Search Documents

By Lihong

A series of Fe2O3-elimination experiments were conducted on feldspar samples from Tangshan Stone?powder Plant. These experimental methods include scrubbing desliming, flotation,rod milling and high gradient magnetic separation. Some technical factors of feldspar concentration and a new technological flow?sheet of ceramics raw material concentration were put forward.

May 1, 2003

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By Lyall J. Lichty

THE property of New Calumet Mines, Limited, is on Calumet island, in the Ottawa river, about sixty-six miles northwest of Ottawa. Lead and zinc orebodies were discovered here in 1893. A gravity concentration plant was built in 1912 but was not a success metallurgically, and the plant was later destroyed by fire. A programme of diamond drilling on the property, started in 1937 and continuing to 1942, indicated ore reserves amounting to 1,300,000 tons averaging 2.75 per cent lead, 8.82 per cent zinc, and 0.041 oz. gold and 6.24 oz. silver per ton( l ). These orebodies have been developed underground by cross-cutting and drifting from a three-compartment vertical shaft, sunk to a depth of 745 feet. 'The ore is a contact metamorphic deposit occurring in rocks of the Grenville series, on or near the contact between biotite gneiss and an overlying calcareous amphibolite(2,3). It consists chiefly of iron-bearing sphalerite, galena, pyrrhotite, pyrite, and minor amounts of chalcopyriteand argentite. The gangue minerals closely associated with the ore are calcite, quartz, and various lime-silicate minerals.

Jan 1, 1945

By K. Karan

Oxygen reduction reaction in PEM fuel cell cathodes involves participation of three reactants - oxygen, hydrogen ions, and electrons. Electrochemical reaction in the catalyst layer is, therefore, influenced by how these species are transported to the reaction site. The two-phase boundary locations at which percolating networks of ionically conducting electrolyte and electronically conducting Pt/C meet are feasible reaction sites. The electrolyte phase also provides pathway for the transport of dissolved oxygen. Most of the 3-D models describe the catalyst layer as an ultra-thin layer, thereby, losing useful information on the distribution of electrochemical reaction rate. In this paper, we extend our previous work on 2-D cross-the-channel modeling of PEMFC cathode based on agglomerate catalyst layer. In particular, we take a closer look at the influence of proton conductivity on the reaction rate distribution in the catalyst layer. As well, we re-examine the role of anisotropic transport coefficient of the porous transport layer (PTL), commonly known as the gas diffusion layer, on the current density distribution under the channel and the rib of the flow-field plates. Results from both a 2¬D and a 3-D models will be presented.

Jan 1, 2005

By E. M. Córdoba

The effect of the Fe3+ lFe2+ redox couple on the chemical and biological dissolution of chalcopyrite was studied. All the tests were carried out in stirred flasks with 100 mL of a ferric/ferrous sulphate solution, in the absence or in the presence of bacteria (iron- or sulphur-oxidizing) and at low (35 DC) and high (68DC) temperature. The initial redox potential was controlled between 300 and 600 m V Ag/ AgCI and silver was used as chemical catalyst. The results showed that the oxidizing action of ferric ion on the chalcopyrite was controlled, in all cases, by nucleation and precipitation of jarosites on unreacted particles. The tendency of Fe3+lFe2+ solutions towards equilibrium favours the activities of both ions to be equal. Consequently, the dissolution rate was faster at relatively low redox potentials (between 400 and 500 mY) than at high values (600 mY). In this sense, the presence of ferrous ion in the system is a key factor to control hydrolysis and precipitation of ferric ion. Unlike jarosite, the elemental sulphur produced during dissolution of chalcopyrite was porous and did not act as a diffusion barrier.

Jan 1, 2007

By K. Murase

Potentiostatic electrodeposition behavior of dendritic copper from acidic copper(I) chloride (cuprous chloride) baths containing sodium chloride and sodium bromide was investigated. The morphology, or appearance, of copper dendrite and the sodium content in the dendrite as an impurity were both influenced by deposition potential (0 to ?150 mV vs. SHE) and bath temperature (R.T. to 60 C), while the current efficiency for the deposition was 99% or more irrespective of the deposition conditions examined. The bath pH did not affect the deposition behavior in the pH range of 0 to 2. Bath temperature was found to be the most important factor influencing the deposition current. The current density of the dendrite deposition on a titanium cathode was lower than that onto a copper cathode with the same substrate surface area. The reproducibility of the current for the dendrite deposition was poorer when an as-polished titanium cathode was used, although it was improved by surface treatment of the cathode with an HF-HNO3-H3PO4 solution before electrodeposition. The deposition behaviors were discussed with the potential-pH diagram of the Cu-Cl-H2O system.

