Search Documents

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By J. Jung, W. Keller, N. Rohn

In hydrometallurgical minerals processing slurries are often processed at very small grind sizes and high solids concentrations. This normally results in flow anomalies of such slurries. Due to flow limits or yield stress the slurry tends to stagnate close to the vessel bottom, the walls and at any internals. The main mixing task therefore generally is not suspending of the solids but the homogeneous blending of the entire vessel volume. If not considered during the agitator design only a fraction of the vessel contents will be mixed. Therefore the knowledge of the slurry rheology as well as the variations in process parameters is vital to design e.g. storage or surge tanks. The integral mixing solution considers the motor power, the choice of the impeller type and number, the impeller diameter as well as the design of the baffles and feed and discharge positions.

Jan 1, 2014

By Sazol Das, Hany Ahmed, Ganesh Bhaskaran, Zhuoru Wu

"Friction stir welding (FSW) process in lap configuration for dissimilar materials has been developed and tested for steel to aluminum joining. A novel cylindrical tool was designed for improved material flow. The joining of steel to high strength 5xxx and 6xxx aluminum was carried out by FSW technique using optimized process parameters. The microstructure, micro-hardness, joint strength and corrosion properties at the weld interface have been investigated. Optical and scanning electron microscopy reveled a well layered structure at the interface and lap shear tests of the welds showed excellent fracture resistance. Neutral salt spray tests for up to 500 hours (ASTM B117) were carried out on the bare steel to aluminum FSW joints, which did not show neither evidence of corrosion at the weld interface, nor any degradation of the weld strength. The FSW lap configuration was applied to prototype commercial vehicle structural component whereby a steel stiffener insert was friction stir welded to high strength 6xxx aluminum alloy. The interface microstructure showed layered root without any steel shattering in aluminum side. A finite element study was carried out to quantify the benefits where it was found that the stiffness increases by 76% under bending loads and 36% in torsion loads.INTRODUCTION Energy preservation and environmental issues, namely carbon footprint and legislation around emission in transportation industries has led to a growing need to use of lightweight materials such as aluminum and magnesium alloys along with various grades of steel in structural application, while still maintaining their strength and crashworthiness. Assembling dissimilar materials within integrated structure is thus a stringent requirement related to optimum performance. In order to achieve an efficient technology of joining dissimilar materials such as aluminum to steel, it remains difficult to select an effective welding process for a given joint configuration. The use of aluminum in transportation industries for structural component is not exclusive in a design and is almost always used along with various steel grades for a mixed materials solution, thus dissimilar aluminum/steel lap joining is of great interest since this is widely used in the assembly of parts (e.g. pillar, frame rails, chassis, body in white (BIW), CAB, etc.)."

Jan 1, 2018

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By H. R. Huffman

"This paper reviews the history of iron powder production, and outlines the varions production methods. The uses of iron powder and the reasons for its use are also covered. The paper concludes with a look at future trends in powder metallurgy.INTRODUCTION TO POWDERSTHE IRON POWDER INDUSTRY is enjoying a very rapid growth. The annual consumption of iron powder is now at the 100,000-ton level, twenty times higher than it was at the end of World War II, and the yearly in-crease bas been almost consistent at 20 per cent. This is expected to increase, bringing the tonnage to 200,-000, or even (according to some experts) to 270,000, in 1970. In any event, powder metallurgy is expanding at high speed and making an important impact on the production of iron and steel products. Some indication of the faith in the future market may be indicated by the commencement of three new powder production plants in Canada with a total capacity of 136,000 tons annually."

Jan 1, 1969

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

By M. Saghaeian, R. Hejazi, Fakoor Sanat Tehran Company, H. Abedini, M. Zare

"Dewatering of final tailings is one the biggest issues in iron ore processing plants. Because of the fine and hydrophilic particles in the iron ore tailings, dewatering of such material is difficult and, in most of the cases, needs to be processed using expensive and complicated equipment. In this study, a novel method based on classification of small and large particles has been proposed to improve the dewatering performance of iron ore tailings. In the proposed method, a hydrocyclone has first been used to separate the fine and coarse fraction of iron ore tailings. Then, the coarse fraction (hydrocyclone underflow) is easily dewatered by using vacuum belt filter. Then, the fine fraction (hydrocyclone overflow) is primarily dewatered by using a high rate thickener. Finally, the thickener underflow is added to the bed of solids on the same belt filter, which is used for dewatering of hydrocyclone underflow. The efficiency of this method has been compared with other solutions for tailings dewatering including changing vacuum filtration parameters, using fabric with larger pore size, and using pressure filtration, all through laboratory scale experiments on the tailings of an iron ore processing plant in Iran. The results indicated the superiority of this method compared to the other ones, which increased the specific filtration capacity of the tailings by around 46%.INTRODUCTIONWet beneficiation of minerals requires a substantial amount of water to enhance the efficiency of the process. Used water should be recovered at the end of process to minimize shipping costs, meet contract specifications, and reuse process water (Wills and Napier-Munn, 2006). Dewatering equipment is usually divided into sedimentation (thickening) and filtration (pressure and vacuum) equipment, the choice of which depends on particle size, solid content of slurry, and material nature (Mular et al., 2002)."

Jan 1, 2016

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By L. D. Eccleston

Any man-made structure will eventually decay, but we are basically concerned with the prevention of corrosion within a fairly limited time span. How corrosion can be minimized by design, the removal of oxides and a careful choice of paint systems is discussed, and mention is made of the electrical nature of most anticorrosive systems. Also discussed are the characteristics of certain paint binders and how mechanical properties will differ for various environments. Corrosion of a substrate by acidic breakdown products of some paints is mentioned in conjunction with a discussion on convenience versus ultimate performance. A brief mention is made of the three main components of a paint system, and the principal types of paint are placed in broad categories, with the main strength and weaknesses of each type listed.

Jan 1, 1979

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968