) is that the French mine lies near the crest of the large northeasterly trending asymmetrical anticline which contains in its gently dipping western limb the Nickel Plate orebodies. The granodiorite body conforming roughly to this shape seems to occupy the core of the anticline. Sill-like prongs of granodiorite extend upward to the east from the main mass, outcropping over wide areas at the head of Winters Creek (Figure 1). There is a possibility that overthrusting from the west, similar to that on Nickel Plate Mountain, occurs not far below the French mine.An interesting feature of the granodiorite-sediment contact is that where it dips gently westward no alteration exists in the sediments, but where it has a steep front pronounced heat effects are indicated by the presence of a thousand-foot-wide zone of reddish garnet skarn."

Jan 1, 1949

By T. I. . I. Sibbald, D. E. Jiricka

The Goldfields area on the north shore of Lake Athabasca , was active in the thirties and early fortie . In 1934, Tom Box discovered gold mineralization in quartz veins in pyritized 'granite' at the ite of what wa to become the Box Mine of the Consolidated Mining and Smelting Company of Canada Ltd . In the rush of activity that followed numerou other gold occurrences were found. the most significant of the e being the Athona and Frontier prospects which underwent underground development bur did not reach production. Probable reserve identified to date in the Box and Athona deposits amount to some 3.5 million ton grading an average 0.ITT oz gold/ton . Some 10 to 15 million tons of lower grade, po ible reserve are also reported at the Box. From 1939 to 1942, the mine produced, from underground , 64,066 ounces of gold from ore grading 0.0452 oz gold/ton at a cost of between $1.5 and $2.0 a ton. The Goldfield area is underlain by upracrustal rock intruded by mafic bodies and invaded by ·granite'. The upracru tal . thought to be of Lower Proterozoic age are characterized by a helf-type ucce ion metamorpho ed under lowermiddle amphibolire facie conditions into quartzites, quartz-mica chi ts. dolomitic marbles, diop idic calc-silicates and cordierite-anthophyllite-biotite schi t . Amphibolites of presumed igneou origin form concordant to subconcordant units up to a few ten of metre thick in the upracrustals and occur as le regular masses in the 'g ranite·. Compositionally they vary from gabbroic to granodioritic. with the more mafic varieties being most common. Granitic rocks exhibiting a variety of textural , structural and compositional characteristics underlie most of the area. Four main units are recognized: foliated (older) 'granite', 'leucogranite', feldspar augen 'granite· and pyritic mine 'granite', however, in geological mapping the e are somewhat arbitrarily differentiated due to transitional relationships and admixture of types. Although there is no unambiguous age data available for the e 'granite ' adjacent northshore 'granite' of geologically similar age yield Rb-Sr isochron dates around 2000 Ma. The area is characterized by two major deformation events of which the earliest gave rise to the dominant regional foliation and to rare minor and outcrop scale folds. This foliation which in general parallels compositional layering is folded into the major Goldfields syncline, whose axis plunges weakly to moderately outh. Related open minor folds have subvertical axial surfaces which are locally paralleled by a weakly defined schistosity. Most rock display a pronounced rodding fabric, coaxial with second fold axes and apparently the product of this deformation event. However, a note of caution is introduced into this interpretation, as the rodding fabric is also parallel to first fold axe .

