Search Documents

By Guillermo Diaz, Roberto Pérez, René del Villar

"Pulp-froth interface position is a key variable in column operation. In plant practice, it is commonly estimated through a system of three pressure-transducers which allows the calculation of the pulp height. An alternate method based on the measurement of the conductivity profile across the interface has been proposed and successfully tested. Both methods however, present some practical problems related to the assumptions made in the calculation of the pulp height in the former case, and to the response time and the precision of the reading in the latter case.In this paper, the use of the neural network technique for improving the estimation of the pulp-froth interface in flotation columns is discussed. The technique is used with both conductivity-based and three pressure-transducer methods. Results obtained in a 2"" laboratory column and a 12"" pilot scale column are presented. A major obstacle in applying this approach in practise is the training of the artificial neural network. This problem is analyzed here for the conductivity-based method and some solutions are proposed."

Jan 1, 1995

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968

By B. Loveday, G. W. Delaney, S. Cummins

"Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage.The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed."

Jan 1, 2012

By Lorna Ortiz-Soto

A series of titiania- and silica-supported Au, Pt and Pt-Au catalysts prepared through different synthetic routes have been investigated in terms of their structural properties, adsorption of CO, and catalytic activity for the selective catalytic reduction of NO by propylene and the oxidation of and CO. Catalysts prepared by incipient wetness impregnation from individual Pt and Au precursors, exhibited characteristics very similar to those of monometallic Pt catalysts. This behavior is consistent with a model in which the two metals remain segregated due to their miscibility gap, and only Pt participates in the adsorption of CO and the reactions under consideration. In contrast, catalysts prepared from a Pt2Au4(C=CtBu)8 organo-bimetallic cluster precursor exhibited different behavior both in terms of CO adsorption and their catalytic activity for the three reactions examined. The combination of the kinetic, spectroscopic and structural characterization data suggests that in this case Pt and Au remain intimately mixed in the form of Pt-Au bimetallic particles, and that the presence of Au modifies the behavior of Pt.

Oct 1, 2003

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By A. E. Gillis

"Some or all of the following benefits can be expected following application of automatic control to a grinding circuit:1. Maintenance of Optimum Mill Load Level2. Improved Uniformity of Grind3. Increased Productivity4. Decreased Power Costs per Unit of Product5, Reduced Ball Wear per Unit of Product6. Reduced Labour Costs per Unit of Product7. Reduced Operator SupervisionTo establish an indication of the benefits that could be expected through automation of the grinding circuit at East Malartic Mines Ltd. it was agreed that the Department of Mines and Milltronics Limited should jointly conduct a survey of the existing grinding circuit and operation.Aside from establishing feasibility, an important purpose of this survey was to determine costs of a suggested control system that East Malartic Mines Ltd. management might be in a position to assess the economics of the proposal and justification of the investment.The survey involved the taking of sound recordings of rod and ball mills during manual operations, locating circuit bottlenecks, establishing time constants and determining the number and location of sensors for good automatic control."

Jan 1, 1966

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By R. V. Kumar, F. Tailoka

In order to use ZnO laden dust as a possible desulphurization reagent, it is important to evaluate thermodynamics of the Zn-O-S system. At temperatures greater than 1450 K, there is an uncertainty in the thermodynamic data for the reaction of zinc with sulfur to form Zinc sulfide. In this work, the standard free energy has been determined using an electrochemical cell: Pt, Mo, MoO2/YSZ/ZnO, ZnS, S02, Pt., between 1198 and 1602 K. AG° varies from -145,880 to -88,100 J (± 2500) , with a phase change to ZnS (g) by sublimation occurring between 1450 and 1460 K. This is supported by thermogravimetric analysis which shows about 80% weight loss in ZnS from 1273 to 1473 K. Feasibility reactions were also performed and confirmed that ZnS (g) is formed when ZnO reacts with FeS (1473 to 1653 K) or with Fe-Csat-S(1473-1673 K). There is therefore potential for the utilization of ZnO laden waste as an additional or alternative reagent for desulfurisation.

