Search Documents

By J. Basi, J. A. Finch

ABSTRACT Testing the effects of bubble size (Db) in a Mo cleaning ?otation column at Highland Valley Copper mine indicated that increasing the proportion of small (< 1 mm) bubbles signi?cantly improved column metallurgical response, compared to typical operation. The results were a three- to four-fold Mo recovery increase and a 1 to 2% Mo (absolute) concentrate grade increase. The improvedcolumn operation produced a 4% Mo plant recovery increase. This study also showed that modelling the ?otation rate constant (k) as an inverse square function of Db was more accurate than considering k to be inversely proportional to Db.

Jan 1, 2010

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019

By Christian Brits, Bob Blain, Lloyd Buckingham, Juliu Stieger, Jean-Francoi Dupont

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By A. Valdivieso

Reducing accident rates keeps getting more and more complex as the usual tools enter a curve of diminishing results. Fortunately, nothing modifies behaviour in a stronger and wider way than having a robust safety culture. On the other hand, managing cultural change is difficult and the risk of back-fire is very high, especially if the workforce does not trust our intentions. A personalized approach of well chosen and targeted actions tends to be the only yet difficult option. We have found, via experience in the metallurgy and chemistry industries, a way of preparing the company and the workforce to accept these sorts of culture changing measures faster and easier. Using company-wide changes based on workplace perception, yields the most optimal acceptance. It is based in the principle that we all use clues in our environment as guides to choose our behaviour. So, controlling the perception that our workplace generates can affect behaviour and simplify our task before it even starts. It is a matter of using the tools that other disciplines such as marketing, social engineering and architecture bring to us and adapting them to a very defined objective: Having our installations “sell” safety so that our people unconsciously believe that they must adapt to safety values in order to “do well” in said environment. INTRODUCTION After decades of improvements in accident rates, we are understandably hitting a diminishing results curve: most actions that spectacularly reduced accidents in the past (e.g., Innovation in Personal Protection equipment, adapting international standards and legislation, and innovative safety programs; Figure 1) now hardly get us the exponential gains we saw years back, regardless of the investment we put on them. Furthermore, the improvements in safety of the last 3 decades have been creating new sets of issues that start to show their face such as: By reducing accidents we can create feelings of invulnerability as we lose view of the consequences. With innovative protection equipment we increase Risk Homeostasis, meaning that people behave in a more dangerous way in order to maintain a constant level of risk in their lives (Getting closer to fire after getting better fire-proof garments for example). Too much Legislation can create a feeling of disengagement from personal responsibility. And despite improvements, we haven’t really solved the production vs safety confrontation, it is now stigmatized and less visible, yet it tends to reappear in moments of weakness.

Jan 1, 2019

By Doris Stüben, Geoffrey P. Glasby, Akira Usui, Jörg-Detlef Eckhardt, Bruce W. Mountain, Zsolt Berner

"Abstract - Twenty-seven marine Mn and Fe deposits chosen for their diverse origins have been analyzed for five platinum-group elements (PGE). The PGE display their highest concentrations in hydrogenous Mn crusts and nodules, lesser concentrations in diagenetic nodules and two to three orders of magnitude lower concentrations in hydrothermal Mn and Fe crusts. This difference of behavior reflects the well-known fractionation of Mn and Fe from the other transition elements, rare earth elements (REE) and PGE in hydrothermal Mn and Fe crusts. Pt, Ru, Rh, and Ir show a close geochemical coherence in these deposits and are differentiated from Pd which shows a negative anomaly with respect to the other PGE in hydrogenous and diagenetic Mn deposits. Pd is less depleted than the other PGE and the Pd anomaly much less pronounced in the hydrothermal Mn and Fe crusts relative to the hydrogenous and diagenetic Mn deposits.Stability field diagrams show no evidence for the oxidation of Pt to the tetravalent state in seawater as suggested by some authors. Rather, Pt appears to be present in seawater as Pt(OH)2 0. Adsorption of Pt(OH)2 0 onto the surface of Mn and Fe oxyhydroxide minerals may explain the enrichment of Pt in marine Mn deposits. However, Pt metal is the thermodynamically stable solid phase of Pt under seawater conditions and reduction of Pt(OH)2 0 to Pt metal, particularly in the vicinity of the oxygen minimum zone, is possible, although the high Ce/La ratios of the Co-rich Mn crusts do not support this hypothesis. Pt, Ru, Rh, and Ir display their maximum concentrations in the Corich Mn crusts. This may reflect, among other things, the low growth rates of these deposits. The stability field diagram of Pd shows that Pd is undersaturated in seawater and occurs in seawater dominantly as PdCl4 2- and anionic mixed-hydroxide-chloride complexes. This would explain the anomalous position of Pd among the PGE with respect to its uptake into marine Mn deposits. A study of inter-element associations indicates that the incorporation of the PGE from meteoritic dust plays only a minor role in the uptake of these elements into marine Mn deposits. The PGE remain the most poorly studied group of elements in marine Mn deposits. The data presented here emphasize the need for the establishment of a more comprehensive database of the PGE in marine Mn deposits in order to understand more fully their uptake into marine Mn deposits and their pathways through the oceans."