Jan 1, 1986

By G. Vibert Douglas

THE prospecter and geologist in the field, in the search for gold, are very often faced with a real difficulty. The: mineralized rock _frequently contains gold which is so finely divided or associated with sulphides that it is not recognizable in the gold pan. In recent years, the practice has been to take samples, send them to an assay office, and sit down and wait for results. This paper describes a method of solving the difficulty of proving the presence of this fine gold. The investigation is still in an experimental stage; but certain results have been obtained which would seem to justify publication. We do not consider that the method outlined is quantitative, but we believe that qualitative results are assured. The procedure has the great merit of simplicity. A sample of approximately two pounds of the mineralized rock should be taken and powdered as fine as is practicable. This powder is theo panned and the heavy minerals concentrated. Approximately two grams of these concentrates are taken for the test (one gram can be roughly gauged in the field by heaping up the powder on a Canadian twenty-five cent piece). The material is placed in a test-tube and 6 c.c. of a 10 per cent solution of iodine in alcohol are added (one-third of a test-tube full is approximately equal to 6 c.c.). Heat gently for about ten minutes over a spirit lamp, but without actual boiling. Allow to stand undisturbed until the sediment has settled to the bottom. Remove the clear iodine solution with an eye dropper. Allow it to fall, drop after drop, on a warmed pyrex watch-glass (the drops should be of equal size), taking care that the successive drops fall in the same place and that each drop evaporates before the next drop falls. Heat is applied to the lower side of the watch-glass by means of a spirit lamp. If gold is present in amounts of $2.00 or more per ton, a gold mirror will be formed on the watch-glass. This process of dropping and evaporating should be continued until no clear solution remains. If no mirror has appeared when all the solution has been used, another 6 c.c. of the iodine solution should be added to the powder and the process repeated. The absence of a mirror after the double treatment denotes an amount of gold less than two dollars per ton at the present price, or that the ore contains no gold. The mirror obtained must be washed with nitric acid ( 1: 1) to remove any copper, silver, lead, zinc, and iron. The yellow mirror remaining is pure gold.

Jan 1, 1937

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By R. E. Whitehead

"The earliest gold-mining operations in Ontario included the Cordova, Deloro, and Sophia mines north of Lake Ontario (see for example, Miller and Knight, 1914). The Cordova deposit, worked intermittently between 1891 and 1940, is reported to have yielded 22 774 oz of gold from 127 670 tons of ore averaging 0.19 oz/ton Au (Gordon et al., 1979). The property remained inactive for many years. In 1988, Gunnar Gold Inc. and Mill City Gold Inc. conducted a drilling program along the main Cordova vein. The present study is based on core from three drill holes through the Cordova gabbro (Fig. 1) and the carbonate alteration zones enveloping the quartz-carbonate veins. The relatively narrow width of the alteration zone and the availability of continuous sections of core provided an opportunity to conduct a compact mineralogical-chemical study of carbonate alteration and its effect on the redistribution of rare earth elements (REEs). Although the Cordova deposit is not of great economic importance, this study has revealed a number of interesting features which are interpreted as resulting from processes that may be applicable to gold-bearing quartz vein deposits elsewhere.The Cordova gabbro is layered in places, varying from fine-to coarse-grained and in color from light gray (feldspathic) to dark gray-green (amphibolitic). However, layering within the section of the gabbro considered here and which hosts the Cordova gold deposit is mainly textural rather than compositional. Samples of unaltered gabbro selected for analyses were medium- to coarse-grained; amphibolitic and anorthositic phases were avoided as being less representative of the general chemical composition of the gabbro.The Cordova intrusion has undergone regional metamorphism and consists dominantly of actinolite and saussuritized plagioclase with smaller amounts of granular clinozoisite and flaky chlorite; minor quartz, ilmenite, titanite, apatite, and calcite are typically present. Some actinolite grains have irregular rims of pleochroic green hornblende that is optically continuous with the actinolite. Both chlorite and clinozoisite occur in two modes. Chlorite occurs as an alteration product of actinolite and as separate grains in the groundmass. Clinozoisite and albite occur together as regional metamorphic alteration products of original plagioclase crystals and as discrete grains in the matrix.The main gold-bearing quartz-carbonate occurrence occupies an easterly trending, steeply southward-dipping carbonatized shear zone up to 15 m wide and 700 m long. The gold occurs principally in irregular lenses and veins of quartz-carbonate up to a foot thick occupying the lower part of the schistose shear zone within the gabbro. This zone consists of chlorite, biotite, and carbonate and is flanked on both sides by chlorite-carbonate schist lacking biotite. The chlorite-carbonate schist in turn grades into regionally metamorphosed actinolite-bearing undeformed gabbro.The dominant sulfide within the quartz-carbonate lenses and in the surrounding schist is pyrite which occurs mainly as small cubes (1 mm to 2 mm) generally making up less than 10% of the rock. Rare blebs of chalcopyrite are present. Magnetite is common throughout the schist."

