Search Documents

By Olli Haavisto, Lauri Koresaar, Navid Khajehzadeh

In recent times sustainable minerals processing is an important topic in research. Sustainable mining is linked with efficient use of energy and human resource in all process stages including beneficiation of the ore. Controlling and optimizing the recovery while preserving the grade of the concentrate is extremely important in flotation plants. This development requires new technological solutions and has given rise to the multitude of application areas for lasers. X-ray Fluorescence (XRF) and Laser-Induced Breakdown Spectroscopy (LIBS) are currently two of the predominant non-contact and direct analysing methods in industry. LIBS and XRF measurement techniques both have high capabilities for measuring elements. LIBS has a very simple and easy-to-implement spectroscopic setup, wider range of elements can be detected with online LIBS and measuring light elements is simpler by LIBS compared with XRF. It is of great interest to extract mineralogical information from the elemental results with no modification on the measurement setup. In order to achieve this, more advanced interpretation of the elemental peaks of LIBS spectra is required. Therefore, the major focus of this research is about measuring mineral concentrations from the elemental lines of LIBS spectra using advanced statistical methods. This accomplishment provides knowledge about mineral concentrations from the real-time assay data of the slurry LIBS analyzer. Consequently, this paper first discusses an analytical method called partial least squares regression leading to rapid mineral identification from the elemental contents of the LIBS technique. Then the technique is employed to analyze the mineral contents quantitatively through the information acquired from an on-stream LIBS slurry analyser. This can lead to many benefits such as rapid control of concentrate quality, enhanced recovery, saving time, energy and manpower.

Jan 1, 2016

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By Frank Mucciardi, Zhongsen Yuan

A new heat transfer technology --- termed Thermopump technology has been developed. This technology originates from conventional heat pipe configurations but has now evolved into its own class of heat transfer units, which we refer to as `Thermopumps (TP)'. A key feature is that Thermopump technology can be applied to high temperature / high heat flux environments where conventional heat pipe technology fails. Moreover, when implemented in less demanding applications where heat pipes appear to operate, Thermopump units have been found to function more smoothly and reliably. This paper will introduce Thermopump technology and several applications of this technology in steelmaking and refining will also be discussed. In addition, this paper will focus on three classes of applications: 1) waterless, non-consumable, high efficiency Thermopump oxygen lance and/or burner for EAF's, 2) Thermopump ladle lance for the desulfurization process, and 3) Thermopump cooling panels for furnace walls and roofs. Facilities equipped with Thermopump technology are expected to he better than the current corresponding ones in terms of increasing productivity and energy efficiency while at the same time lowering operating costs.

Jan 1, 2004

By Harold Hopkins

THE Wright-Hargreaves mine is one of a group of seven mines long active in the Kirkland Lake district, Ontario. Detailed geological reports and maps covering the area have been published by the Ontario Department of Mines (1,3)t. Though all these mines work several productive veins there is one vein which is common to all and is known as the North Vein of the camp?not that it is the most northerly vein mined, but it is the more northerly of the two major veins of the camp. At the Wright-Hargreaves mine there are in all ten important producing veins, and most of them have a N.60°-65°E. strike and in general a steep southerly dip. It is a common belief that most of these veins lie along faults but it will be shown that whilst this is true of some of them it is not true of all, and also that a vein may lie in a fault along part of its course and elsewhere fill a fracture in line with the fault, this being a consequence of rotational movements that took place during faulting. The paper describes the history of faulting at this mine in particular, makes observations on the principal pre-ore fault, and describes the method used in solving the movements on the post-ore faults. Other details of geology are not discussed except to mention here that our main veins lie almost entirely in the syenite porphyry stock except on lower levels close to the east boundary of the property, where the North vein leaves the porphyry to enter the greywacke.

