Search Documents

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth's crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By Murray Pearson, Jack Murray

"The danger of autoclaves lies in the high temperatures and pressures that exist in autoclave vessels. The usage of autoclaves will continue to expand in the mining industry because of their efficiency and environmental friendliness. But increasing attention must be paid to ensuring their safety. Safety Instrumented Systems (SISs) play a critical role in autoclave plants by detecting potentially dangerous conditions, taking the plant to a safe state, informing the operator about the plant status and the cause of the trip and expediting safe plant restart. The SIS should ideally be fully integrated with but functionally independent of the Basic Process Control System (BPCS) and provide redundant logic solvers to increase safety and plant availability while reducing spurious trips.INTRODUCTIONWikipedia defines an autoclave as follows: “An autoclave is a pressurized device invented by Charles Chamberland in 1879 designed to heat aqueous solutions above their boiling point to process materials.” A typical autoclave system used in the metallurgical industry includes, besides the autoclave vessel, heat recovery (heater) vessels, high pressure positive displacement (HPPD) feed pumps, vessel lining systems, specialized internals and components, agitators, pressure letdown or flash vessels, isolation and control valves, over 2,000 I/O points and related instrumentation, and emergency relief systems."

Jan 1, 2009

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By A. C. Wilson

In 1991, local prospector C. ?Mickey? Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphite-inclusion riddled. In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1-kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage 2000). Since then, more than 36 occurrences of diamonds in bedrock have been reported in an approximately 30 km2 area centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last 5 years. Two of these kimberlites are diamondiferous. To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at $120 million (CAN). This paper summarizes the geological observations made on these occurrences and discusses including the relationship between the occurrences and the regional geology.

May 1, 2003

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By N. Kuyucak

"Acid mine drainage (AMD) is one of the most significant environmental challenges facing the mining industry worldwide. It occurs as a result of natural oxidation of sulphide minerals contained in mining wastes at operating and closed/decommissioned mine sites. AMD may adversely impact the surface water and groundwater quality and land use due to its typical low pH, high acidity and elevated concentrations of metals and sulphate content. Once it develops at a mine, its control can be difficult and expensive. If generation of AMD cannot be prevented, it must be collected and treated. Treatment of AMD usually costs more than control of AMD and may be required for many years after mining activities have ceased. Therefore, application of appropriate control methods to the site at the early stage of the mining would be beneficial.Although prevention of AMD is the most desirable option, a cost-effective prevention method is not yet available. The most effective method of control is to minimize penetration of air and water through the waste pile using a cover, either wet (water) or dry (soil), which is placed over the waste pile. Despite their high cost, these covers cannot always completely stop the oxidation process and generation of AMD. Application of more than one option might be required.Early diagnosis of the problem, identification of appropriate prevention/control measures and implementation of these methods to the site would reduce the potential risk of AMD generation. AMD prevention/control measures broadly include use of covers, control of the source, migration of AMD, and treatment. This paper provides an overview of AMD prevention and control options applicable for developing, operating and decommissioned mines."

Jan 1, 2002

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

By P. Keating, J. Goutier, J. Ayer

"New, high-resolution geophysical surveys were undertaken over parts of the Abitibi Subprovince, Canada, to help with geological mapping and to promote mineral exploration. Gravity surveys in the Rouyn-Noranda and Matagami areas (Québec) allowed better 3-D mapping of important geological structures, and a multiscale edge analysis of ground gravity data over the Blake River Group confirms that major faults behave at depth as predicted by surface geology. Airborne gravimetry west of Matagami (Québec) helped to identify a new trend south of Lake Grasset that is almost perpendicular to the assumed geological trend of the area. Electromagnetic (EM) surveys, flown in the Chibougamau (Québec) and Bartlett Dome (Ontario) areas, allowed new conductors to be identified at greater depths than were achievable with previously used EM systems. Airborne magnetic surveys were flown in the Burntbush area (Ontario), and other available high-resolution magnetic data were compiled to produce a continuous and homogenous magnetic grid of the Abitibi region.The resulting compilation map clearly shows the locations of dikes, faults, and shears zones, and reveals some fault extensions in areas of extensive overburden. This grid also allows the computation of enhanced maps, such as vertical derivative and tilt maps (e.g., a tilt map shows subtle magnetic features in the Blake River Group that are difficult to see in the total magnetic field or its first derivative). Results from these new surveys show there is considerable value in (1) resurveying areas covered by older surveys, and (2) recompiling data sets from these older surveys."

Jan 1, 2012

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By H. J. McQueen

ORDER OF PRESENTATION ?INTRODUCTION TO THE VICTORIA BRIDGE ?REASONS FOR A BRIDGE AT MONTREAL ?RAILROAD BRIDGE REQUIREMENTS ?IRON PRODUCTION CANADA / WORLD AL ?METALLURGICAL INDUSTRY CANADA ?FAIRBAIRN, STEPHENSON SHIP PLATE-RIB BOX GIRDER ?VICTORIA BRIDGE (PREFABRICATED BRITAIN) ?IRON ORE SITUATION THE VICTORIA BRIDGE 1859, TUBULAR -WROUGHT IRON* 1898, TRUSS ?STEEL* (*HOT RIVETED) 1957, SPUR, LIFT SPANS ??DUCTILE WROUGHT IRON WITHSTANDS FATIGUE ?TO KEEP THE TRAINS ON TIME & ON TRACK? ??IMMOVABLE SHARP PIERS SPLIT ?THE IRRESISTIBLE ICE, STOPPED CITY FLOODS? ? ?********* ??111 YEARS-YOUNG STEEL TRUSS, (1898): ?STILL VITAL SEA-T0-SEA RAIL LINK? ? ?********* ??51 YEARS HAVE PASSED SINCE SEAWAY (1958) ?SWITCHED BRIDGE INTO DOUBLE LIFT SPANS?

May 1, 2011

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009