Search Documents

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By John D. Campbell

Alberta Plains coals exhibit an almost rectilinear system of vertical fracturing called "cleat", which is best traced by mapping true bearings of underground coal mine rooms. The cleat pattern is approximately conformable with a pattern of surficial features and a pattern of bedrock jointing in the Alberta Plains, and with the trend of the Rocky Mountain Trench, but not with the distribution pattern of coal rank nor with the trend of the eastern boundary of the Rocky Mountains and Foothills physiographic province. The processes resulting in cleat remain in doubt, but cleat is always of practical importance in extracting coal from deeply buried deposits.

Jan 1, 1979

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By J. C. Ingram

IT SEEMS particularly appropriate that, in celebrating its Diamond Anniversary, the Canadian Institute of Mining and Metalturgy chose our Province of British Columbia as its locale in this, our own Centennial year. I am sure your organization is justifiably proud of its achievements and growth over the period of its sixty years, and we, for our part, are justifiably proud of our growth over our first one hundred years. With your kind indulgence I pro-pose to talk to you today about our industrial growth, or, to put it an-other way, to highlight, historically, our progress in industrial development over the past one hundred years, and to take the liberty of speculating on what we may reasonably look forward to over the next few years. I am sure, Mr. Chairman, that some may have questioned the appropriateness of a talk on the industrial development of British Columbia to the Canadian Institute of Mining and Metallurgy. However, strangely enough, we in British Columbia owe our origin, constitution-ally and industrially, to the mining industry.

Jan 1, 1958

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By P. K. Kaiser, S. M. Maloney, S. P. Singh

"Corrosion of underground support measures constitutes a concern to industry in both safety and economic terms. It also represents a potential market for corrosion resistant materials such as stainless steel.In order to assess the market potential for a stainless steel friction rock bolt, a review of current corrosion processes and remedial or preventative measures in the underground environment was undertaken. This was supplemented by distribution to industry of a detailed questionnaire, concerning the magnitude and extent of support corrosion and the costs of current support measures, and by visits to selected sites. Following data synthesis, support costs were established and the economic benefit of stainless steel rock bolts evaluated.Stainless steel rock bolts can be an effective cost reducing measure in unscreened areas requiring frequent reconditioning. Their benefit is rapidly diminished, however, if only partial reconditioning is required, the reconditioning interval is long or if screening is required.While most industry personnel are receptive to the application of stainless steel support measures, the localization of corrosion problems and the potential high cost of this type of support are barriers to its widespread implementation. They have potential for use in extreme environments. However, this relatively small market may not be economically viable.IntroductionFriction rock bolts are the simplest of all interior rock fixtures. The friction resistance to sliding of the rock on the bolt is generated by a radial pressure against the borehole wall over the length of the bolt. Two types of friction rock bolts are currently marketed, the Split Set and the Swellex.Unlike conventional point anchor bolts, friction rock stabilizers may move relative to the rock strata and maintain their capacity even if rock shifts, a condition that sometimes loosens or breaks conventional bolts. Ease of installation, effectiveness in jointed as well as weaker rock, and the possibility of having relatively long bolts are a few of the many advantages which generate considerable interest in the application of friction rock bolts (Wijk and Skogberg, 1982). However, due to their thin-walled construction and large surface area, frictional rock stabilizers are more susceptible than conventional bolts to damage by corrosion. For this reason, they are normally not recommended for long-term use (Jolly and Neumeier, 1987).In light of the above discussion; the Nickel Development Institute commissioned a study by the Geomechanics Research Centre with the objective of generating a credible database for the assessment of the feasibility of a stainless steel friction bolt system in corrosive ground and mine environments."

Jan 1, 1990

By W. Noel O?Brien

Introduction Since 1930 numerous improvements have been made in equipment designed for the mechanical removal of broken ore in underground mining operations. New applications of mechanical equipment, as? well as improvements and adaptations of well established systems, are being made continually. It is the purpose of this paper to discuss present-day equipment for the removal or transfer of broken ore by means of a powered hoist and scraper arrangement. The terms used throughout the paper are those commonly employed in the trade literature and by mining men. The terms slusher hoist, hoist, and scraper hoist are used inter-changeably to mean a machine, powered by compressed air or electricity, with drums for the winding of wire rope. The tail rope, also known as the pull-back rope or return rope, drags the empty scraper toward the tail-sheave, that is, back to the loading point. No attempt is made to cover the entire field of application of scraping methods. Rather it is the? writer's desire to emphasize the fundamental principles of scraping practice and design and to relate them to some modern applications. The available literature on scraping practice has been freely used. together with personal observation and information and advice of practising engineers and representatives of companies manufacturing slushing equipment.

