Search Documents

By R. Laucournet, E. Billy, M. Joulié

Today Li-ion batteries are considered as one of the most attractive available energy storage solutions. However in order to overcome environmental, legislative and economic issues, the management of used batteries has to be considered and mainly the recycling. The present paper deals with the recycling of used Li-ion batteries and the recovery of high value metals from active materials of electrodes. Lithium nickel cobalt aluminum oxide (NCA) and lithium manganese nickel magnesium oxide (LMNM) cathodes, which contain most of valuable elements typically used in the composition of active materials for Li-ion batteries are investigated by a hydrometallurgy route. The process is divided into two steps: the materials leaching and the elements recovery by a selective chemical separation. Some experimental parameters (acid nature, concentration, time and temperature) are studied to determine the most efficient conditions of dissolution. Then, the valuable elements such as nickel, cobalt and manganese are selectively recovered with a high efficiency close to 100 % and with a high purity by precipitation. By this study, an adaptable hydrometallurgy process can be defined according to the composition of Li-ion batteries to recycle.

Jan 1, 2014

By R. Lasmanis

"Washington State's diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By Robin Sheremeta

What is the goal of every organization when it comes to safety? Everyone Going Home Safe and Happy Every Day Good old days: Era of Death (accidents will happen) Era of Engineering: (Eg. hand rails, limitswitches, machine guards, etc.) Era of Legislation: procedures, laws and regulations (Eg. SWP?s, Mines Act) Era of Behaviour-Based Safety: (eg. STOP program)

May 1, 2010

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By L. J. Han, Y. J. Zong, S. Y. Wen, J. J. Wei

"Stress strain curves characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states were analyzed through triaxial compression tests carried on using TAW-2000 microcomputer control electro-hydraulic servo rock triaxial test system. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression was split failure paralleling to the axis of samples, while macroscopic failure forms under uniaxial compression was shear failure, the shear failure angle of which decreased linearly with confining pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressure, and then based on acoustic emission damage and volumetric dilatation damage the damage evolution properties of samples were analyzed, and damage constitutive model were established, realizing the real-time quantitative evaluation of samples damage state in loading process. INTRODUCTIONDamage is a phenomenon that micro defects in material under monotonic loading or reloading will lead to progressive decrease of the cohesion and damage of volume units. Many scholars at home and abroad have carried out systematic researchers on damage evolution characteristics and constitutive model of rock, and have achieved a series of remarkable results in this field. Lu Y.D. (2004) studied the complete stress-strain curve’s characteristics of marble under triaxial compression, and established the bilinear elastic-linear strain softening-residual ideal plastic damage constitutive model. Ren J.X. (2001) studied the damage evolution laws of coal and rock mass by computerized tomography triaxial loading system, realizing the quantitative evaluation of damage state. Zhang Z.L. (2011) studied the deformation and failure mechanism of strong weathered sandstone by triaxial compression test, and analyzed the damage evolution processes and established the damage evolution equations based on the density method. Li X.J. (2012) studied the microscopic damage characteristics of siltstone under triaxial compression by scanning electron microscope and digital image technology, and analyzed the statistical distribution characteristics of cracks azimuth angle, length, width. Zhou J.W. (2012) studied the strength, deformation and fracture damage characteristics of sandstone by uniaxial cyclic loading and unloading tests, and defined damage variable based on linear damage mechanics theory and acoustic emission (AE). Cao W.G. (2006) established a new damage model and a statistical damage constitutive model of rock under specific confining pressure according to the force of damaged part and undamaged part in rock on the base of statistical damage theory. Li S.C. (2014) studied the damage evolution characteristics in the whole uniaxial compression process of sandstone by electrical resistivity and AE, and proposed a status qualitative criterion for rock damage."

