Search Documents

By Derek V. Ellis

Coastal and marine mines affect the seabed?s biological resources, eg fisheries, when large volume wastes such as tailings are placed on the seabed, and by the extraction processes from marine mining. Worldwide monitoring of such effects for the past 30+ years now provides information to describe Best Practice design, construction and monitoring procedures. The critical environmental factors for submarine tailings placement (STP) are the selection of an appropriate deposition site and discharge depth, the deposition rate of the tailings, and the speed of biodiversity recovery to a sustainable ecological succession. These should be predictable at new sites using current modeling and experimental procedures. Prediction procedures are still needed to minimize potential destabilization of deposited tailings, and consequent biodiversity recovery setbacks. Comparable environmental information is needed from marine mining sites.

May 1, 2002

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By Jacque Trottier, Marcel Vallée, Gratien Gélinas

"Mineral exploration in Canada traditionally has gone from boom to bust in cyclical pat-terns following market and discovery cycles, but other endemic factors related to exploration financing and performance have contributed to the amplitude and recurrence of these fluctuations. In view of these problems, junior exploration is reviewed here in a marketing perspective, looking at the 4 Ps: Product, Price, Placement and Promotion.In the 1980s, MEDA incentives gave the shares of junior and mining companies significant price and promotion advantages, and contributed to excessive exploration funding. Many were thus led to minimize the basic values needed for continued investor interest: appropriate levels of product quality, sustained share value and customer satisfaction. Basic changes are needed to improve the marketing of junior mineral exploration in the future, with or without improved fiscal incentives. To be successful, the required improvements must come from the technical participants, but the financial partners also need to be involved.Exploration in Canada must be marketed with vigour, both in Canada and internationally. Exploration, mine development and mine production are essential to our economy. They are environmentally acceptable and they are welcome in Quebec and in most Canadian provinces and territories. Canadian exploration and mining are entrepreneurial industries that must take better advantage of their strengths and achievements and remove the shortcomings that hinder them: nobody can do it for them!"

Jan 1, 1996

By Sanjeeva Latchireddi

"Deteriorating ore grade and high demand of metals has tremendously influenced the unit capacity of SAG mills. Pebble circuits have been added to the existing SAG circuits to increase their unit capacity. To make the pebble circuits justifiable, the grate openings are increased almost to 4.5 inches to draw large quantity of pebbles. The inherent transportation problems associated with SAG mills in closed circuit with pebble fraction are more complicated than the single stage SAG mill operation, because the coarse pebbles behave significantly different to that of slurry in pulp lifters. In addition, operation of mills at higher speed, to take advantage of precise design of high release angled shell lifters significantly reduces the discharge efficiency of the conventional pulp dischargers. The presence of a sizable quantity of pebbles in the pulp lifter limits the space available and reduces the flow gradient through the grate thus increases the load inside the mill and hence the mill power-draw. This paper analyses all the problems associated in discharge of slurry and pebbles in SAG mills with pebble circuits. The Outokumpu patented Turbo Pulp Lifter (TPLTM) aims at eliminating the inherent material transport problems to ensure good grinding conditions. Recent installation of TPLTM in a 26-ft SAG mill has proven these claims by reducing the specific power consumption while increasing the mill capacity.INTRODUCTIONThe conventional wisdom is to look at the semi-autogenous grinding (SAG) mill as just another grinding mill in which ball charge, mill filling, and mill speed are varied to attain maximum throughput. Liner design for the SAG was also approached more from a wear perspective rather than a metallurgical and hydraulic-flow perspective. The extensive research work carried out by Latchireddi and Morrell (1997,2003a and 2003b) has demonstrated to think of the SAG as more of a pump in which the grates and pulp discharger end (“impeller”) were designed to efficiently discharge the product sized particles smaller than the grate size with minimal recirculation out of the mill.The rock load in the mill is essentially depends on ore characteristics and the discharge rate of broken particles. The discharge rate of the product material depends on how efficiently the discharge pump (grate and pulp lifters) is operating. Similar to the impeller design affecting the pump capacity, the pulp lifter design affects the discharge capacity (or mill throughput) of the SAG/AG grinding mills. The general arrangement of AG/SAG mills discharge system is shown in Figure 1."