Jan 1, 1940

By R. Edinger

Aerospace and space products depend, probably more than any other products in industry, on advanced materials. While there are many ways of producing aerospace parts, in many cases the process does not allow the design of the metallurgical properties according to the part or product requirements in accordance with its mechanical configuration. Key to the next level of innovative manufacturing is the capability to control the amount of energy applied to the process, as well as the addition of materials in form of vapor or solid particles such as powder in order to build up the metallurgical composition required. With the development of a high speed pulsed laser-electron beam source, the LASTRON(TM) technology, we deliver the basic requirement for a digital manufacturing process of aerospace and space products. This technology, combining Laser and electron beam, finds application in welding, drilling-machining, and is currently modified to allow digital coating (PEB-PVD) methods. In addition to the coating, a powder metallurgical process, called Rapid Manufacturing (RM), will allow the precision melting of parts based on CAD/CAM files. The RM process and the digital coating will allow the production of graded aerospace alloys in parts for jet engines and aero-structures.

Jan 1, 2006

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By G. Ellie, D. F. Coates

"The mining of coal in thick and inclined seams is difficult, and there are only a few countries in the world that are really interested in the problems associated with their exploitation. In France a considerable amount of investment has been made in the mechanization of systems appropriate for such conditions.For seams inclined up to 50 degrees, of normal thickness, a new system was introduced in 1967. It consists of a longwall advancing to the rise with walking props, a shearer and hydraulic backfill. During the first two years the panel productivity was an average of 25 TN/MS, and they foresee the possibility of reaching an average of 30 TN/MS.A system for thick beds, both horizontal and inclined, is in p•rocess of being mechanized. In 1969 they started with a method consisting of a longwall in a footwall slice, or sub-level drifts with walking props, and caving and drawing up to a height of 20 m of coal. Recent experiments with a shearer have produced panel productivities between 9 and 11 TN /MS, and there is hope that with experience an average of 16 TN/MS will be obtained.In 1964 a method was initiated for beds inclined from 60 to 90 degrees, based on a mechanical cutter designed by the collieries in Lorraine. An overhand slice of 4.2 m in height is taken with a drum cutter mounted on the end of a boom. Hydraulic fill is placed at the completion of a slice. The face productivity, which has been from 13-20 TN /MS, can be perhaps increased to an average of 22 TN/MS. For those companies with important reserves in inclined and thick seams, these French systems may be worth the trouble of examining in some detail."

Jan 1, 1972

By A. Rodriguez-Prado, P. Kuschk, R. L. Legge, W. C. Lennox

Using constructed wetlands to chemically reduce hexavalent chromium Cr(VI) to Cr(III) from industrial and mining wastewater has proven to be feasible and efficient. Applying first-order kinetics to describe the process is simple, but in some cases a more accurate model is required to reflect the process. This paper studies the feasibility of using non–first-order kinetics to describe the reduction process. Results indicate that half- and second-order kinetics adequately described Cr(VI) reduction in laboratory wetland mesocosms. The organic carbon content played a relevant role, whether it was built up by plant growth or spiked into the feed water.

Jan 1, 2014

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By Bradley Stoughton

It is very easy to reduce iron ore at a temperature well below its melting point and produce a more-or-less-pure metal which can be used directly for implements, tools, or machines. This simplicity has been the cause of much money loss by persons who were so satisfied with the successful operation of a process that they paid all too little attention to the commercial aspects of it. How easy a direct process is may be gleaned from the fact that it was practised with some -success by primitive man, and has been in almost continuous operation in one form or another for a period of probably 4,000 years. The production of steel in ton lots, beginning about 1860, brought a new phase into the economic situation, which, however, had been already greatly modified in 1784 by Henry Cort's invention of purifying pig iron. Direct processes survived both of these revolutions, under special geographical conditions, even up to the last few years of the nineteenth century, but ceased to have any general use as the basis of supply for structural, machine, or tool industries even in countries which could have manufactured iron by a direct process, but, instead, imported the product of established iron and steel processes. And this is still the situation today, notwithstanding the invention of an incredible number of 'new' processes since 1900, most of which are abandoned, and only survived as along as their financial backers were willing and able to Jose money. Probably none of these processes failed to work pretty well, and all seemed to show a handsome profit on paper.