Jan 1, 2004

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By D. T. A. Symons, M. M. Kapnistos

"Gravity profiles were established over five known Middle Silurian pinnacle reef s in Lambton County, southwestern Ontario. The profiles were approximately 3 km long, with stations every 60 m. Four fairly recent technological developments were used which now make the gravity method relatively efficient and inexpensive compared to the techniques available two decades ago. These are: (1) a La Coste-Romberg model G gravimeter to measure the gravitational attraction with a sensitivity of 0.01 mgal; (2) a Sokkisha model B-2 semiautomatic engineers level to measure the station elevations with an accuracy of 0.5 cm; (3) a Huntec FS-3 hammer reflection seismograph to determine the overburden thickness to an accuracy of ± 7%; and (4) a modern microcomputer to process the data sets and mathematically filter the gravity values. Thus, two men can measure and analyze approximately 1 km of profile per day and obtain the residual gravity profile to an accuracy of ± 0. 05 mgal. Positive gravity anomalies of 0.17 to 0.72 mgal were observed along all five profiles that approximately delineate the dimensions of the known pinnacle reefs, which have an average height of 120 m, diameter of 1500 m and depth to top of 575 m. The relative ease of the gravity survey method makes it a cost-effective technique for hydrocarbon exploration in southwestern Ontario. IntroductionPinnacle reefs are important sources of oil and gas. Although the pinnacle reefs in southwestern Ontario are small, they may contain commercial pools of oil and gas because of their proximity to refineries. They are also useful for subsurface storage of gas to meet the winter surge in gas demand.At present, geophysical exploration for new pinnacle reefs is done primarily by relatively expensive seismic methods, which are also limited in southwestern Ontario by prohibitions on blasting. Gravity methods of exploration were attempted more than two decades ago in this region. (Pohly, 1954); however, the level of technology at that time made the method marginal in sensitivity and quite expensive. Several subsequent developments- gravimeters with greater sensitivity and operating ease, ""self-levelling"" levels for elevation control, hammer seismic reflection units for determining overburden thickness and portable microcomputers for efficient data analysis-have significantly improved the precision and cost effectiveness of the gravity method. Five known pinnacle reefs were selected in Lambton County, southwestern Ontario (Fig. 1), to test the effectiveness of integrating these developments to locate and define additional reefs. Isolated reefs were chosen to avoid the problem of the gravity effect s of one reef interfering with those of a neighbouring reef. The surveys were facilitated by choosing reefs with a concession road passing directly over them ."

Jan 1, 1980

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By T. Sugawara, H. Sekimoto

Electrorefining of low-grade copper alloys containing various amounts of nickel, lead, antimony, bismuth, arsenic, selenium, silver, and gold in sulfamic acid media was demonstrated. The copper concentration of the alloys used as an anode was 70–90 wt%. The electrolyte contained 100 g L-1 of free sulfamic acid and 40 g L-1 of cupric ion. Galvanostatic electrolysis was conducted at 200–300 A m-2 in the electrolyte using a low-grade copper alloy anode and a stainless steel cathode at 25C. The terminal voltage was approximately 0.8 V at the start of the electrolysis, although it increased periodically to approximately 2.0 V and then shortly returned to its initial value. Nickel, lead, and arsenic from the anode dissolved in the electrolyte and were removed. Antimony, bismuth, selenium, and silver were removed as solids. Consequently, a dense copper cathode was obtained, and the concentration of copper was evaluated by inductively coupled plasma – optical emission spectrometry to be 99.82–99.99 wt%. INTRODUCTION Electrorefining of copper is conventionally carried out in a sulfuric acid electrolyte using crude copper assaying at 99.5 wt% Cu as the anode (Biswas & Davenport, 1994). Elements more noble than copper do not react anodically, and consequently, they are distributed in anode slimes. Elements less noble than copper dissolve from the anode. Nickel and arsenic are stabilized as aqueous species. Lead, antimony, and bismuth react with water, sulfuric acid, or arsenic acid to form barely soluble compounds; thus, they are distributed in anode slimes. An emerging issue in the electrolytic refining of copper is an increase of impurities in crude copper used as the anode (Moats et al., 2013). This is due to an increase in the content of impurities in copper concentrates as well as an increase in the types of secondary copper feedstocks (e.g., E-Scraps, automotive shredder residues, and smelting residues) treated in the copper pyrometallurgical process. An extreme case is a copper smelter that does not use copper concentrates as feedstocks. In such a process, copper-bearing feedstocks are smelted in a top submerged lance furnace to prepare low-grade copper alloys assaying at 80– 90 wt% Cu (Sekimoto et al., 2013). Such low-grade copper is not acceptable as an anode in the conventional copper electrolytic refining process because it is easily passivated during electrolysis. Consequently, electrolytic copper is produced by leaching the atomized low-grade copper in a sulfuric acid solution with oxygen, followed by electrowinning. However, electrowinning should be avoided whenever possible because the electrical energy consumed in electrowinning is 5–10 times higher than that consumed in electrorefining. Therefore, the development of technologies for electrorefining of low-grade copper alloys is desirabl.