Jan 1, 1951

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

By Hermann A. Derbuch

Twin Mining made a conscious decision when it changed from gold mine explorer and developer to become a diamond explorer in Canada?s Arctic. It was a decision of survival in an environment that saw junior gold companies either disappear or turn into dot com companies. Twin Mining learned fast and staked within weeks of that decision the first 50 sq. km of claims on, what became, its TORNGAT property at 59½° latitude on the east coast of the Ungava Bay in northern Quebec. This land position, 724 diamonds later (including 322 macro diamonds of gem quality, white and transparent) grew to 507 sq. km today. The 74° latitude called when Twin Mining exercised the option to acquire 3 claims owned by Helix Resources Inc. which revealed exceptional diamond potential. A gem quality 5.4 mm (0.768 carat white and transparent) diamond and the discovery of 16 pipes on 15.2 ha convinced Twin Mining?s board to sanction the deal. Both properties have outstanding features. Kimberlite Dykes and Pipes are in outcrop. The property locations have deep-sea access near existing infrastructure. Their locations are in an environment that is stable and development friendly and has a positive track record with successfully operating mines near-by.

May 1, 2001

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

By P. D. S. St. Pierre

IN REGENT YEARS, blast furnace operators have found it necessary to improve their technology in order to handle increasingly low-grade feed and yet satisfy the demands for greater tonnages of metal. Studies have been made covering several aspects of the problem, and in this connection the slags produced in the iron-making process have been critically examined with a view to discovering the slag with the optimum properties for a given operation. A good slag should combine, as far as possible, the properties listed in Table I. Unfortunately, some of these desirable properties are incompatible. For example, the advantage of the small ?bulk of a low-flux slag is offset by its low desulphurization potential and high viscosity. Similarly, a very fluid slag increases refractory wear. It will be seen, then, that a balance must he struck between these conflicting requirements. In the .present paper only the melting relationships of blast furnace slag ?compositions will be considered in detail. In interpreting the data herein presented, the optimum property requirements listed in Table 1 must strictly be borne in mind. It should also be noted that the discussion presented here always relates to calcined fluxes, since this facilitates reference to the final slag composition. Thus, in making calculations pertaining to the ?burdening of the furnace, due allowance should ?be made for the fact that the fluxes are added as carbonates.

Jan 1, 1956

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By I. Vazaios, M. S. Diederichs, N. Vlachopoulos

"As rock engineering moves from continuum to more discontinuum approaches for modeling, the engineer must make decisions regarding the degree of complexity to simulate for a given application, balancing the level of structural detail within the rockmass model with computational cost and result accuracy. It is important to consider that model does not need to include all the existent fractures and that representative geometrical properties for a given rock mass volume can be defined including only major structural entities.Within this paper, the scale-dependency associated with the geometrical properties of fractured rock is investigated utilizing a Synthetic Rockmass (SRM) approach with a view to characterize such ground to aid in the design of geotechnical works. In terms of process, the concept of the Representative Elementary Volume (REV) is used to determine the equivalent structural properties of the rockmass in order to justify the applicability of far-field behaviour of such ground. A large size Discrete Fracture Network (DFN) measuring 60m x 60m x 60m has been generated using the structural data obtained from LiDAR scanning of the Brockville Tunnel, Ontario, Canada. A number of DFN samples of varying sizes are extracted from the master network, generated using MoFrac, in order to be used as a the basis of the structural analysis of the rockmass. Volumetric measurements for the density and the intensity of jointing are employed in order to approximate the geometrical REV for the networks.In this paper a complete methodology of how to generate a DFN from LiDAR data and its analysis in order to determine the size of a geometrical REV is demonstrated. For the specific rockmass found in the area of the Brockville Tunnel, a geometrical REV measuring 3.5m x 3.5m x 7m is established. The results are generally in good agreement with the in-situ observations."

Jan 1, 2015

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By A. A. Brant

ONE of the reasons advanced for the decline in prospecting and discovery is that, as regards surficial examination, the law of diminishing returns is becoming applicable. Fewer surficially unprospected fields remain; therefore, fewer discoveries by such means result. Much in the nature of mineral resources remains to be unearthed, but even now, and more so in the future, will discovery depend on painstaking petrographic and structural mapping, aided, where necessary, by judicious applications of all the complementary scientific knowledge and devices (e.g., thin section microscopy, geophysics, and drilling) that experience proves effective in localizing a mineral deposit even beneath drift, lake, or muskeg. It is to be expected, then, that the rate of discovery will decrease, that the cost per discovery will greatly increase, and that the work of discovery will become more and more the careful, methodical assembling of field data, conscientiously interpreted on the basis of scientific knowledge by trained, experienced operatives. In view of these trends, the status of applied geophysics to Canadian mining exploration and development work might well be reviewed. The niche which geophysics may occupy relative to geological surveying and drilling has been clarified by the last twenty years' experience. The cloud of somewhat justifiable scepticism that followed the 'geophysical promotion' period of the late 1920's has lifted. Mining, exploration, and finance companies, in open-minded fashion, are seeking sound advice as to what are the scope and limitations of the geophysical methods at present practised. The purpose of this paper and the following one is, therefore, as far as lies within the author's power, to review briefly the geophysical methods at present in practice in Canada, and, at greater length, to joint out impartially and critically their scope, merits, shortcomings, an possible future development. The treatment will be non-technical, the hope being that an accurate statement of the present status of geophysics in Canada may do much to result in a sounder, saner growth of what, in the future, shall undoubted} y prove an increasingly useful tool in exploration and development work. ?

Jan 1, 1942