Jan 1, 2007

By D. P. Fenton

The Phelps Dodge El Paso Rod Mill produces approximately 2.4 million pounds per day of copper rod from a casting and rolling operation. The newly formed rod is treated to remove mill scale and oxides using a sulfuric acid and hydrogen peroxide solution which is bled periodically when the copper concentration reaches 30-35 g/L. The bleed solution is heated to 75° C to destroy the residual peroxide. Copper is then recovered in a 270 cell EMEW electrowinning plant. Clean acid is also regenerated in the EMEW plant and is returned to the rod cleaning circuit. The EMEW plant commissioned in January 2006, has two operators and replaces a copper sulfate plant with fourteen operators. The EMEW plant has a capacity of 1700 kg/day of cathode copper at 2.1 kWh/kg copper deposited. The electrowinning plant operates in closed circuit with the rod mill returning up to 2600 kg/day of sulfuric acid resulting in zero discharge. Use of dimensionally stable anodes (DSA®) ensures that the acid quality is maintained in the closed loop operation. The operating conditions, performance and plant experience of the EMEW copper and acid recovery plant are discussed.

Jan 1, 2007

By J. A. Muñoz

In this work, short and long-term tests were performed using different massive mineral sulfide specimens (chalcopyrite, pyrite, sphalerite, galena, covellite and chalcocite) of museum grade and quartz of analytical grade in an acid medium containing silver ions. After attack, the samples were observed by SEM and products characterized by EDS. Parallel, massive specimens of pyrite (FeS2) and chalcopyrite (CuFeS2) were embedded in an epoxy resin, either electrically isolated or in electrical contact, and treated with silver ions in the presence of bacteria. Finally, massive chalcopyrite and pyrite electrodes were subjected to electrochemical measurements in an acid medium under different experimental conditions (addition of silver ions and inoculation). The results showed that silver deposition takes place preferentially on specific mineral surfaces: chalcopyrite, galena, covellite and chalcocite. The chemical reaction of silver ions with pyrite and sphalerite was negligible at low silver concentration (8 ppm). But sphalerite reacted with silver ions at higher silver concentration (100 ppm). In a mixture of chalcopyrite and pyrite, silver was deposited on the former surface creating new cathodic sites which sped up the electrochemical reactions of chalcopyrite dissolution.

Jan 1, 2007

By Mel Torrie

1 Want access to low level vehicle data so 3rd party apps can be applied as desired 2 Hardware Agnostic (COTS plug and play) 3 Common/Open protocols that facilitate integration and the coexistence of a variety of applications on a variety of equipment 4 Minimum computer hardware footprint 5 Technology Independence (including comm. backbone)

May 1, 2013

By H. R. Kempthorne

"The Property of Bevcon Mines Limited, including a recently acquired adjoining south group, occupies an area of 2,625 acres in northeast Louvicourt township, Abitibi county, Quebec. It is situated 17 miles east of Val d'Or at the junction of provincial highways 58 and 59.Gold was first discovered in the area in 1931 by the late S. B. Jowsey on the present property of Buffaddison Gold Mines adjoining to the west. However, it was not until the winter of 1944-45 that diamond drilling encountered encouraging results on the Bevcon claims. During the period 1946-1948 a shaft was sunk to 1,000 feet and considerable development undertaken from the 500-foot to the 1,000-foot levels. Between 1947 and 1950 approximately 24,000 tons of dump ore and 48,000 tons of ore by stoping were milled at Perron Gold Mines. The favourable results of these tests prompted the decision to construct a milling plant at Bevcon. The mill began operating in July 1952, and presently has a capacity of 800 tons per day. In 1953 the shaft was deepened to 1,600 feet and is currently (1955) being driven to 2,225 feet.Total production of gold to the end of 1954 has been 101,024 ounces from the milling of 697,427 tons of ore of an average grade of 0·163 ounces per ton.GeologyThe Bevcon orebodies occur in a granodiorite stock which has an east-west length of approximately 4 miles and a maximum width of 1 1/2 miles. The property covers the central portion of the stock and its contacts with the Keewatin volcanics. Approximately one-third of the northern contact and one-half of the southern contact are contained within the Bevcon claims. The granodiorite has been cut by acid (feldspar porphyry) and basic dykes trending east-west. A younger diabase dyke, 300 feet wide, strikes northeasterly across the property 1,000 feet east of the shaft.The main ore zone, striking east-west, lies between the more northerly porphyry dyke and the north granodiorite-greenstone contact. It has been extensively sheared, fractured, altered, and mineralized by gold-bearing solutions. It is approximately 2,000 feet Jong from the west boundary towards the diabase dyke. The shaft is centrally located and passes through the south contact of the ore zone at the 500-foot level. The zone increases in width and trends northerly with depth, due to the porphyry and greenstone contacts having average dips of 80 degrees and 70 degrees respectively to the north. Thus on the uppermost or 500-foot level the width is 150 to 200 feet, and at the present bottom level at 1,600 feet the width is 400 to 500 feet.Another gold-bearing zone has been indicated 200 to 400 feet south of the main ore zone by limited surface drilling."

