Search Documents

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By C. Jay Hodgson

Hydrothermal systems form on land where and when an impermeable cap-rock unit ( either natural or self-sealed) , a permeable aquifer. and permeable discharge and recharge channels (cross-stratal permeability) develop in an anomalously hot part of the crust. A consideration of the relationship between magmatic and tectonic events in volcanically active areas indicates these conditions arise during: (1) the resurgent doming stage of the resurgent caldera cycle; (2) following movement on the bounding faults of tilted fault blocks ; and (3) as a result of hydrothermal boring associated with the intrusion of major sills. On the assumption that the submarine hydrothermal systems which deposit volcanogenic massive sulphide ores are comparable to subaerial hydrothermal systems, it is suggested that: (1) the horizon of mineralization corresponds to the time period when conditions favour the development of hydrothermal systems, as outlined above; (2) exploration for Cu-rich Cu-Zn-Pb or Cu-Zn ores should be directed to paletopographically high areas near discharge conduits , whereas exploration for Cu-poor ZnPb ores should concentrate on paleotopographically low areas down slope from conduits; (3) deposits with stringer zones lying above normally permeable units may be underlain by regionally extensive weakly mineralized and altered zones (self-seal caps) ; (4.) in the absence of a self -sealed cap, the ore horizon may be underlain by a naturally impermeable unit (e .g. a fine clastic sediment) ; (5) the condition of cross-stratal permeability may be evidenced by features such as dykes. alignment of vari ous magmatic and hydrothermal phenomena, abrupt thickness changes in stratiform units indicative of ponding against syn-volcanic faults, and fault-scarp slump deposits; (6) the condition of high heat flow may be evidenced by near-surface magmatism and steep thermal gradients preserved in metamorphic mineral assemblages.

Jan 1, 1977

By Marco Lombard, Paulus Kapolo, Christopher J. Greet

"The conversion of a concentrator from one grinding media type to another is a major undertaking in terms of both financial and technical risk. So, a strategy of completing sufficient laboratory and field tests to mitigate this risk, and give the operation confidence that advancing to plant trial will give a high probability for success.The objectives of this paper are twofold: to provide the reader with a strategy for mitigating risk prior to undertaking a plant trial; and to provide a statistical basis for analysing plant trial data. That is, when employing an electrochemically inert grinding media in the primary grinding circuit it is possible to change the pulp chemistry of the system and improve the metallurgical response of the ore.This paper tracks the changes in pulp chemistry and metallurgical performance of Rosh Pinah Zinc Corporation’s silver/lead/zinc concentrator as the primary ball mill was converted from forged steel grinding media to high chrome grinding media. The changed in metallurgical performance are correlated to the shift in pulp chemistry.INTRODUCTIONTheoryBruckard et al (2011) recently published an article describe the effect of the grinding environment on the flotation of copper sulphides. While this paper confined its discussion to copper sulphides the arguments presented apply equally to other sulphide mineral systems. Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:Cathode (sulphide mineral): ½O2 + H2O + 2e- ? 2OH- (1)Anode (grinding media): Fe ? Fe2+ + 2e- (2)A galvanic couple between the grinding media and the sulphide mineral(s) exists, which increases the corrosion rate of the forged steel media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).The application of more electrochemically inert grinding media to “real” ore systems at an industrial level to improve metallurgical performance has not gained universal acceptance. The aim of this paper is to provide a protocol for conducting laboratory and plant test work that clearly demonstrate that metallurgical benefits are not only possible, but measureable, by way of example. In this case, the work conducted at Rosh Pinah Zinc Corporation in Namibia is described."

Jan 1, 2013

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By Arthur B. Yates

"The nickel deposits of Sudbury, discovered in .1885, have probably commanded as much attention as any single group of orebodies in the world. They have been the major source of the world's nickel supply since 1903, when their production first surpassed that from the Pacific Island of New Caledonia. From 1903 to 1914 the production from New Caledonia remained essentially constant, whereas that from Sudbury increased from 13,000,000 to 50,000,000 pounds a year. After 1914 the production from New Caledonia gradually dropped to about 4,000,000 pounds in 1919, where it remained until 1923. During these years the Canadian production increased steadily and since 1923 has gone up at an amazing rate to a peak of over 280,000,000 pounds in 1941. Meanwhile the New Caledonia production increased to about 10,000,000 pounds until the pressure of war raised it to roughly 14,000,000 pounds a year.The Sudbury deposits, because they have been the source of 80 per cent of the world supply of nickel, because of their economic importance to the world of metals, and because they are geologically unique in their occurrence, structure, and genesis, have attracted foremost consideration and the literature relative to their geology is voluminous. This is particularly true in regard to genesis.There is a significant and interesting parallel in time between the advancement of the science of economic geology and the great expansion of the nickel industry. The controversies regarding the fundamental classification of orebodies into generalized types were in full swing during the height of the development and expansion of the great nickel mines, and the Sudbury deposits, being the most important and the only ones of the sulphide type extensively developed, have been the chief source of information in regard to this type. The observations and the conclusions drawn thereon from numerous studies of the various mines of the district have not only influenced, but are the essence of, this chapter of the science."