Jan 1, 2001

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019

By X. J. Guo, H. X. Li

The biological heap leaching at Zijin copper mine is currently the largest industrial application of biohydrometallurgy and one of the earliest mines to develop biological metallurgy technology in China. Since 2001, through demonstration plant and different expansion stages, it has been developed to produce 20,000 tons cathode copper annually. However the ore grade of heap leaching gradually decline year by year with copper grade average at around 0.23% now. The copper mineral is mainly the secondary copper sulfide, and symbiosis with higher content pyrite, the sulfur and iron contents is about 15 times as copper in the ore (S/Cu>15), so the acid and iron treatment of leachate, extractant and acid mine waste water is a great challenge. Combined with located in the rainy area of southern China, huge amounts of over 10 million cubic meters acid drainage need to be treated every year, so the recovery of copper from waste water as well as low grade ore is one of the characteristics of this process. This paper in general introduced the operation of heap leaching, solvent extraction, stripping and electrowinning process in Zijin mine, summarized the experience of production and technical practice, and discussed the methods of heap construction, leaching rate enhancement, third phase formation and treatment, mine effluent treatment, resource recovery and heap slope reclamation. INTRODUCTION The Zijinshan gold and copper mine is located in southeast China, Fujian province, and the typical distribution characteristics of gold and copper deposit are "upper gold and lower copper", both are large porphyry deposits. By the end of 2017, the accumulated proven reserves of available gold resources were 318 tons, copper are 2.15 million tons, and the prospective reserves of copper are more than 5 million tons. The gold mining is open pit while the copper mining is open pit and underground. The cut-off grade of gold mining is 0.15 g/t, and that of copper mining is 0.15%. A large number of very low-grade gold ores (grade <0.30 g/t) adopt a combined ore-dressing process of “partial crushing/ore washing/reprocessing/heap leaching (overlying)/ carbon slurry" independently developed, while flotation and bio-heap leaching are adopted for copper mine. Among them, copper ore with more than 0.25% copper content enters the flotation system to produce copper concentrate, while that of less than 0.25% copper content is processed by bio-heap leaching, solvent extraction and electrowinning. Zijin biological heap leaching plant is the first mine in China to achieve the scale of annual output of ten thousand tons of cathode copper since 2006. In 2008, the solvent extraction and electrowinning system were expanded, now with a daily processing capacity of 20,000 tons of ores, an annual output of 20,000 tons of cathode copper, the expanded plant is the largest biohydrometallurgy plant in China.

Jan 1, 2019

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system&apos;s inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By Denni Nikols

