Search Documents

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By A. Sacit Saydam

"Induced polarization/resistivity and magnetometer surveys have been carried out over the Casmo molybdenite deposit in mountainous terrain of northern British Columbia. Molybdenite occurs in quartz-bearing fractures with or without pyrite along a zone of hydrothermal alteration and intense fracturing, believed to be a northerly dipping fault zone, within medium-grained equigranular and porphyritic quartz monzonite.The molybdenite-bearing zone is characterized by a significant resistivity low, a metal factor high and a subtle IP low flanked by highs outside the mineralized area. Magnetic trends, indicated by a magnetometer survey, generally parallel the zone and strike direction of the different intrusive phases, and have been helpful in delineating contacts and faults in the area.IntroductionThe Casmo molybdenite deposit is 6 km southwest of the asbestos mining town of Cassiar in northern British Columbia, at an elevation of 1,550 metres. Molybdenite was first discovered during the early 1950s and the first important exploration work was done in 1964. Between 1964 and 1971, about 25,000 feet of drilling was done by various operators, as a result of which 33.7 million tons of molybdenite ore was drill indicated at a grade of 0.123%. In 1979, Shell Canada Resources entered into an option agreement with the former operator, New Jersey Zinc Corporation. Shell completed 27,000 feet of diamond drilling between 1979 and 1980 and ha s reported 75 million tonnes of drill-indicated ore with an average grade of 0.13% MoS2• This paper is a case history of IP I resistivity and magnetometer surveys done over the Casmo deposit during 1979 and 1980."

Jan 1, 1983

By S. Yano, S. Takagi, Y. Nagaya, T. Akai, T. Ishida, Z. Bennour, T. Suzuki

"It is often reported that the concept of single-plane-fracture is not sufficient to account for the productivity from shale gas/oil wells. Many researchers introduce the concept of the stimulated reservoir volume to describe observed production behaviour. However, the characteristics of the stimulated reservoir volume are not well understood. In this study, to investigate the characteristics of fractures and surrounding region induced by the hydraulic fracturing, a devised hydraulic fracturing experiment was conducted using the cylindrical shale specimens in the laboratory.Two resins were prepared as the fracturing fluid for the experiments: cyanoacrylate, an instant glue, mixed with a fluorescent paint (resin A), and methyl metaacrylate, a thermosetting acrylic resin, mixed with a fluorescent paint (resin B). These resins were able to fix within the specimen after fracturing. This is because the present study aimed to only detect fractures induced by hydraulic fracturing. Cut sections of the specimens were observed under ultraviolet light irradiation. It is expected that the hydraulically induced fractures and the surrounding regions will be detected because the induced fractures filled with the resin should emit light, while the other parts will not.The specimens, which were collected from the Kushiro Coal Mine in Hokkaido, Japan at the depth around 275 m, were roughly 85 mm in diameter, 170 mm in length, and cored normal to the sedimentary planes. An injection hole with a 10-mm diameter was drilled onto the center of the specimen parallel to the sedimentary plane to simulate hydraulic fracturing in shale gas development. The experiment was conducted under a uniaxial loading condition of 3 MPa and the fracturing fluid was injected into the sealed injection hole at a constant flow rate using a syringe pump.After the fracturing experiment, the resins were fixed in the specimens and then the cut sections were observed under ultraviolet light irradiation. As a result, the hydraulically induced fractures, which were filled with the resin, are clearly observed. Detailed microscopic observations show that the main fractures are tortuous and are accompanied by many thinner ramified fractures. Additionally, fractured regions where the resin penetrates significantly are observed around the main fractures in the specimens fractured by the resin B. These induced fractures and fractured regions are considered to be the stimulated region in which permeability is improved. The necessity of estimation on the features of fracture tortuosity and ramified fractures is indicated for more accurate understanding of the well production and the stimulated reservoir volume."

Jan 1, 2015

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By M. Moats, J. A. Gonzalez

A review of operating practices in zinc electrowinning plants is presented in this paper. Surveys were sent to several zinc electrowinning plants and data provided by some of these plants was compiled in a database. Information about anodes and cathodes, electrolyte composition, stripping methods, cells, electrical systems, and additives was compiled and analyzed. From the data analysis, correlations between operating variables are presented. Recent trends in operational practices are also highlighted.