Jan 1, 1949

By Paul MacLean

MAC TSM ?Mining and Biodiversity Conservation 1.Corporate biodiversity conservation policy, accountability and communications 2.Facility-Level biodiversity conservation planning and implementation 3.Biodiversity conservation reporting ?Activities indicative of level AA -AAA (formerly 4-5) performance: ?Independent verification ?Integration into broader business strategy and planning processes ?Engagement with communities of interest ?Commitment to actively partner with other organisations for biodiversity conservation

May 1, 2011

By C. Caballero, A. Warczok, K. Itagaki, A. Moyano, J. Font

The Codelco Norte Smelter process 2,500 tpd of arsenic-bearing concentrates with an arsenic content of up to 1.5% in one of its two main smelting units, the Teniente Converter. The product, 1,100 tpd high-grade matte or white metal, is traditionally fed to the PS converters, while the 1,700 tpd of slag is fed to the slag cleaning electric furnace for copper recovery. This is achieved in a very reductive environment which reduces the viscosity of the slag and enhances the sedimentation of the high-grade matte droplets. The behavior of arsenic in this non-oxidative environment was studied at lab-scale and fundamental thermodynamic data were obtained. Based on these data a thermodynamicbase model to assess the arsenic behavior in reductive environment was developed. It is based on a mass balance for the reduction and sedimentation stages performed in an electric furnace which allows the recovery of high-grade matte droplets after decreasing the viscosity of the slag. This model can be a very suitable tool for predicting fractional distribution of arsenic in the slag cleaning electric furnace, when the distribution ratio, vapor saturation degree, temperature, y As and pO2 are given.

Jan 1, 2007

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

By A. W. Jacobs

SHORTLY after Denny, Robson, and Irwin(l) published their first paper, in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery. It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in: (1) Shakers on machine columns, vibrated? by drills (2) Vials placed in drill holes to be blasted (3) Both homogeneous and heterogeneous. mixture with explosives ( 4) Packages with tamping (5) Compressed-air lines (6) Special compressed-air ejectors for use while drilling and after blasting (7) The discharge of ventilation fans (8) The filters of respirators It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium powder, and would interfere unduly with underground routine. Later, animal experiments by Denny, Robson, and Irwin(2) showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.

Jan 1, 1944

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

By J. K. Van Beek

The Deep Underground Science and Engineering Laboratory (DUSEL) is a scientific facility that will be placed in the deeper reaches of the Homestake mine, Lead, SD. Our team of geologists and engineers is carrying out the first scientific project awarded to the site ? Towards a Transparent Earth. Taking advantage of the thousands of open exploratory and sand-line holes, we are installing the beginnings of a seismic observatory. Each installed station consists of a 3-D accelerometer package and a 1 nanoradian 2-D tilt meter. In order to allow for a variety of monitoring and characterization studies, the array instruments are sensitive over the frequency bandwidth of 0.2 - 1 KHz. Three, three component accelerometer stations are currently installed ? in a 140 m deep bore beneath the slurry pump house, and in 12 m deep bores on the 2000-foot level, 800 and 400 m from the Ross shaft. There is a tilt-meter installed at each 2000 level station. These installations are in 150 mm diameter sand-holes. From the currently installed tilt sensors we are investigating solid earth deformation as a response to tidal potential. The accelerometers are being used to locate and characterize events associated with mine dewatering and rehabilitation.