Jan 1, 1930

By J. W. Craig

THERE are, broadly speaking, three classes of refractories: acid, basic, and neutral. Fireclay, diaspore, silica, and the sillimanite group of minerals are included in the acid class, which for the most part are not very resistant to basic slags. The neutra! class includes chrome, graphite, and silicon carbide, while most important in the basic class are magnesite and dolomite. Although chrome is a neutral refractory, it has no sharp distinction from magnesitic refractoriness. The two are mineralogically (1) and chemically related, and there is available on the market a complete range of brick from straight chrome to straight magnesite. In many indus trial applications, one. type may be replaced by another. The present paper is confined entirely to such refractories. The following types of basic and neutra! brick, each sold under sorne special trade name, are available for use in Canada: (1) Burned chrome from crude ores (2) Burned chrome from treated ores (3) Chemically bonded (unburned) chrome-magnesite ( 4) Burned chrome-magnesite (5) Chemically bonded ( unburned) magnesite-chrome (6) Chemically bonded (unburned) high-iron magnesite (7) Burned high-iron magnesite (Regular) (8) Burned low-iron magnesite (9) Burned olivine-magnesite (10) Burned magnesitic dolomite-chrome (Magnecon) (11) Chemically bonded magnesitic dolomite-chrome (Magmecom) (12) Dolomitic brick

Jan 1, 1936

By Peter A. Hacquebard

"The coals of the Sydney and Pictou coalfields are generally classed as high volatile ""A "" and medium volatile bituminous coals but there are significant differences within and even beyond this rank. These are related to the observation that the coalification in eastern Canada is essentially post-deformational, resulting in a general increase of rank with depth in individual seams.Exploration drilling in the Sydney coalfield has shown that the rank increases offshore to M. V. bituminous at mineable depths and in the Pictou field to L. V. bituminous coal. There is also a marked easterly shift in rank within one seam at the same depth at Sydney, with the result that M. V. coal will be reached sooner in the Donkin Reserve area (at 700 m depth) than in the Lingan-No , 26 Reserve area (at 900 m depth). These rank changes are important for the manufacturing of metallurgical coke as shown with coke stability predictions based on petrographic analyses. The L. V. coal of the Pictou field can be used for blending purposes and is the only known L. V. deposit of mineable thickness in eastern Canada.In addition, the vertical rank changes between seams have been studied in ten boreholes. They are not constant within the confines of the Sydney coalfield. Four separate areas can be recognized, each with different coalification gradients, which can be related to changes in the paleogeothermal gradients . Variations of 2.5 degrees to 6. 7 degrees CI IOO m are indicated and geological causes for these changes are suggested.IntroductionThe Sydney coalfield is the largest and most important field in eastern Can ad a, and although it has been in production some 200 years, the remaining ""demonstrated "" resources of 1.6 billion metric tons can extend its production capability for at least another 100 years. All coals mined are high volatile "" A"" bituminous and have been used for both thermal and metallurgical purposes. For the latter rank variations even of a minor scale are of critical importance for the manufacturing of metallurgical coke.The significance at the present time of the Pictou coalfield, which has only modest remaining "" demonstrated"" resources of 60 million metric ton s, lies in the discovery in 1975 of a 14-million-ton deposit of low volatile bituminous coal. It is the only known low-volatile coal in eastern Canada and is suitable for use as a blend for metallurgical coal. As such, it could supply the Sydney coke ovens for a period of 30 years at the current rate o f coke production and replace imported American low volatile coal.Consequently, coal rank studies of the Sydney and Pictou fields are important not only from a geological point of view, but also because of economic considerations."

Jan 1, 1984

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, W. L. Mason, John J. Justen

"A miscible displacement pilot, using a slug of LPG driven by separator gas, was conducted in the Cardium Reservoir of the Pembina Field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gas phase, an .experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to cakulate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones, and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in con-trolling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir."

Jan 1, 1960