Search Documents

By F. R. Archibald

IN a recent paper on Roasting of Beattie Concentrate (1), the importance of controlling the temperature, and the sulphur dioxide concentration was pointed out. It is the purpose of the present paper to present further information by which the most satisfactory conditions for roasting are more specifically defined. Incidentally, a method of illustration is developed for representing roasting curves on a three-dimensional diagram. The primary purpose of this investigation, as in the case of the earlier work, was the search for information that would be of practical value in improving plant operation and gold recovery. For this reason, emphasis is laid on the regulation of essential variables and on definition of their optimum values and limits for maximum gold recovery in the subsequent cyanidation process. Good roasting is considered at least as much an art as it is a science, and, in this light, theoretical consideration of the nature and sequence of the chemical reactions involved is of secondary importance. The presentation which follows includes a series of graphical illustrations, an interpretation of the graphs, some theoretical considerations, and a description of laboratory technique.

Jan 1, 1940

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By Charles Camsell

THE Northwest Territories covers a very large area-more than one-third of all Canada-and its most northern point, Cape Columbia in Ellesmere island, is distant only 500 miles from the Pole. Our first knowledge of the Arctic Archipelago, of which Ellesmere island forms a part, resulted from a gold-mining venture in Queen Elizabeth's reign. The English navigators of that time were eager to find a north-westerly and shorter and Jess hazardous route to the riches of China and Japan than that which Magellan had discovered, but they were unaware that the continent then known to bar a direct route extended in great width far to the north. Frobisher was one of these navigators. He reached in 1576 the bay in Baffin island now named after him, convinced that he had found a passage connecting the Atlantic with Asiatic seas. Forced to re-turn after ordeals in which ice, wind, and Eskimos flayed formidable parts, he brought back, among other novelties, a piece o black stone which had been picked up casually by one of his officers, and gave a little of it to the wife of one of the venturers, or financial backers of the enterprise. To quote now from Hakluyt: ? 'She by chance threw and burned it in the fire so long that , at length being taken forth and quenched in a little vinegar, it glistered with a bright marquesset of gold. Whereupon the matter being called in sorne question, it was brought to certain goldminers in London to make assay thereof, who indeed found it to hold gold and that very richly for the quantity." On the strength of this, the venturers, anticipating much profit, launched a second expedition to secure more of this stone, and 143 persons, including 14 miners and finers, set forth in 1577 and returned the same year, with, however, 200 tons of another mineral. Influenced by glowing accounts of veritable mountains of this mineral and by assays made after "additaments"-that is how "salting" in those days was described-the venturers, including Elizabeth, supplied funds for erecting a smelter and refinery at Dartford and outfitting a stilllarger expedition. And so, in 1578, fifteen ships departed with the Queen's blessing, for the same remote shores. After many mishaps, they returned with over 1,000 tons of the mineral, but when it yielded very little of value at the works in Dartford, the? Company of Venturers was forced into liquidation. Though our first prospector and miner was rather inconsiderate of the investors, he proved the existence of an archipelago, hitherto unknown, and secured much information about the new land and its dwellers.

Jan 1, 1938

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By R. C. Wallace

Since the time when Canada's East and West were joined by the railway, and communication was established into the interior, settlements grew on the southern fringe of the great Precambrian area that formed the northern protaxis of the continent during its vicissitudes of growth. They clung precariously to the fringe of that ancient land, for the Precambrian is not generous to those who wish to live by the fruits of the soil, except in those limited areas where the Pleistocene ice-sheet has been profuse in its gifts of clay to cover the hard surface of the Precambrian rock. Later settlements spread westwards over the expanse of Cretacean plains that now form the wheatfields of the Canadian West; but there still remained in northern and western Ontario, in eastern and northern Manitoba, a pioneer race, to whom agriculture had attractions only in so far that it provided the wherewithal to lay siege to the riches of the Precambrian. And they had a vision beyond their time. More than they knew, they had seized the fact that for the complete rounding out of Canadian national life, a8 well as for the establishing of the necessary contributions towards the economic stability of Canada and its provinces, an industry in mining sh01.dd be well and truly built in the hinterland of the central provinces. Failing the winning of mineral from the rocks, and timber from the forests, there would remain between the East and the West an enormous barrier of unproductive country which would not only be an incubus to the agricultural people in their struggle for economic liberty, but would effectively, and for all time, remain an un-populated void across which the aspirations of East and West would be unable to unite.