May 1, 2009

By Anna Maria Venezia

Bimetallic Au-Pd catalysts supported on amorphous silica-alumina (ASA) with vary amount of alumina (0, 8, 14, 28 and 100%) were prepared by the simultaneous reduction of palladium and gold precursors by ethanol in the presence of the polyvinylpyrrolidone (PVP). X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated formation of alloyed Au-Pd particles. Ammonia temperature programmed desorption measurements were performed to monitor the acid strength and the amount of acid sites on the catalysts after their reduction with 10%H2/Ar at 573 K for 1h. The effect of the support acidity on the catalytic activity was investigated in the simultaneous hydrogenation (HYD) of toluene (T) and naphthalene (NP) in the presence of dibenzothiophene (DBT). Coke formation was also determined. Under the selected conditions (P = 5.0 MPa, T = 523 K, WHSV = 41.2 h-1), all the catalysts were resistant to poisoning with 113 ppm of S (as DBT). The hydrogenation activity of toluene and the HDS activity of DBT were found to correlate with the concentration of the medium strength acid sites. The enhancement of the HYD activity and the S- tolerance was related to modifications of the electronic properties of the metal atom upon interaction with the Brönsted acid sites and upon intermetallic interaction.

Oct 1, 2003

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By D. F. Sangster

"Eight volcanogenic massive sulphide districts in Canada and Japan, ranging in age from Archean to Miocene, were selected for analysis. The study revealed that: {I) each district has an average diameter of 32 km; (2) the districts contain 4 to 20 deposits each, with an average of /2 deposits; (3) the average total base metal content per district is 4.6 million tonnes, with a coefficient of variation of32%; (4) ranked in order of size, the largest deposit in each district contains, on average, 67% of the total metal and the second largest about 13 %. The remaining deposits range downward in decreasing proportions. Empirical observations such as these may be used f or evaluating the undiscovered potential of new districts as well as contributing to a better understanding of the distribution and genesis of this important class of base metal deposits. Previous WorkThe characteristic geological features o f volcanogenic massive sulphide deposits have been described by numerous authors over the past fifteen years and it is now widely accepted that these deposits comprise a major ""deposit-type."" In addition to these geological parameters, however, it is now becoming apparent that volcanogenic massive sulphide deposits show several distinctive grade-tonnage relationships. For example, Singer et al. (1975) demonstrated a slight negative correlation between copper grade and ore tonnage in their sampling of 146 volcanogenic deposits. In a study of 110 Canadian Precambrian deposits of this type, Boldy (1977) showed that the size of the modal deposit is 0.39 million tons, that of the median deposit is 1.40 million tons and the arithmetic average is 6.85 million tons. Moreover, Boldy's data show that the average grade of combined base metals (Cu + Zn + Pb) for each of the se three deposit-sizes is, respectively, 6.25%, 5.35% and 6.47%. Because the lead content of Canadian Precambrian volcanogeni c deposits is most frequently less than 1%, the total metal grade is effectively Cu + Zn . From Figure 2 in Bold y (1977), it can be seen that 83% of the deposits fall in the range of 0.l to 10 million tons ."

Jan 1, 1980

By G. M. Ritcey, S. H. Lucas

"On the north shore of the St. Lawrence River, in Quebec, are located orebodies of low-grade titaniferous magnetite. The Quebec Mining Exploration Company (SOQUEM), who have an interest in the deposits, believed that beneficiation of the could generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility. A joint research project of SOQUEM and CANMET investigated alkaline roasting of a magnetic concentrate, followed by leaching of the calcine and separation and recovery of Cr and V by solvent extraction. Aluminum was recovered by precipitation.The present paper describes the roast-leach bench-scale and pilot-plant work leading to the development of the optimum conditions f or the integrated process.A plant flowsheet was developed for the treatment of 5 x 106 tons of magnetic concentrate per annum. Estimates of capital and operating costs were made.Based on a recovery of approximately 90% V, 85% Cr and 75% AI, the total hydrometallurgical plant fixed capital costs, including mining, concentration and shipping, are estimated at $1.021 x 109; the operating costs are estimated at $131.92/ton concentrate. Annual revenue from the Na2CrO4.H2O, V2O5 and A12O3 produced is calculated to be $421 x 106.IntroductionThe Quebec Mining Exploration Company (SOQUEM) acquired in 1968 an interest in four titaniferous magnetite orebodies located in Eastern Quebec. 85 miles north of Mingan on the north shore of the St. Lawrence River. The Mingan deposit, with an estimated tonnage of one billion tons, has a reported average grade of 43% Fe, 6.3% Ti , 1.60% Cr, 0.19% V and 6.1% Al with minor amounts of nickel. SOQUEM, on the basis of previous bench-scale data, believed that the recovery of chromium, vanadium and alumina by alkaline roasting would generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility on the coast. One of the approaches selected by SOQUEM for beneficiation of the ore consisted of a combination of magnetic concentration followed by alkaline roasting of the calcine."

Jan 1, 1980