Search Documents

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

A study was made to determine the effect of increasing concentrations of dissolved oxygen on the floatability of galena pyrite and chalcopyrite. Adsorption, flotation and contact-angle tests were done in deoxygenated, in air-saturated and in oxygen-saturated solutions. The results showed that the adsorption of collector increased as the concentration of oxygen increased. Adsorption followed the exponential law r = kC'/"• Discontinuities in the curves were observed after the adsorption of several monolayers of collector. Although adsorption increased with increasing oxygen concentration, the floatability of the pyrite minerals did not increase, because oxidation had adverse effects on the floatability of these minerals. The floatability of galena was maximum in oxygen-saturated solutions, pyrite was depressed and chalcopyrite was also slightly depressed. Contact-angle tests proved that a bubble could not be attached to large flat surfaces in deoxygenated solutions, because sufficient surface free energy was not available for adhesion after the deformation of the bubble. In the presene of air, all the minerals yielded the same maximum angle of 72 degrees, characteristic of isopropyl xanthate.

Jan 1, 1970

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Serena Biella

Gold has received a growing interest as a catalyst for the selective oxidation of organic molecules using oxygen under mild conditions1. In the liquid phase application small gold particles (2.5-7 nm) deposited over different solid supports can be used but, like many other noble metals, their catalytic activity depends upon the nature of the support and the preparation metod2-5. In particular, gold on carbon is the preferred catalyst for the oxidation of the alcoholic 2-7 and the aldehydic7-9 groups and one of the best preparation method is the immobilisation of colloidal particles2-5,8,9. Suggested application of gold catalysis in fine chemicals production, tested on laboratory scale preparations, is reported in table 110. In order to produce more efficient catalysts for the liquid phase oxidation and to derive new insights into the reaction mechanism, we have made a comparison among catalytic systems based on different metals. The first effort was to test the activity, if present, of naked metal particles and then to study the influence of various materials commonly used as a support.

Oct 1, 2003

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By J. A. Morgan, P. M. Dimmell

Abstract - The Aubry pegmatites are located on the Seymour Lake property, 15 km north of Lake Nipigon in northwestern Ontario. The property lies within the Caribou Lake-Marshall Lake greenstone belt along the English River-Wabigoon subprovince boundary of the Superior province of the Canadian Shield. The property was optioned in March 2001 by Linear Resources (now Linear Gold Corp.), who carried out gridding, prospecting, geological mapping, soil and lithogeochemical sampling, trenching, channel sampling, and a total of 1,866 m of diamond drilling in 32 holes. The Aubry pegmatites are classified by Breaks et al. (2003) as complex type, spodumene-subtype, lithium-cesium-tantalum pegmatites (Cerný, 1989). These pegmatites generally form under high-pressure-low-temperature conditions, display complex internal zoning, have relatively low Nb/Ta ratios in the ore-forming assemblages, and contain significantly elevated tantalum values (Cerný, 1989). Other examples of spodumene-subtype pegmatites include the formerly producing Hugo pegmatite in South Dakota, and the currently producing Greenbushes pegmatite in Australia. The Aubry pegmatites occur as an undulating system of stacked sheets that dip moderately to steeply eastward over a 1-km strike length. The main portion of the North Aubry pegmatite ranges in true thickness from 10 to 28 m over a strike length of 125 m, whereas the thickest portion of the South Aubry has an estimated true thickness of 15 to 16 m over a minimum strike length of 95 m. The North Aubry pegmatite remains open downdip and along strike to the north, whereas the South Aubry pegmatite remains open downdip and along strike in both directions. The Aubry pegmatites are among the most highly evolved in Ontario, with the southern end of the North Aubry (trench 5/6 area) being the most highly fractionated (Breaks et al., 2002). Channel samples from the trench NA-5 area of the North Aubry pegmatite produced values up to 2.49 wt.% Ta2O5 over 4 m. Coarse manganotantalite crystals, up to 5 cm in diameter, from this trench contain up to 84.9 wt.% Ta2O5 (Breaks et al., 2002). Drill hole SL02-31 in the trench NA-6 area gave values of 0.046 wt.% Ta2O5 over 17.7 m, including 1 m @ 0.464 wt.% Ta2O5. Further exploration will focus on defining the grade of the North Aubry zone, extending and defining both known pegmatites, and identifying additional Ta-rich zones within them. Lithogeochemical and enzyme leach soil geochemical data suggest the presence of multiple undiscovered pegmatites on the property.