Jan 1, 1924

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By K. G. Chipman

The Geological Survey is the oldest map making department in the Canadian Government service, and when organized in 1842, one of the first principles to be recognized was the absolute necessity of having good maps. The primary purpose of the Survey has always been geology; but because a graphic representation by means of maps makes the written report .more readily intelligible; because the correlation of known geological facts is often difficult or nearly impossible unless they can be represented on a map; and, because the public demand information shown in this way, the Geological Survey must continue to supply maps; and the supplying of these maps must be considered as an essential part of the work of the Survey. It is a commonly recognized principle of pedagogics that an appeal to the eye is quicker than one to the ear; that children (and others) learn more quickly when a thing is presented to them through the eye rather than through the ear. The application of this principle to the work of the Geological Survey is that, to a large number of people, the message of a map is more quickly grasped, is more readily intelligible, and is in many ways of more interest and value than is the same information in a report. I do not mean that the maps are of more importance than the reports.

Jan 1, 1924

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By Jean A. Bastien

Cette présentation décrit les étapes de développement et l?exploitation souterraine au puits Penna chez Agnico-Eagle division Laronde. Les sujets suivants sont touchés : le fonçage du puits, le développement des niveaux, la méthode d?exploitation, la manutention de la roche brisée, le méthode de remblayage et la ventilation. En résumé : le fonçage du puits s?est fait sur 2,240 mètres de novembre 1995 à mars 2000. Le développement des niveaux a débuté en octobre 1998. Les opérations de minage ont débutés en août 99 dans le premier horizon situé au dessus du niveau 122. Les chantiers sont exploités par longs-trous d?environ 25 mètres de long avec un diamètre de 10 cm. Les accès à la zone minéralisée sont transverses. Le minerai est soutiré des chantiers et acheminé au passe-minerai a l?aide de chargeuses navettes. Par la suite, le minerai passe sur un marteau, est concassé et transporté sur un convoyeur, jusqu?au silo de 4,500 tonnes au-dessus de la station de chargement automatisée du niveau 152 d?ou les skips sont alimentés. Le remblai en pâte est envoyé de la surface par des trous ayant un revêtement d?acier. Le diamètre intérieur est de 15 cm. Le réseau de ventilation est principalement alimentée par des ventilateurs de surface (système aspirant et souflant) conçus pour acheminer sous-terre un maximum de 640 mètres cubes par minutes (1,350,000 pcm).

May 1, 2001

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By P. E. Cavanagh

"The Davis tube test has been used for many years as a laboratory method for determining the magnetic iron re-coverable from a magnetite iron orebody. This paper de-scribes a method for determining the recoverable iron from ores of the Labrador Trough type, with the usua1 flow sheet utilizing spirals followed by magnetic separation.The mechanical structure of a metamorphosed iron ore, resulting from recrystallization over long periods of time, is the basis for the laboratory method developed. Similarities between the structures of such recrystallized ores and the structure of annealed and recrystallized steel are noted.A laboratory technique to determine the size of the different grains of gangue and iron ore minerals is de-scribed and the application of this information to arrive at recommended grinding techniques and flow sheets is demonstrated. The use of the method to determine recoverable iron in such ores is compared to actual iron recovery in the pilot-plant and commercial concentrations of the same ore.The use of a specified lower limit of recoverable iron as determined by this method, in order to design open-pit limits, achieves practical results when compared to designing a pit based on an arbitrary lower limit of total soluble iron. The Ungava Iron Ore deposits are used in giving an example of the resulting pit design changes."

Jan 1, 1968