"Planning for coal beneficiation in the electric utility industry is relatively complex, involving the coordination of experts and specialists in a broad range of fields, as well as compliance with a wide variety of government regulations.This paper examines the role of the planner, reviews possible benefits of coal beneficiation, identifies potential problems and illustrates a typical planning schedule.The steps involved in the planning process are:Step I-Bench- and pilot- washability studyStep 2- Wash plant designStep 3- Power plant and boiler designStep 4-Mine designStep 5-Major environmental and technical problems to address.IntroductionElectrical utilities and coal have a long and intimate relationship . Cleaned coal is becoming an increasingly popular fuel with the utilities for a variety of reasons. Generally, the greatest impetus to burn a cleaned or prepared coal fuel comes from the need to control airborne pollutants.Long-range planning is a standard practice for electric utilities, forecasts of demand must be made well into the future. Since the lead time required to provide new facilities is often as long as 10 years and the cost very high , planning becomes an important task.For a utility that owns and directs the operation of its coal mines, the mine planning or fuel acquisition planning takes on the magnitude of other corporate planning functions. It is from this perspective that a utility would view coal preparation. Except for the interaction of a coal-fi red plant on the actual mine design the planning considerations o f a beneficiating facility for a captive mine or a contract raw coal supply are about the same. Because TransAlta Utilities is currently supplied from captive mines, this discussion will tend to focus in that direction.It is the role of a planner to plan. This is easy to say but it is not always easy to do. Often we are working within a context that resembles the geological time scale. Frequently the objectives are not clearly defined when we begin and ultimately our plans are tested in the waters of government regulations and cost benefit analyses .Planning for beneficiation of Plains coal, or any coal, provides just such a test. The planner&apos;s role in this endeavour requires a wide vision. While parts of the process may be amenable to classical methods of project scheduling, the broad range of subjects and interaction of seemingly unrelated tasks is sure to obscure some of the considerations that must be made. Therefore, the planner&apos;s chief role is coordinating the work of many experts and specialists toward the final objective.Among the specialists are combustion , geo technical, mining, civil , and mineral processing engineers , geologists, hydrogeologists, soil, and reclamation experts to list a few.When one considers coal beneficiation, the planning part o f that consideration is probably more complex than any other single engineering function. Due to the company&apos;s location in the Alberta Plains and the proximity o f the mine to the thermal generating station, this paper will tend to emphasize that situation.Beneficiation may offer some advantages over run-of-mine coal to the power plant opeator. Some of these advantages are: removal of a contaminant, power plant efficiency gains , lower plant capital costs (for new plants), possible lower mining costs."

Jan 1, 1984

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By Eamonn F. Maher

Superconductivity is one of the most remarkable scientific phenomena ever investigated. It is the phenomenon whereby some materials exhibit zero resistance to the passage of an electric current when cooled to low temperatures, and requires a quantum mechanical explanation. Four Nobel prizes in physics have been awarded specifically on the subject of superconductivity, with many more enabled by superconducting technology. For example, particle beams are generated in accelerators and manipulated in ?particle beam lines? in the ?Big Physics? projects around the world eg. at CERN, Geneva, leading to major discoveries in fundamental particle physics. Similarly, at the JET Propulsion laboratory near Oxford, U.K, controlled nuclear fusion has been demonstrated, and magnetic containment of plasmas is key. In the chemical and biological sciences high field NMR spectroscopy has become indispensable for examining organic matter, revealing the mysteries of the workings of cells, genetics, and in the development of new polymers and pharmaceuticals. With all these very advanced uses for superconducting magnets, it is easy to forget that superconductivity is big business, not just a scientific curiosity. MRI (Magnetic Resonance Imaging) superconducting magnets, the key component of high resolution body scanners, use approximately half of the world?s superconducting wire ? the other half being mostly used in accelerator magnets. The MRI market is about 3 billion dollars per annum, and one MRI magnet uses 200km of wire. New applications for superconducting magnets are now appearing including ?Catheter steering?, enabling much shorter timescales for life-saving brain tumour removals and ?Functional MRI?, a whole new area in patient diagnostics. Whilst the use of low temperature superconductors (LTS) is now well established commercially in superconducting magnets and niche electronic applications, the application of LTS in electric power distribution and transport has been very limited to date. It is now more than fifteen years since the so-called High Temperature Superconductor (HTS) materials were discovered: these can be operated at liquid nitrogen temperatures rather than liquid helium temperatures. However, materials processing and scale-up issues have prevented their widespread use, and in particular the required price/performance criteria are only beginning to be reached except in certain niche markets. BSCCO (Bismuth Strontium Calcium Copper Oxide) tapes up to one km long are now readily available, and have been demonstrated in high current cables for power distribution networks, but the general consensus is that 1) it is difficult to reduce the price much further because of the silver matrix required and 2) in applications where coils are required eg. motors, generators, transformers etc the properties of BSCCO are rather poor because of the critical current dependence on magnetic field. Magnetic fields are always associated with coils and windings, and such fields are of course fundamental to the operation of all electrical machines. YBCO (Yttrium Barium Copper Oxide) however, has good characteristics in field and for the last few years there has been intensive research and development costing several tens of millions of dollars worldwide into the scale-up of production of so-called ?coated conductor?. This ?second generation? tape can be produced by any of many different film deposition techniques, with more or less success for short lengths, but as yet it is unavailable in lengths more than a few tens of metres.

