Search Documents

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By John D. Galloway

Mining is one of the important primary industries of Canada, with a gross production in 1927 estimated at $241,773,000- the highest in the history of the country-and an impressive dividend record. It is quite apparent, therefore, that mining is a business worthy of the careful attention of the people of Canada. Furthermore, with a vast undeveloped territory more or less mineralized, it is highly probable that our mining industry will continue to expand indefinitely, with a consequent increase in production and in the amounts of the yearly profits distributed. In recent years, the public has taken a larger interest than formerly in mining-an interest, moreover, that is not academic, but primarily from the viewpoint of profits. It is quite evident that mining is a profitable business, at least to some, and the average man on the street, hearing of these profits, is attracted thereto. I have no doubt that many of you have .read in promotion prospectuses, with figures to prove it, that mining is the most conservative, the safest, and the highest-yielding business in the world. Now, a lot of this information is best judged by the old saying that "While figures don't lie, liars figure". At the same time, mining, properly conducted, is a profitable business, even though speculative, and undoubtedly much profit will come from Canadian mines in the future. In this paper my conclusions regarding mining investments are based largely on British Columbia experience, together with some slight knowledge of mining conditions in the other Provinces. It is considered, however, that the inferences drawn are applicable to mining throughout Canada.

Jan 1, 1928

By W. J. Wright

Summary This paper describes the general situation of the mining industry in New Brunswick, and gives a detailed description of the recent developments in the antimony deposits at Lake George and the copper deposits in the vicinity of New Horton. At the end are lists of the most interesting geological literature relating to the Province and of the geological and topographic maps that have been published. Introduction In presenting this paper to the Institute, I apologize for the small amount of scientific data which it contains. Recent investigations in the Province of New Brunswick have been carried on largely by outside interests, and at present we ourselves are in the position .of taking stock. However, I am glad of the opportunity of giving you a general idea of the situation. The Province is making an honest effort to learn the truth concerning her mineral deposits and in time hopes to collect data which should be of interest to the mining community.

Jan 1, 1931

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

By P. H. Agson Gani, T. Sitorus, N. P. Widodo

"PT ANTAM UBPE Pongkor underground mine use blasting to develop its tunnels which will cause poisonous and dangerous gases trapped inside mine. To analyze this case, a study of mine ventilation, the dispersion of carbon monoxide (CO) gas concentration and diffusion coefficient is commenced. At the end, the re-entry time formula will be determined. Results indicate that this study is site specific and could only be applied in the place this study executed. The aim of this study is to be further developed by applying Principal Component Analysis (PCA) to find a universal re-entry formula. KEYWORDS Mine Ventilation, Re-Entry, Smoke Clearing, Diffusion Coefficient, Carbon Monoxide Gas, Gas Dispersion INTRODUCTION Pongkor underground mine is using cut and fill as its mining method. Thus, its development and production processes require blasting to develop its tunnel. This process caused poisonous and dangerous gases spread and trapped inside the mine, one of them is carbon monoxide (CO) gas. CO is formed in an unbalanced reaction of explosives detonation and could be the cause of headache, blackout and death to people who inhale CO at certain concentration (McPherson, 2011; Hartman, Mutmansky, Ramani, & Wang, 2012). Mine ventilation system is installed in the mine to resolve this problem. Mine ventilation play an important role to disperse CO gas by absorb the poisonous/dangerous gases and deliver clean air into mine. The important parameter is diffusion coefficient, because diffusion is affecting particulates or gasses spreading from its sources throughout the mine. Diffusion coefficient is the total diffusion in axial direction of turbulent flow mainly by convection of bulk motion, advection and eddy diffusion, while the effect of molecular diffusion is appreciably negligible (Widiatmojo et al, 2015). Taylor (1953, 1954) develops a theory about the dispersion by inducing a slow stream of solvent into a capillary tube. Taylor used Reynolds assumption of radial diffusivity to be analogous with the transfer of the matter in turbulent flow as well as the transfer of momentum and heat. Then, Taylor proposed the formula of diffusion coefficient, D (m2/s), against pipe diameter and turbulent shear velocity are as follow:"