Jan 1, 2008

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

By C. Zangerl, T. Strauhal, S. Perzlmeier, M. Holzmann

"In high mountainous regions, deep-seated rock slides are often observed in foliated metamorphic rocks such as paragneisses, micaschists and phyllites. Given that comprehensive investigations of deepseated rock slides are extraordinary costly and therefore are rare, most studies are related to investigations in the surroundings of infrastructures and human settlements. In the framework of this study there is an excellent opportunity to gain new insights in the fundamental processes and mechanisms of slowly moving deep-seated rock slides from a case study in the surrounding of a large dam reservoir in Austria. New fundamentals for comprehensive slope stability analyses and hazard assessments and sound prognoses focussing on the long-term stability and deformation behaviour of slopes under changing boundary conditions (e.g. impounding of a reservoir) and/or concepts for mitigation measures can be obtained. Within this contribution, geological field surveys, deformation monitoring, geophysical and drilling data were analysed and presented. Based on the compiled and analysed data, some key-properties of the rock slide will be presented, whereby special attention will be given on the geometry and internal structure, the slope kinematics, as well as hydrogeological and geomechanical aspects.INTRODUCTIONIn high mountainous regions, deep-seated rock slides are often encountered in highly foliated metamorphic rocks such as paragneisses, micaschists and phyllites (Agliardi et al. 2012). Critical situations may occur when deep-seated rock slides fail in a rapid manner characterised by very high sliding velocities, and/or when they develop into long run-out rock avalanches. However, many rock slides in foliated crystalline rock masses either do not move at high velocities nor do they accelerate seriously and form extremely rapid slides. Displacement rates in the range of a few millimetres or centimetres per year are common for this type of rock slide (Bonzanigo et al. 2007, Tentschert 1998, Watson et al. 2007). Nevertheless, some case studies show an activity behaviour characterised by acceleration phases reaching velocities of even metres per day. However a slope collapse is not expected and these slopes decelerate to much lower base activities. The trigger for these phases can be manifold and include heavy rainfall and snow melt, initial reservoir impounding and water level fluctuations, changes in the slope’s equilibrium state due to antecedent slow deformation processes, ongoing erosion processes along the toe of the slope, and others (Zangerl et al. 2010)."

Jan 1, 2015

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada&apos;s current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today&apos;s commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By A. I. Gorshkov, Y. A. Bogdanov, O. Y. Bogdanova

Abstract - Detailed crystal-chemical study of iron and manganese oxides and some other minerals from low-temperature hydrothermal deposits in a newly discovered inactive mound in the TAG hydrothermal field were used to determine the precipitation sequence of mineral phases during lowtemperature processes and their post-sedimentary transformations. Particles of primary sedimentary X-ray amorphous proto-ferrihydrite with high silica content were replaced in situ by nontronite, ferrihydrite, or goethite during alteration. Ferrihydrite is the only proto-hematite phase. The transformation of the iron minerals, related to change in the physicochemical environment, is an important characteristic of low-temperature hydrothermal processes. The occurrence of hydrogenetic Fe vernadite and Mn feroxyhyte in the uppermost part of low-temperature deposits and bottom sediments near the base of the mound is evidence for cessation of low-temperature hydrothermal processes. Among the investigated mineral phases, goethite, nontronite, and hematite are stable in reduced sediments only.

Jan 1, 1999

By Theo Mayer

Presentation Outline Define data visualization in the context of workflow Present other industries? application and demonstrated benefits Provide conceptual tools to help you address a visualization strategy Hold 10,000 foot view ? to touch on many issues

May 1, 2008

By C. J. Kerr

"A recent information sheet from the Mining Health and Safety Branch of the Ontario Ministry of Labour was sent to all Ministry inspectors and engineers. The subject title was&apos; &apos;Two Brakes on a Hoist Carrying Persons"" and it quotes mining regulation 699, sub-section 206(i):No hoist shall be used for the transporting of persons unless it has a braking system consisting of at least two sets of mechanical brakes to stop and hold the drum for the shaft conveyance transporting the persons.The intent of the regulation is that each of these brakes is to be set so that, individually, they can safely stop the drum carrying persons and also hold the drum without movement with the maximum manload.This can be achieved in the following ways: Single Drum Hoist-one brake on each side of the drum, one brake on the drum, one brake on the pinion shaft, where disc brakes are used two separate disc brake assemblies on the disc. Double Drum Hoist, brakes on companion drum can serve as backup brake only pinion brake with one drum unclutched.Friction Hoist, one brake on each side of drum As new hoists can be manufactured easily with a two-brake system, attention will be focused on retrofitting pinion brakes to older hoists.A brake mounted on a pinion shaft is designed purely as an emergency brake in the event of main brake failure , controls malfunction, and power loss."

Jan 1, 1989

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland&apos;s copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982