Jan 1, 2005

By O. Herstad, J. M. Toguri, K. Grjotheim

DURING the last three years, investigations on the aluminum reduction of magnesium-bearing compounds have been initiated at the Institute of Inorganic Chemistry, The Technical University of Norway. The results of these investigations are reported in this paper. Very little information exists in the literature on the reaction between magnesium compounds and metallic aluminum. The available information itself is conflicting, and, to clarify the existing discrepancy, the reactions between aluminum and magnesium oxide (MgO), caJcined dolomite (CaO . MgO) and olivine (Mg2SiO.) were studied. The logical approach for the study of these reactions between condensed states with the formation of a gaseous phase is, ( 1) the measurement of the equilibrium vapour pressure of the gas, in this case magnesium, associated with the respective reactions and, (2) the identification of the end products of the reaction in order to establish the re-action scheme.

Jan 1, 1962

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By W. E. Bawden

Situation: Creighton mine, situated about twelve miles west of Sudbury, Ont., on the Algoma Eastern railway, is owned and operated by the International Nickel Company, incorporated in the United States under the laws of New Jersey. The ore is smelted at Copper Cliff, near Sudbury, and the matte is refined at Port Colborne, Ont., on lake Erie. Geology: The ore occurs in what is known locally as 'the basin' near Sudbury (Figure 1) the central part of which is composed of the Animikie series of sediments, consisting of sandstones, slates, tuffs and conglomerates. The basin is about 16 miles wide and 36 miles long. The Animikie sediments are surrounded by a sill of norite - a gabbro rock in which the pyroxenes are orthorombic. On the outer contact of this norite the sulphide deposits occur and the Creighton deposit, similar to others, lies on the southern edge of this basin. There are two orebodies at the Creighton, the upper one called the footwall orebôdy, and the lower one the hanging-wall orebody. The hanging-wall of both of these bodies is norite, and the footwall of the upper one is granite. The two are separated by an intrusion of greenstone which forms the footwall of the lower body. The ? maximum length of the deposit is 1000 feet and the maximum width is approximately 300 feet. It narrows at the ends and is somewhat lenticular in shape. The dip is about 45 o to the west, and the strike is north and south. The orè is a mixture of three minerals - pyrrhotite, chalcopyrite and pentlandite. The pentlandite, which is distinguished by its cleavage from the other two, is apparent to the naked eye only in the lower orebody and is more finely disseminated in the upper one. The lower body contains a little higher percentage of nickel.

Jan 1, 1925

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By L. G. Smith, C. A. Shook, W. H. W. Husband, W. Schriek

"The flow of slurries in pipelines is governed by many variables, and the study of the influence of each of these variables is difficult, if not impossible, in some cases. Many correlations are available which fit data within a given range. However, no one method is yet available to design a slurry pipeline for all desired conditions without at least some physical measurements on the slurry itself. For this reason, the slurry pipeline facilities at the Saskatchewan Research Council have been developed during the past 12 years and it is hoped that the development will continue until the process is thoroughly understood and test facilities are no longer necessary. This paper outlines methods currently used and under development at the Saskatchewan Research Council for measurement, control and study of the variables governing the flow of slurries."