Jan 1, 2019

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

"In 2000 the CIM Council approved the CIM Standards on Mineral Resources and Reserves – Definitions and Guidelines, developed by the CIM Standing Committee on Reserve Definitions. The Definition Standards established definitions and guidelines for the reporting of exploration information, mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reserve definitions are incorporated, by reference, in National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in Canada in February 2001 and was amended in December 2005.CIM DEFINITION STANDARDS- For Mineral Resources and Mineral ReservesPrepared by the CIM Standing Committee on Reserve DefinitionsAdopted by CIM Council on December 11, 2005FOREWORDCIM Council, on August 20, 2000, approved the ""CIM Standards on Mineral Resources andReserves - Definitions and Guidelines,"" developed by the CIM Standing Committee on ReserveDefinitions. The CIM Definition Standards on Mineral Resources and Reserves (CIM DefinitionStandards) establish definitions and guidelines for the reporting of exploration information,mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reservedefinitions were incorporated, by reference, in National Instrument 43-101 - Standards ofDisclosure for Mineral Projects (NI 43-101), which became effective February 1, 2001.At the August 20, 2000 Council meeting a new CIM Standing Committee on ReserveDefinitions was established consisting of the following: John Postle, Bernie Haystead, LarryCochrane, Normand Champigny, Mike Hoffman, Colin McKenny, Jack Mullins, Phil Olson,Fred Payne, Jody Todd and Joe Ringwald.Subsequent to the publishing of the August 20, 2000 CIM Standards on Mineral Resourcesand Reserves, various CIM committees have compiled and published more extensivedocumentation on mining industry standard practices for estimating Mineral Resources andMineral Reserves. These standard practices provide more detailed guidance than that containedin the August 20, 2000 CIM Standards on Mineral Resources and Reserves. On November 14,2004 CIM Council adopted an update to the CIM Definition Standards to reflect the moredetailed guidance available and effect certain editorial changes required to maintain consistencywith current regulations. This version of the CIM Definition Standards includes further editorialchanges required to maintain compatibility with the new version of National Instrument 43-101which is expected to become law at the end of 2005. The CIM Definition Standards can beviewed on the CIM website at www.cim.org."

Jan 1, 2003

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By J. N. Brooke

"This paper deals with the training of the mining and mineral engineer and the role that these professional people must play in their company environment, particularly in relation to management.THERE IS SOME CONCERN in the mining industry that the numbers of engineering graduates attracted to it and the academic training that these people have received is inappropriate. Evidence for this is:1. -The meetings and studies initiated by the various mining engineering societies to discuss:(a) attracting students and graduates to the industry; and (b) the appropriateness of the present academic training for the needs of the industry."

Jan 1, 1968

As a bubble travels through the pulp region of a flotation cell, it will collect the most hydrophobic particles of an intermediate particle size range, this being the primary source of true flotation selectivity. Despite its role on bubble-particle attachment, however, particle hydrophobicity is still missing a mathematical definition that can be used for plant simulation. In this paper, particle hydrophobicity is defined in terms of the induction time necessary for attachment and then linked to the mass of collector adsorbed per particle. This allows particle hydrophobicity to be written as a function of density of collector adsorption as well as particle size and mineralogy. The model is calibrated from the experimental measurement of the flotation rate constant. Liberation data from an industrial flotation rougher is used for model validation. It is demonstrated that the model can describe a broad experimental dataset by means of a minimal number of parameters. Main industrial application is in simulating the effect of the chemical environment upon plant metallurgical performance.

Jan 1, 2006

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man's varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930's when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years' duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry's basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada's historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country's major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

By G. C. Bateman

Canada is a very large country with a small population which is growing very slowly. We have great natural resources, but with our limited population we are continually looking afield for new capital to develop these resources. Our mining areas are among the most important fields offering opportunities for new capital and because of the wide-spread appeal which mining makes this industry commands a great deal of attention. While we are glad to see new capital from any source, we welcome it particularly from Great Britain, for, although we offer equal opportunities to the nationals of any country we would be glad to see the development of our natural resources financed as far as possible within the Empire. However, when we invite ne capital we must accept certain responsibilities, and while we have opportunities to offer, we should ask ourselves how these opportunities are taken advantage of and what sort of treatment the foreign investor receives.

Jan 1, 1925

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978