Jan 1, 2019

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By R. S. James, D. C. Peck, P. T. Chubb

"The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered mafic intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendriticpegmatitic mafic pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and magmatic breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to 100/0 within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that affected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd:Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Several factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic interaction with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion.The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Complex, U.S.A.) in terms of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economic concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginaltype POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By Dogan Paktunc, Larry J. Hulbert, Robert C. Carne, D. Conrad Grégoire

Abstract -A thin layer of stratiform Ni-Zn-PGE sulfide mineralization of sedimentary-diagenetic origin was deposited during the Middle to Upper Devonian in the euxinic "Nick basin". The mineralized unit (2:3 cm thick), which seems to have been developed over the entire sedimentary basin of >80 km2, consists of pyrite, vaesite (NiSi), and sphalerite. The average grade of the mineralization is about 5.3% Ni, 0.73% Zn, ?770 ppb (PGE+Au), and up to 61 ppm Re. Anomalous Se, As, Mo, P, Ba and U are present. A minimum of 0.90 x 106 tonnes of Ni were deposited in the basin (based on a bed thickness of 3 cm) during the Devonian. The unique metal association, extensive lateral distribution, persistent metal grade, mineralogical makeup, and stratigraphic control demonstrate that this is a new deposit type and a new geological environment for Ni and PGE +Au. The sulfide layer occurs at the base of a Phosphatic Chert Member which is underlain by a distinctive marker unit consisting of concretionary limestone structures. The limestone spheroids may represent a vent-specific carbonate facies developed adjacent to faults that emanated nutrient­ rich hydrothermal discharges just prior to the main mineralizing event. The suite of elements associated with the Nick mineralization suggests that the ore-forming metals were originally bound to organic matter derived from decaying marine organisms. Discharge of hot brines bearing organic­ matter-bound metals took place along numerous conduits within basin faults that are now manifest as bitumen veins. Our syndiagenetic model proposes that these fluids were discharged laterally from the conduits into the unconsolidated bottom sediment (ooze). The introduction of this metalliferous fluid, rich in organic matter, stimulated biological activity and bacterial reduction of its contained S04 to sulfide. Hot, dense, laterally migrating hydrothermal fluid precipitated thin sulfide-rich 1arninae within bottom sediment. Published thermodynamic studies suggest that the diagnostic vaesite­ pyrite assemblage crystallized at approximately 138°C. The ?34:S values range from -14.7 o/oo to-10.0 o/oo and are up to 34 o/00 lighter than locally surrounding sulfides and age-equivalent mineralized strata elsewhere in the Selwyn Basin. The ?13:C values of calcite in the footwall of the mineralized unit ( -12 o/00 to -6 o/00) are isotopically much lighter than regional values. The lighter isotopic character is attributed to the hydrothermal discharge of fluids enriched in organic compounds. Although geochemical profiles of the lower Earn Group sediments that host the Nick mineralization reveal that these black shales are not distinctive, the unusual Ni, Zn, PGE, U, Ba, and P elemental associations and their anomalous concentrations in stream sediments can be used to explore for this deposit type.

Jan 1, 1992