Jan 1, 2007

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By P. West-Sells, B. Wassink, N. Fisher

Gold leaching from a commercial cyanide-amenable gold ore was studied at 25°C using sodium bisulfide-hydrogen sulfide solutions containing elemental sulfur. Gold extraction from the ore using 0.55 M NaSH, 4.1 atm (60 PSI) H2S, 1 g/L S8 and 26% solids by weight was about as good as the best extraction obtained by cyanidation. Maximum extraction was achieved in roughly 48 hours. Sulfur dissolves in the bisulfide solutions to form a mixture of polysulfides. Simple speciation calculations indicate that gold solubility as bisulfide complexes should be roughly ten times higher than in the absence of added zerovalent sulfur. The principal bisulfide complex is believed to be [Au(HS)2]-. Gold dissolution is favoured by increasing HS- concentration and by increasing H25 pressure. Polysulfide complexes of gold are also likely to be formed, and may contribute substantially to gold leaching. Two experiments using pure gold were also performed. Up to 100 mg/L gold was dissolved in 140 hours using 0.55 M NaSH, 1 g/L added elemental sulfur and 6.2 atm H2S.

Jan 1, 2005

By Ralf M. Kleine

THE property of Consolidated 1 Discovery Yellowknife Mines Limited, (Figure I) is situated in the Northwest Territories, approximately 50 air miles north of the town of Yellowknife. The mine is reached by a shaft which extends from surface to a depth of 4,000 feet, with working levels established at 1 50-foot intervals. Stopping operations are carried on throughout a vertical range of 2,000 feet, with both shrinkage and cut and fill methods being used, depending on the ground conditions. Production started in 1950 and milling is done in a 1 65-ton per day cyanide plant. During ten months of the year, the property is serviced entirely by air, utilizing charter aircraft from Yellowknife. A 4,000-foot runway near the mine was constructed from mill tailings. This strip is adequate to receive Bristol freighter planes carrying heavy loads. Other servicing is done by Otter aircraft, equipped with skis or wheels for winter and with pontoons for summer operations.

Jan 1, 1962

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By J. D. Christian

WHEN mining development began in the Kirkland Lake camp, twenty-five years ago, there was very little information obtainable from surface showings as to the nature of the ore deposits. A length of almost a mile of the main 'break' lay under the south arm of the lake, and elsewhere most of the outcrops were covered with glacial drift. Shafts were sunk on ore-bodies of uncertain value, either on the outcrop of the veins or-because of the lake to the north-in the south or hanging-wall. In the second year of the camp's development, the Great War broke out and retarded progress for its duration. He would have been a real optimist who, in those early years, could have foreseen mining at depths of more than a mile.