Jan 1, 1999

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV."

Jan 1, 2017

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By Henk Dijkman, Wageningen University, Paula Gonzalez Contreras, Irene Sánchez-Andrea, Jan Weijma, Silvia Vega

"More than 20 years ago, Paques B.V. introduced innovative biotechnologies to recover metals and to remove sulfate from aqueous streams. These technologies find their origin in the exploration of microorganisms involved in the global sulfur cycle. Currently, several sulfur cycle biotechnologies are applied successfully at full-scale. The sulfur cycle is closely linked with the iron cycle, and also the latter offers opportunities for application of innovative biotechnology for the mining industry. Microorganisms of the natural iron cycle carry out reactions that are not feasible by chemical methods such as ferrous iron oxidation with oxygen at pH below 4. Iron oxidation with oxygen can be conducted using microorganisms living at pH between 0.5 and 7 and at temperatures between 0 and 95ºC. Remarkably these microorganisms can also carry out arsenite oxidation at similar acidic conditions and high temperatures. Making use of the extreme features of these microorganisms, Paques and Wageningen University have developed a biological process to precipitate arsenic as scorodite. This biological formation of scorodite is a novel combination of biological oxidation and biocrystallization. Depending on the level of saturation, biological oxidation rates and operational conditions, we could control the formation of the iron precipitates such as jarosite and scorodite. Currently new microorganisms have been harvested from hot springs and rock acid mine drainage to foster the growth of specialized microbial communities with potential high iron and arsenic oxidation capacities and higher resistance to other metals. In our paper we address the ongoing research and development of the bioscorodite process.THE USE OF IRON TO REMOVE ARSENIC In 2015 several environmental disasters related to the release of mine wastewater and tailings occurred. On August 5th, a waste water spill occurred from the Gold King Mine near Silverton, Colorado. A dam holding the tailing pond was damaged and spilled three million US gallons (11 ML) of mine wastewater and tailings, including elements such as cadmium, lead and arsenic, into Cement Creek, a tributary of the Animas River in Colorado. “At their peak, arsenic levels were 300 times the normal level and lead was 3,500 times the normal level” (The Guardian, 2015). In early November, another collapse of a mining dam in the Brazilian state of Minas Gerais spilled between ten and sixteen thousand US gallons of water and sediment after a dam failed from an iron ore mine. Arsenic and mercury polluted the Doce River, arsenic levels were found more than ten times above the legal limit in some places of the river (The Guardian, 2015). Waste production is inevitable during Mining. However, a preventive waste management strategy could have minimised waste production, maximised waste reuse and classified waste by their hazardous degree."