Oct 1, 2003

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994

By M. J. Michaud, M. J. Lavigne

"Abstract - North American Palladium Ltd. operates its Lac des Iles open pit palladium mine 85 km north of the city of Thunder Bay, Ontario. The Roby Zone deposit occurs within the mafic/ultramafic Lac des Iles Intrusive Complex (LDI-IC), which was created by multiple pulses of magma of varying composition within several closely spaced chambers. Chaotic lithological distribution, the presence of magmatic breccias, and the rarity of rhythmic layering suggest a dynamic intrusive environment with disruptive magma pulses. As of December 31, 2001, measured and indicated resources for the 950 m long by 815 m wide Roby Zone deposit totalled 159 Mt grading 1.55 g/t Pd, 0.17 g/t Pt, 0.12 g/t Au, 0.05% Cu, and 0.05% Ni at a palladium cut-off grade of 0.7 g/t. The Roby Zone contains an additional 73 Mt of inferred resources at similar grades.The Roby Zone is dominated by varitextured gabbro containing pipes and pods of breccia, and large blocks (~60 m across) of varying lithology. Mineralization at Lac des Iles occurs as: (1) a PGEand base metal-rich magmatic matrix of breccia (breccia ore); (2) mineralized dikes or sills (gabbronorite in North Roby ore); (3) lower-grade mineralization in varitextured units that are host to the distinctive breccia ore and envelope the North Roby ore; and (4) high-grade mineralization associated with strong silicate alteration exemplified by high-grade ore.The close spatial association of the mineralized breccias with both varitextured units and silicate alteration leads to an interpretation that the energetic magma that created breccia was charged with a dissolved fluid, and that this deuteric fluid exsolved at high temperatures to migrate through crystal mush, enhancing crystallization along its pathways, resulting in variable grain size. This transformation occurred at high temperature and produced sulfide-poor, varitextured gabbro-hosted mineralization exemplified by some of the mineralization in the North Roby Zone, and also found throughout the Roby Zone. The association of hydrous silicate alteration with mineralization can be explained by continuing fluid migration during cooling and continued metal transport. Résumé - North American Palladium Ltd. opère la mine à ciel ouvert de Lac des Iles située à 85 km au nord de Thunder Bay, Ontario. Le gisement Roby Zone est encaissé dans le complexe mafique/ultramafique de Lac des Iles (LDI-IC), lequel représente une intrusion polyphasée créée par plusieurs pulses magmatiques de différente composition à l’intérieur de chambres magmatiques fermés. La distribution chaotique des lithologies, la présence de brèches magmatiques, et la quasi-absence de litage rythmique suggèrent un environnement magmatique dynamique perturbé par l’introduction de nouveau magma. Au 31 décembre 2001, les ressources mesurées et indiquées s’élevaient à 159 millions de tonnes titrant 1,55 g/t Pd, 0,17 g/t Pt, 0,12 g/t Au, 0,05% Cu, et 0,05% Ni, pour une teneur de coupure de 0,7 g/t Pd. De plus, la Roby Zone contient 73 millions de tonnes de ressources inférées à une teneur similaire.La Roby Zone est principalement encaissée dans un gabbro de texture hétérogène (varitextured) caractérisé par des cheminées et des lentilles de brèches et des énormes blocs (environ 60 m de diamètre) de plusieurs lithologies. Au Lac des Iles, la minéralisation en EGP et en métaux de base se retrouve dans la matrice magmatique de brèches (breccia ore), dans des dykes ou des sills minéralisés (gabbronorite dans la zone North Roby ore), comme minerai de basse teneur encaissant le minerai de brèche (breccia ore) et enveloppant la zone North Roby. Du minerai de haute teneur est également associé avec une forte altération en silicates dans la zone high-grade ore.L’étroite association spatiale entre les brèches minéralisées et les unités de texture variée (varitextured) et l’altération en silicate suggère que le magma énergique qui a causé la bréchification était chargé de fluides. Ces fluides deutérique"

