Search Documents

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By Jeremy G. Berg, James B. Mulligan

"There is a very small fraction of wireless experts in the world with experience in underground installations and an even smaller fraction that have experience specific to building mine shafts. This is why in 2009, Redpath created its own system to meet the demands specific to shaft construction. Today, after a dozen shaft installations and several design iterations, Redpath has the expertise and experience required to implement a proper wireless system in any shaft configuration.This document will explain multiple proven wireless communication designs optimized for shaft construction and suitable for permanent use. This includes line of sight installations up to 1200m, short range mesh networks, and the latest patent pending Integrated Leaky Feeder Mesh Network. Additionally, this document will explore the lessons that Redpath learned in its effort to interconnect the people and tools needed to build a mine shaft.INTRODUCTIONAfter a decade of research, several design iterations and a dozen application examples, Redpath has resolved two wireless network architectures to best serve mine shaft construction projects.The long range line-of-sight (LOS) wireless network is the most cost effective and easiest to install, but requires an unobstructed line of sight between the working area and the shaft collar. As such, long range LOS is best suited for ventilation shafts or during the first phase of shaft sinking, before the shaft is equipped.Alternatively, a mesh network uses radios installed at pre-determined intervals in the shaft and on each conveyance. A wireless mesh uses antennas to bridge intervals between shaft radios, whereas Redpath’s integrated leaky feeder mesh network (patent pending) bridges these intervals with radiating cable, commonly referred to as a “leaky feeder” cable. Both of these mesh configurations can provide continuous reception for hoist conveyances travelling in shafts without line-of-sight, making them ideal for shaft equipping and even permanent installations in both mine shafts and lateral drifts.BACKGROUNDHoist operators receive operating commands using what are commonly referred to as “bell signals.” These instructions are delivered in a series of coded pulses on a spring returned pull cord or push button that is typically hardwired back to the hoist operator’s control room from one of many locations in the mine shaft. During the construction phase of a traditional mine shaft, a worker riding inside the sinking bucket would have to reach out to a pull cord installed on the shaft wall to send a stop command to the hoist operator. Today, Redpath’s modern shaft sinking projects use fully enclosed personnel carriers to protect the workers riding inside, specifically preventing workers from reaching out into the shaft while the hoist is in motion. The enforcement of this safety feature on all shaft projects in 2008 forced the engineering group at Redpath to find a suitable wireless solution for hoist communication to facilitate shaft construction.THE IDEAL COMMUNICATION SYSTEM FOR MINE SHAFT CONSTRUCTIONIdeally, the shaft communication system should not transform the tools to which the miners have grown accustomed. It should support the push-to-talk functionality of traditional VHF handsets and the standard belling system that has been used for decades. Additionally, it should be able to support a vendor independent framework upon which new devices and features can be added. The following paragraphs summarize some of the important requirements Redpath has identified.Support for voice transmission: Low latency is critical to prevent jitter during voice transmissions. The system must be compatible with commercially available mobile handsets and support several simultaneous conversations with the ability to broadcast a voice message to all users on a select channel using a “push-to- talk” microphone and loudspeaker.Transmission of PLC data: Low latency is required to"

Jan 1, 2019

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By G. Deschenes

"This literature survey discusses the recovery of gold from thiourea solutions. An overview of techniques used and general comments on the basic cyanidation methods are presented. The chemistry and mechanisms of cementation, activated carbon, resins, electrowinning, solvent extraction and pressure reduction are examined. Conclusions and recommendations give orientation for future research and development activities in this field.RésuméCette revue littéraire traite de la récupération de I ‘or des solutions de thiourée. Elle fait un survol de I ‘ensemble des techniques utilisées tout en introduisant des commentaires généraux sur la méthode classique qu'est la cyanuration. La cémentation, Ie charbon active, les résines, l'électroextraction, I ‘extraction par solvant et la réduction sous pression sont les méthodes analysées tout en considérant leur caractère chimique respectif ainsi que les mécanismes qui y sont rattaches. Des conclusions sont tirées et différentes recommandations sont suggérées pour orienter la recherche dans ce domaine."

Jan 1, 1986

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By M. Venkatraman

The limit of Hall - Petch relationship in ultra fine grained steels has been examined based on dislocation pile-up mechanism. When the grain size becomes small the dislocation multiplicity ceases resulting in very low work hardening rate in these materials. An approximate analysis of the theories of hardening indicates that H-P relation is obeyed up to 100nm. It appears that grain refinement is not the suggested approach to improve toughness as well as strength below a critical size.