Jan 1, 2016

By André Chagnon, Michel Malo, Benoît Dubé, Chantal Pelchat

"Abstract- In the southern Gaspé Appalachians, gold mineralization is spatially associated with the Acadian dextral strike-slip Grand Pabos-Restigouche fault system. Two different structurally-controlled gold prospects, the Lac Arsenault and the Saint-André-de-Ristigouche, are described to unravel the genesis of gold mineralization in this part of the Canadian Appalachians.At the Lac Arsenault gold prospect, gold mineralization consists of Au-As-Pb-Zn-Cu-(Ag) polymetallic fault-filled quartz veins with laminated textures emplaced in brittle-ductile sinistral X shear fractures. Mineralized veins are hosted by Middle Ordovician graywacke of the Arsenault Formation, belonging to the Dunnage Zone, the Early Paleozoic oceanic domain of the Appalachians. Terrigeneous rocks of the Arsenault are regionally metamorphosed at the lower greenshist facies and the mineralized veins are included in a zone of Fe-carbonate alteration.The Sb-Au-As mineralization of the Saint-André-de-Ristigouche gold prospect, in the southwestern Gaspé area, comprises extension veins in the extension direction emplaced in brittle conditions. Mineralized veins are hosted by calcilutite and laminated silty and argillaceous limestone of the Early Silurian part of the White Head Formation, which belongs to the Gaspé Belt, the Middle Paleozoic successor basin in the Gaspé Appalachians. Metamorphic grade of the White Head Formation in the southwestern Gaspé area is very low, but the gold mineralization is included in a zone of hydrothermal propylitic alteration which includes two Cu-skarn mineral occurrences. The Lac Arsenault gold prospect has many characteristics of "greenstone-hosted quartz-carbonate vein" deposits whereas the southwestern Gaspé area, which includes the Saint-André-de- Ristigouche gold prospect, shows affinities with the geological setting of sediment-hosted gold deposits (Carlin-like deposits). The two gold prospects are controlled by the Grand Pabos- Restigouche fault system but they were not emplaced at the same level in the crust. Acadian strikeslip fauting played a major role in their respective genesis in providing channelways for ore-bearing fluids. The recognition of the analogy of the geological setting of the southwestern Gaspé area with that of Carlin-like mineralization gives new ideas for exploration in the area and elsewhere in the Appalachians.Résumé - Dans le sud des Appalaches de la Gaspésie, on trouve des minéralisations aurifères spatialement associées au système de failles de coulissage dextre acadien de Grand Pabos-Restigouche. Deux indices très différents, Lac Arsenault et Saint-André-de-Ristigouche, sont décrits pour évaluer la genèse des minéralisations aurifères à contrôle structural de cette partie des Appalaches canadiennes. Au Lac Arsenault, la minéralisation aurifère comprend des veines polymétalliques à Au-As-Pb- Zn-Cu-(Ag) en remplissage de failles. Ces veines à texture laminaire se retrouvent dans des zones de cisaillement fragiles-ductiles senestres de type X. Les veines minéralisées sont encaissées dans les grauwackes d’âge Ordovicien moyen de la Formation d’Arsenault appartenant à la zone de Dunnage, le domaine océanique du Paléozoïque précoce des Appalaches canadiennes. Les roches terrigènes de l’Arsenault sont métamorphisées régionalement au faciès inférieur des schistes verts et les veines aurifères sont dans de larges zones d’altération dolomitique (Fe-carbonate).Dans le sud-ouest de la Gaspésie, la minéralisation à Sb-Au-As de Saint-André-de-Ristigouche est dans des veines d’extension comprises dans la direction d’extension et mises en place dans des conditions de déformation fragile. Les veines minéralisées sont encaissées dans les calcaires argileux et les calcilutites de la partie silurienne de la Formation de White Head qui appartient à la ceinture de Gaspé, le bassin successeur du Paléozoïque moyen des Appalaches de la Gaspésie. Le degré métamorphique des roches du White Head est très bas, mais"

Jan 1, 1998

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990

By J. F. Henderson, N. H. . C. Fraser

"Camlaren Mines, Limited, owns a group of claims near Gordon lake, in the Northwest Territories about 45 miles northeast of Yellowknife. The Hump vein on the property was explored continuously from the summer of 1937 to December, 1938, when all work was stopped. The two-compartment vertical shaft sunk near the vein is 380 feet deep and drifts and cross-cuts on the 200- and 350-foot levels total 2,241 feet . This exploration indicated 13,177 tons of ore with a gold content of between ½ and 1 ounce a ton1GEOLOGY AND STRUCTUREThe property is underlain by remarkably fresh greywacke and slate of the Early Precambrian Yellowknife group. The thickness of the b ~ds averages 1 to 2 feet, although that of the coarser greywacke may be 10 feet or more. Most of the greywacke beds show a gradation in grain from sandy at the base to slaty at the top. They are composed of chlorite, sericite; carbonate, and detrital quartz and feldspar grains.The structure of the greywacke and slate underlying a part of the property of Camlaren Mines, Limited, is shown in Fig. 1. The beds are isoclinally folded so that they dip at steep to vertical angles and at many places are overturned. The axes of the folds are 50 to several hundred feet apart, and generally plunge at angles of 45° or steeper. The beds along the axes of the folds generally meet to form a sharp V, and at the point of the V, or axial part of the fold, the beds are commonly ruptured . Minor faulting movements along the broken crests of the folds in many cases result in well-defined shear zones. Discontinuous quartz veins and irregular lens-like masses of quartz lying more or less parallel with the bedding are plentiful throughout the sediments, but tend to be concentrated along the ruptured and sheared, anticlinal and synclinal fold axes ( Fig. 1)."

Jan 1, 1954

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984