Jan 1, 1973

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015

By W. B. Boggs

This is a rather comprehensive subject and cannot be thoroughly covered in the short rime allowed for its presentation. This article will touch only upon a few of the chief points of the difficulties encountered in recovering copper from brass shell cases in a primary smelter which was not designed to treat scrap metals. Owing to the fact that the plant is at present (Dec., 1946) closed, and our tests were not completed, full details of the results are not available. As is well known, most primary smelters are situated near the mines in the interior of various countries and are not close to seaports or large industrial and railway centres. Consequently, iris unusual for a primary smelter to be asked to treat scrap metal of any kind. When so required, iris obvious that the primary smelter is at a great disadvantage, for the simple reason that it probably has to pay the freight on the scrap from the seaport or industrial centre to the smelter and then also pay the freight on the recoverable metal from the smelter to the refinery, or seaport or industrial centre. Another disadvantage is that a primary smelter is not equipped to sample and unload the scrap nor bas it usually the equipment adaptable for treating the scrap efficiently, as the plant bas been designed to handle large tonnages of ores and concentrates. This short paper will describe some of our difficulties> and how they were corrected. However, it might be advisable to state briefly some of the methods used in treating brass shell cases in other plants. In the first place, a brass plant producing new brass- especially those producing brass billets for extrusion to make brass tubes or rods, or to be drawn into wire, or making brass cake to roll into brass sheets- generally insists upon using new electrolytic copper and zinc and is opposed to using any scrap or secondary brass . Consequently, such a plant usually will not treat brass shell cases. Therefore, the usual procedure is to ship brass shell cases to a secondary smelter, where it is generally sorted, melted, fire-refined, and returned to the market in the form of a high or low brass ingot which can be sold to brass foundries for making brass castings. This evidently is the cheapest and simplest method. Another method is to ship to a smelter which is a combination of a primary and secondary smelter attached to or near an electrolytic refinery. In plants of both these types, that is a primary smelter with Cottrell dust collectors or a combined primary and secondary smelter with Cottrells or a bag house, the zinc may be wasted. However, if a bag house is used, some of the zinc is recovered, but it is usually contaminated with other metals and further processing is required to recover it.

Jan 1, 1947

By Hans D. Gougar

To meet an increasing demand for minerals, mining operations are moving to ever more remote regions. The lack of a local energy supply and infrastructure, coupled with social and regulatory demands for lowered environmental impact of mining operations, presents an opportunity for a seemingly unlikely competitor ? a nuclear power plant. The Modular Pebble Bed Reactor concept, currently in various stages of research and development around the world, offers a high degree of reliability and safety with minimal consequences for the local or global environment. The passive safety features of this design eliminate the need for the extensive active safety systems that add significantly to the cost of current water-cooled reactors. With the MPBR, as with all nuclear plants, there are no appreciable quantities of waste products released to the environment during normal operations. In contrast with conventional reactor designs, the MPBR would also remain radiologically safe even under the most severe abnormal circumstances. The key to the design is the fuel element. Enriched uranium microspheres are coated with various layers of pyrolytic carbons and silicon carbide to form a highly-temperature resistant particle that effectively retains all fission products. These particles are mixed with graphite and formed into 6 cm pebbles. A randomly packed vessel of such pebbles forms the reactor core through which helium is circulated as a coolant. Computer models and tests performed on actual pebble bed reactors confirm that fuel failure temperatures are not reached even during the most severe conceivable loss of coolant accident. The reactor drives a gas turbine cycle with resulting efficiencies as high as 48%, comparable to natural gas-fired units. The low price of uranium fuel and low maintenance requirements translates into competitive operating costs. However, high capital costs prevent the MPBR from competing with natural gas in most markets. In remote applications where no fossil supplies are readily available, the playing field is more level. This paper summarizes the features of two of the more promising candidates for remote applications and discusses the strengths of the MPBR from the perspectives of fuel supply and environmental impact.

May 1, 2002

By Ian E. Efford

The paper gives an assessment of Canada's energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada's energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013