Jan 1, 2001

By W. P. Clement, M. C. Bell

"PT International Nickel Indonesia, a subsidiary of Inco Limited, mines and processes nickel laterite ores for the supply of nickel matte, primarily to the Japanese market. It has large ore reserves and a substantial portion of its energy requirement is supplied from its own hydro-electric plant. Since the early 1980s, the company has increased its production level and has dramatically reduced its unit costs. Projects are in progress to further decrease costs and recently a major expansion - 31% increase in nominal capacity - has been undertaken, consistent with marketing opportunity in Japan. The expansion project, which has a low capital cost per unit of production, is outlined in this paper.IntroductionPT Inco is a fully integrated mining and smelting facility located in Indonesia on the island of Sulawesi, and is based on a very large, world class nickel laterite orebody located 60 km inland from the Gulf of Bone. Construction of a single furnace line plant started in 1973. Complete supporting infrastructure of townsite, hospital, schools, shopping centres, road systems, and an airport, all had to be built. Prior to completing the first phase, the decision to expand the plant to a three kiln-furnace line was made. A major factor in the decision was the ability to develop the hydroelectric potential of the nearby Larona River. This involved construction of a 30 m high dam, and a 7 km surface canal to the generating station. The penstocks drop 150m to three 55 Mw turbines. The power generated is sufficient to supply the entire electrical load for the complete smelting complex and town site. The unique capability to supply the high smelting energy requirements for a lateritic nickel ore by fully captive hydro power, has, over the past decade insulated PT Inco from the large upward swings in oil prices suffered by other lateritic nickel producers.Wet ore is first partially dried to 20% moisture in two co-currently fired rotary driers, screened on an internal trommel, and delivered to two dry ore storage buildings. The partially dried ore is calcined at 750°C and partially reduced in three large 100 m by 5.5 m kilns. Reduction is accomplished by lancing bunker C oil onto the ore bed at the discharge end of the kiln. The kilns are equipped with five air pipes with onboard blowers to gradually bum the combustible gases generated by the lance oil. The kilns were also originally equipped with two side burners to supply additional heat close to the feed end of the kiln. Calcined ore is transferred by 20 ton refractory lined containers to the furnace feed bins at the top of the smelter. Smelting is carried out in three 18 m diameter furnaces powered by 45 Mw transformers. Slag is skimmed at 1550°C through water cooled breast plates and removed to the slag dump by Haulmaster Carriers. Matte of 25% Ni, 1O% S, 65% Fe is tapped at 1350°C into the converter aisle. The iron is slagged in converters to produce a nickel sulphide matte at 80% Ni. Three rotary Kaldo converters were initially installed. The product matte is granulated, dried, and shipped in returnable rubber bags to Japan. Most of the matte is fluid-bed roasted to nickel oxide and then directly reduced in a second reducing fluid bed reactor at our facilities in Japan.The smelting complex was designed to smelt two million tonnes of dry ore per year, equivalent to 34 000 tonne nickel production at an ore grade of 2% Ni. The cost of the entire project including working capital was $900 million."

Jan 1, 1990