Jan 1, 1939

By Clifford S. Gibson

THE Workmen's Compensation Ace defines Silicosis as "a fibrocic condition of the lungs caused by the inhalation of silica dust sufficient co produce a lessened capacity for work". This fibrocic condition muse exhibit a specific appearance in the X-ray picture of the chest-an appearance which is not characteristic of several lung conditions which can cause lessened capacity for work and which are not due co silicosis. The layman is sufficiently familiar with this subject co know chat, as far as our knowledge goes, quartz is one of the principal objectionable factors in the production of this condition. He should also know that silicosis respects neither geographical nor industrial boundaries. It is as much a factor in some industrial processes (e.g. foundry work, sandblasting) as it is in mines handling ores containing quartz. Its development co a recognizable stage is usually a matter of many years. As yet, its cure is unknown. Its prevention is possible in varying degrees. The layman should also know that the development of fibrosis may be accelerated by breathing in, or living in, any atmosphere containing dust. Few normal adults, particularly those above a certain age, have clear lungs, and fibrosis in varying degrees is noted in the farmer, the steel worker, the clerk, and many others in varied occupations. It is not restricted to miners. Medical and industrial journals, and at times the press, are crammed with data pertaining to this subject, much of which is misinformation. This is particularly true of certain !laces where the preventive and compensation measures for the good o those earning their livelihood in an industry in which silicosis may be contracted are not so far advanced as in our own Province. A great many of these publishings are alarming to the layman. They leave him with the impression that he is taking his life in his hands if he elects to work underground, particularly in a gold mine-that he has at once sold his heritage of health and chat sooner or later he will succumb to the ravages of this ailment. Nothing could be farther from the truth. Actually, under present conditions in Ontario mines, a very small percentage of the men employed ever become impaired by silicosis to the extent chat they must withdraw from the industry. I propose to tell you briefly something of this subject as it affects our mines.

Jan 1, 1937

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By Robert B. Parsons

"A t last the legal red tape which has tied up flow-through share financing has been cut. New rules effective for deals signed after 1986 simplify flow-through financing by removing the necessity f or cumbersome agency relationships. But there is no free lunch-the new rules require increased government reporting. And beware federal tax reform promises to have a good look at the new flow-through share rules. IntroductionFlow-through shares have always worked better in theory then reality as an effective financing tool. The concept is straightforward: a transfer of risks, tax deductions, and potential returns. But the mechanics of the old flow-through rules made the transfer of risk impractical to impossible by placing the responsibility for incurring Canadian exploration expense (CEE) on investors. The new rules are significantly more realistic, shifting that responsibility to the issuing corporation. However, every silver lining must have a few clouds around it. In the case of the new flow-through rules, the more obvious negatives are increased reporting requirements and reductions in CEE eligible for flow-through by amounts of assistance received. The new rules are effective for deals signed after 1986, however, so a few old-style deals are still around. Practical Difficulties with Old RulesThe old rules which applied to investments in flow-through shares were structured so as to make it the responsibility of the investor, rather than the issuing corporation, to perform the Canadian exploration expense for flow-through. Since most investors had neither the expertise nor the inclination to incur the CEE, this requirement necessitated the use of cumbersome arrangements whereby the investors would appoint an agent (usually the issuing corporation) to incur CEE on their behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, the awkward legal structure of such an arrangement made the investor the ""principal"" incurring the CEE. As such, the requirements of the old rules were met and the investors could receive their flow-through share s."

Jan 1, 1987

By J. E. Armstrong

"IntroductionT'HE PRODUCTION of gravel and sand may be considered to be the major mining operation in the Lower Fraser Valley of British Columbia. At least thirty pits are in operation with a yearly production probably in excess of two million yards and a value in excess of one million five hundred thousand dollars before crushing, washing, and sizing. The value of the finished products would probably be double the above figure.Since 1949, the writer and his co-workers have been engaged in the geological investigation of the Lower Fraser valley and adjoining Coast mountains for the Geological Survey of Canada. The study, which is not yet completed, includes both bed-rock geology and geology of the unconsolidated sediments lying above bed-rock. In a rapidly expanding industrial area, .an advance knowledge of the geology may• greatly aid in future 'planning, and in many cases may .prevent not only the wastage of large sums of money, 'but possible disaster. Some of the present and future applications in which geological information in the Lower Fraser valley should be of value are as follows: the development of domestic, irrigation, industrial, and municipal groundwater supplies; drainage for industrial sites,, roadbeds, and farmlands; flood control along the Fraser river and smaller streams in the area; the location of dam sites, of major tunnels for water supply •and sewage, of road-beds, of foundation sites for large buildings .and other engineering undertakings in which geology may aid; the evaluation of oil and gas •possibilities; the production of building stone; and the production of sand and gravel, the subject with which this paper is primarily concerned."

Jan 1, 1953