Jan 1, 1954

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminicki, D. Evans-Lamswood

"Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite. La caractérisation systématique de la minéralogie des gîtes de sulfures massifs peut fournir des indications précieuses sur la genèse des minerais et le traitement métallurgique qui ne seraient pas disponibles par d’autres méthodes. Nous décrivons un procédé par lequel (1) un algorithme est utilisé pour calculer l’abondance de minéraux normatifs à partir d’analyses lithogéochimiques, (2) les résultats sont exprimés dans des blocs diagrammes, (3) les résultats sont par la suite validés par analyse d’image automatisée sur un microscope électronique à balayage en électrons rétrodiffusés et par cartographie en rayons X sur des échantillons constitués de grains montés en résine, et (4) les résultats de cette validation sont combinés aux données texturales obtenues par microscopie optique.Cette technique est appliquée aux sulfures magmatiques de Ni-Cu-Co du gisement Ovoïde, en utilisant les analyses géochimiques de 3175 échantillons de roche totale. L’Ovoïde comprend trois types de minerai. Le type I est situé au centre du gisement; il est riche en magnétite et pauvre en pyrrhotite avec des quantités intermédiaires de pentlandite et de chalcopyrite. Le minerai de type II entoure le minerai de type I et est riche en pentlandite et en chalcopyrite avec des quantités intermédiaires de pyrrhotite et de magnétite. Le minerai de type III se trouve à la base ainsi qu’à bordure externe de la partie nord du gisement; il est riche en pyrrhotite et pauvre en chalcopyrite, avec un contenu intermédiaire en pentlandite et une quantité faible à moyenne de magnétite."

Jan 1, 2012

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By R. Simonson

Agenda ? Need and Introduction ? Interface Management Programs ? Outcomes of Successful Interface Management ? Key Success Factors ? Lessons Learned ? Concluding Remarks Need for Interface Management ? Complex projects ? Larger in scale ? Physically dispersed and delivered remotely ? Involved with several stakeholders ? Risks thus imposed due to: ? Iterative and dynamic nature ? Large information flow ? Document revisions and information updates ? Related sources of Risk: ? Ineffective communication ? Poor work relationships ? Person to job mismatches ? Failure to clarify expectations

Aug 1, 2013

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By Brian A. Ferguson, Raynald O. Vezina, Marielle Gaudet, Raoul R. Boissonneault

"Kiena has been committed to developing a fresh management and employee relations approach since the commencement of production in 1981. The functional organizational structure encourages joint participation and commitment on the part of all employees to common goals in safety and production. The results over the last four years have been extraordinary. Kiena won the John T. Ryan Canada Trophy for 1983 for its safety record and has experienced a steadily increasing productivity through the application of new mining equipment and technology in the hands of a well-trained and motivated team of employees.This paper serves to highlight the fact that productivity, safetyand technical innovation are closely linked to employee participationand involvement which are likely to be the key to theCanadian mining industry's survival in the years ahead.This presentation follows up on an earlier unpublished paper, given at the 84th Annual Meeting of CIM in Quebec City in April, 1982, which discussed the philosophy and the planning which took place before implementation of the management and employee relations system at Kiena. This present paper reviews and expands on material given in the earlier work. IntroductionThe mining industry, which has always been considered as rather conservative in its approach, has experienced with some regularity, cyclical periods related to metal prices. These cycles, previously foreseeable to some extent have become less coherent over recent years during which time the industry has had to face fierce international competition. The issue to productivity is without doubt the major concern of the mining industry in Canada today and it represents the greatest challenge facing us during the present decade. Developments that have been made in mining technology over the precious two decades have failed to completely produce the significant advancements in higher over-all productivity that were expected."

Jan 1, 1987

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By Tiziana Apuani

The study refers to an area of about 70 km2, extended in the Italian Central Alps along the the San Giacomo Valley where different civil and mining works are present The regional geological setting is related to the Pennidic Nappe arrangement, characterized by the emplacement of sub-horizontal gneissic bodies resulting from the Mesoalpine isoclinalic folding of crystalline basements, emplaced throw East, and separated by matasedimentary cover units. The investigated geological rocks, belong to the ?Tambò?Unit, overlapped by its meta-sedimentary cover and by the ?Suretta? Unit. The tectonic contact gently dips to the E?NE. The valley, furrowed by the Liro Torrent, follows a N?S striking tectonic lineament, almost parallel to the nappe contact. A number of more then 70 sites, distributed in the studied area, were chosen and detailed structural and geomechanical field surveys were performed to characterize the rock masses, its intact rock and discontinuities. The procedure identifies the number of joint sets, their representative orientation, the set spacing, the type of movement, the amount of dilatation, the degree of alteration, the roughness coefficient, the presence and nature of infill. Rock mass quality indexes, such as the Rock Mass Rating (Bieniawski, 1989) or the Geological Strength Index (Hoek et al. 2002) have been evaluated in each surveyed site. The work is a contribute in assessing how the geometrical and geomechanical properties of the rock masses can be regarded as regionalized variables. The spatial distribution of these properties is a function of the geological and structural phenomena at which the rock masses have been subjected. The presented geostatistical analysis regards the spatial variation of the orientation of the most representative joint set.

May 1, 2009

By Jarek Jakubec

The new euphoria in diamond exploration brings with it a need to understand the challenges that new projects can face in different stages of the development and risks that the commercial outcomes from the new projects fall short of expectations. In many cases, the problems are related to a poor understanding of the technical risks and a failure to adequately address them during the course of investigation. Failure to evaluate all disciplines to the same level of certainty could lead to a situation where the important issues are only identified late in the project development, resulting in costly delays and financial difficulties. The diamond projects located in Canadian Arctic, with its challenging environmental, geographical, social, political and geological contexts are especially sensitive to the high variability of the outcome. This presentation highlights some of the technical aspects that could be the leading sources of risk in diamond projects and could ultimately result in inappropriate mine designs, reducing the economic outcome.

May 1, 2006

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007