Jan 1, 2015

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By M. Savella

The Runruno Gold Project is located on the island of Luzon, approximately 200 km north of Manilla in the Philippines. The mine is a surface mine operation and use the proven BIOX® and carbon in leach processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces of gold, and the operation will produce 96,700 ounces of gold per annum over a mine life of 10.4 years. The BIOX® circuit is designed to treat 140,000 tpa of concentrate with a design capacity of 404 tpd of concentrate at a design sulphide sulphur grade of 17% S2-. The Runruno project is the first BIOX® plant to implement the Generation III BIOX® design principles. As part of the Generation III BIOX® program Outotec supplied a turnkey, containerised metallurgical laboratory to facilitate the first four stages of the BIOX® and ASTER™ inoculum build up requirements. BIOX® inoculum build-up was started during early January 2015 with 5 litres of stock cultures shipped from South Africa. The BIOX® culture was successfully adapted to concentrate produced from the mini plant during March 2015. The ASTER™ inoculum build-up commenced during early August 2015 utilising 27 litres of ASTER™ bacterial inoculum already adapted to similar process conditions expected during commercial operation. This paper will detail the various stages of inoculum build-up through to commissioning and ramp-up of the BIOX® and ASTER™ Processes at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX® design principles.

Jan 1, 2017

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015

By N. Dufresne

"The evolution of mining methods at Brunswick Mining and Smelting shows that, in the case of a large deposit, technology must adapt itself to changing conditions. As problems are encountered, management must modify their approach if they hope to meet production quotas. This search for new and better ways started with the opening of the No. 12 orebody and is still going on today.From large-scale open stoping, the Brunswick Mining and Smelting operation went to transversal cut-and-fill, then to longitudinal cut-and-fill, which is the main mining method now employed. However, to solve certain problems experimenting with Avoca methods was initiated. Rebar grouting and prepinning have also made significant contributions toward securing relatively poor ground in the hanging wall and holding badly fractured backs in wide stoping areas. Introduction In 1952, M.J. Boylen had incorporated Brunswick Mining and Smelting Corporation Limited to develop his recently found No.6 and No. 12 orebodies near Bathurst, New Brunswick. Between 1953 and 1957, St. Joseph Lead Company was brought in to try and initiate mining . During those years, St. Joseph Lead sunk two shafts at No. 12-No. 1 to 425 feet below surface and No.2 to 982 feet. They also developed the 200 and 350 levels to sample the ore at depth and operated a 100-tpd pilot plant at the No.6 mine. However, due to low recoveries and depressed metal prices. the project was shut down in 1957.A group including M.J. Boylen. K.C. Irving. Maritime Mining Corporation and Patino Corporation reacquired the property from St. Joseph Lead Company in 1961. New financing was arranged involving La Societe Generale des Minerais, S.A . of Belgium and Engineering Consultants Limited of Saint John. New Brunswick. During the years 1962 and 1963, construction of surface and underground facilities progressed rapidly."

Jan 1, 1981

By Donald E. Archibald, Gerald A. Allcott

"Noranda's Heath Steele Mine is located 35 miles north of Newcastle in northern New Brunswick. Blasthole open stoping with partial delayed filling is the major mining method in use. The selection of stope and pillar dimensions to ensure mine stability was originally subjective. This paper describes the progress made in attempting to rationalize design.One major feature is the fracture pattern. The main orebody now being mined, the B zone, has undergone five periods of folding and each period of folding developed a family of fracture planes which are axial planar to that particular fold pattern.The other major features considered are the calculated increase in stress due to mining and depth and its relationship to measured strain. Experience has shown that ground problems affecting production have usually originated in rib pillars. Field observations of ground deterioration and multi-wire extensometer measurements of strain are tabulated together chronologically for each pillar.A factor representing stress and a common plane of weakness are identified. Graphical analysis is used to determine the effect of the plane of weakness on a typical stress/strain curve and provides a base for the design of pillars."

Jan 1, 1981

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By J. C. White

This paper, after a brief introduction giving the history and geology of the area, deals with mining operations at the Copper Mountain mine of Gaspe Copper Mines, Limited. It discusses development operations, and then goes into the mining methods employed, covering drilling, grade control, blasting practice, loading and hauling, and the road and service machines used.

Jan 1, 1969

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004