Jan 1, 2004

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By H. Z. Liu, J. M. Zhao, F. C. Wang

"Novel silicate-alginate composite beads containing 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester (P507) were synthesized and applied for the adsorption of Nd3+ from aqueous solutions. The adsorption amount of Nd3+ has been increased owing to the introduction of P507. The effect of equilibrium pH (pHe), the kinetic and isotherm experiments were investigated. The adsorption reaches equilibrium at 9 h and the maximum uptake capacity is up to 195.4 mg/(g dry adsorbent). The Langmuir isotherm equations are used to describe the adsorption process. Complete desorption can be realized with 0.2 M HCl within 20 min. INTRODUCTIONRare earth elements (REEs) have found various applications in different domains, such as metallurgy industry, ceramic industry, nuclear fuel control, photo-electro-magnetic functional materials owing to their unique properties. Neodymium (Nd), as a representative of all of the most valuable REEs, is widely used as catalysts, laser crystals, capacitors, rubber additives, Nd-Fe-B magnets, hydrogen storage and so on. Thus, the separation and purification of neodymium is significant. Unfortunately, Nd always coexists with other REEs and selective separation of the individual Nd from the REEs mixtures is still extremely difficult owing to their strictly similar atomic structures and chemical properties.Liquid-liquid extraction (LLE) and solid-liquid adsorption (SLA) are the most widely adopted techniques for the separation of REEs in the hydrometallurgical fields. The LLE process is well suited for large-scale continuous operation because of its inherent high capacity and fast kinetics. Nowadays, as a commercial extractant, 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (P507) has been extensively studied for extraction and separation of REEs since it has considerably good extractability and high separation efficiency (Xu et al., 1992). SLA is one of the effective and green separation methods with some prominent advantages, such as easy regeneration of adsorbents, small footprint size, less industrial wastes, higher enrichment factors and column efficiency,rapid solid–liquid separation without emulsion and so on. Hence, the introduction of extractants with excellent performance into adsorbents will integrate the advantages of LLE and SLA (Lee et al., 2009)."

Jan 1, 2012

By H. O. Seigel

Induced Polarization includes many types of dipolar charge distributions set up by the passage of current through consolidated or unconsolidated rocks. Among its causes are concentration polarization and electrokinetic effects in all rocks and the phenomenon of Overvoltage in rocks containing electronic conductors such as metallic sulphides and graphite. In normal rocks the polarization effects may be usually con-fined within relatively narrow limits and any large departures may be at-tributable to the presence of electronic conductors. In practice, Induced Polarization is measured in one of two ways. In the first a steady current of some seconds duration is passed and abruptly interrupted and the slowly decaying transient voltages existing in the ~round are measured after interruption. This is known as the "pulse", "transient", or Direct Cur-rent Induced Polarization (D.C.I.P.).The second method entails a comparison of apparent resistivities using sinusoidal alternating current of two or more frequencies, generally within the range of 1/10 to 10 c.p.s. Induced Polarization extends the

Jan 1, 1962

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By M. Brochu

In this paper, we present a computer-vision approach developed for wall-thickness measurements of corroded pipes inspected by double-wall radiography. The main objective of the work is to optimize data collection and film interpretation using computerized image analysis. To date, the system is able to identify the inner and outer contours of a pipe and perform wall thickness measurements at each pixel of a radiograph. This will be presented by analysing pipes having different dimensions. Another important feature of the system concerns the algorithms' adaptability to pipe wall texture. In other words, image analysis is automatically refined around rough or corroded areas. This allows more precise thickness measurements and shape identification in critical sections as will be demonstrated with examples. Finally a brief overview of results exploitation will be given and compared with human interpretation. It will show the reliability of automated image analysis and the many possibilities offered by complete output analysis.

Jan 1, 2005

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By R H. Hallam

The Mattagami mining district encompasses a favour-?able belt of folded Keewatin-type rocks, with intercalated sediments and intrusives of late Keewatin age. This environment has been subjected to periods of basic and acidic intrusion. The orebodies lie within the fold structure and are associated with faulting and shearing of considerable magnitude. The No. 1 orebody contains 60 to 70 per cent massive sulphides. The minerals, in their order of abundance, are generally: pyrite, sphalerite, pyrrhotite, magnetite and chalcopyrite. It is evident that the broad geological structure of the district is amenable to ore deposition. There are two ? prominent linear expressions which comprise this broad structure. Both strike directions lie at the edge of, or are related to, a complex gabbro-anorthosite-peridotite zone. The fact that eleven of the ore zones discovered to date coincide with the broad structure indicates its over-all importance. It is estimated that the production from Mattagami Lake Mines will be in the range of 600 to 700 tons of zinc concentrate and 70 tons of copper concentrate per day.

Jan 1, 1964