Search Documents

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By C. Vanvoren

"Since 1975, the Aluminium Pechiney Research Centre at Saint-Jean-de-Maurienne (LRF) has been concentrating its efforts on designing, testing and perfecting the Aluminium Pechiney point-fed prebaked reduction cell.In 1979, the AP18 cell (180 kA) was industrially launched with the construction and start-up of the F line in Saint-Jean. The following generation, the AP30 (300 kA), with prototypes started in 1981, was launched in 1986 on the Saint-Jean G line. Along with cell design, efficient process control systems were developed to pilot alumina feeding and bath composition. Together, these pots are currently producing 4.6 Mt of aluminum, i.e., 18% of the world’s overall yearly production.In 1989, the research centre faced a new challenge: to push the limits for the size of a reduction cell to further improve the profitability of Greenfield projects. This new generation development was also the opportunity for a significant redesign of the Aluminium Pechiney electrolysis information system.With a track record of ten years of semiindustrial operation with three prototypes, the AP50 technology is now ready for industrial implementation and enables a significant breakthrough to be made in terms of return on investment of a Greenfield smelter."

Jan 1, 2002

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By D. Gendzwill, N. Martin

"In early 1987, the Patience Lake potash mine near Saskatoon, Saskatchewan, was closed due to uncontrollable floodingWater inflows were first encountered during routine mining in 1975 at the south boundary of the mine lease. Underground grouting and construction of bulkheads limited the flo but did not completely stop it. Subsequent seismic surveys showed that the mine had approached the edge of a large collapse structure in which the salt and potash had been partly dissolved and removed by groundwater.In 1986, the small flow into the mine started to grow. Despite renewed grouting, the flood increased and outstripped pump capacity. The grouting program temporarily slowed the inflow but was unable to stop it. Eventually, from seismic and drilling evidence, it became clear that the water source was an extensive system of vertical fractures which would be impossible to seal by drilling and grouting from underground. A new plan to install 14 bulkheads underground would have sealed the water source from the rest of the mine but the construction program could not be completed before rapidly increasing inflow threatened to fill the mine. The underground mine was closed and a new solution mine started in 1988."

Jan 1, 1996

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

A mini- or micro-machine is a small electro- mechanical device. There are several existing applications of micro-sensors such as the accelerometers used in automobile airbags or the force sensors and grippers used at the ends of micro-surgery tools. Potential applications of existing mini- and micro-technologies are possible and could be used to improve the control and efficiency of fragmentation, heap leaching and other mining and mineral processing operations. A more radical proposition is to devise mass-produced, possibly disposable, minimachines that would operate in large groups. These would be the basis of highly selective, efficient, flexible, and clean mining and mineral processing methods. The paper is intended to promote discussion of how innovative applications of mini-technologies can be used to improve and radically change current mining and mineral processing methods.

Jan 1, 2002

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

"In an environment of rising energy prices and mining at greater depths, cost-efficient loading and hauling equipment is essential. Conducted at an underground mining operation, this study analyzes the energy consumption and gas emissions of diesel and electric load-haul-dump machines (LHDs) with similar bucket capacities. Based on energy prices from the first quarter of 2014, results of discrete event simulation show that energy costs for diesel and electric LHDs are US$0.24/t and US$0.07/t, respectively. Also, diesel LHDs emit 2.68 kg CO2 per litre of diesel fuel, whereas using electric machines reduces the need for ventilation to mitigate engine heat and emissions and reduces energy costs.RÉSUMÉ Dans un contexte de croissance des prix de l’énergie et d’exploitation minière à des profondeurs de plus en plus grandes, il est essentiel d’avoir des équipements de chargement et de transport les plus rentables possible. La présente étude, effectuée dans une mine souterraine, analyse la consommation énergétique et les émissions de gaz de chargeuses-navettes (LHD) au diésel et à l’électricité ayant des capacités de godet similaires. En se basant sur les prix courants de l’énergie, les résultats d’une simulation d’événements discrets montrent que les coûts énergétiques pour les LHD au diésel et à l’électricité sont respectivement de 0,24 $US/t et de 0,07 $US/t. De plus, les LHD au diésel émettent 2,68 kg CO2 par litre de combustible diésel alors que les machines utilisant l’électricité réduisent le besoin de ventilation pour atténuer la chaleur des moteurs et les émissions en plus de réduire les coûts énergétiques."

Jan 1, 2015

By Constantin D. Pitis

Similarly to notions of constant capital/expenses in business or magnetization power for electric motors an energetic base load (E0) is always necessary to set up a mining process. Denominated as ?non-productive energy? or base load, (E0) is a constant component of the entire energy consumption of the process, while another component the ?productive energy? (Ep) is variable, being function of the production/throughput (M). By using these new concepts, the author creates an energetic model proposing a new method of assessing changes in mining processes (throughput) that can reveal possible energy savings (DSM component) or energy losses. Proposed mathematical model of assessing (E0) and energy savings by using ?Marginal Energy Usage Index? (MEUI) enables creation of historical benchmarks and direct on line energetic (efficiency) assessment of mining processes and/or equipments. The paper analyses the case of assessing possible energy savings that can be obtained by: ?? Improving efficiencies of various equipments (by retrofit) ? reducing E0 ?? Improving the process control or other process changes ? reducing Ep ?? Monitoring persistence of the adopted Energy Conservation Measures (ECMs). For the new plant design, the proposed method enables prediction of Customer Baseline in various mine/process configurations. The method could become part of a ?preventive action? in design process by offering a reliable tool of assessing additional financial effort (Incremental cost) when choosing various higher efficiency equipments and/or processes.

Oct 1, 2009

By Knud Sinding

Mining firms are widely criticised for their adverse impacts on the environment. At the same time many firms in the industry devote extensive resources, both financial and managerial, to the reduction or elimination such impacts. Very considerable improvements have been made, although these are sometimes overshadowed by a few high-profile accidents, such as the occasional collapse of a cyanide-containing tailings dam. In parallel, much effort is also directed at projecting a positive environmental image, as witnessed by extensive environmental reporting, both on paper and increasingly through web-platforms. Mining projects today almost invariably involve some form of environmental protection. In industrial countries regulations in this area are extremely stringent, as is enforcement. In less well developed countries, regulation and enforcement may be weaker, but firms are in many cases and for a number of reasons committing themselves to high levels of environmental protection, even if they might get away without doing so. Research in the area of environmental performance of mining firms has so far paid much attention to concepts such as sustainability indicators and the sustainability of individual firms. Given the still raging debates about the appropriate way to determine the degree to which any given firm is sustainable (Welford 1995) as well as the usefulness of what will in the final analysis be a value judgement, anyone on the sidelines of the debate will come back to the fundamental issue, how is knowledge that a particular firm has been judged ?sustainable? going to be made use of. This issue remains unresolved, which may explain the lack of progress in formulating a useful definition of a sustainable firm The question addressed in this paper is not so much about what firms are doing on the ground or in any particular case of environmental protection, but more in the subsequent use of these efforts - and by extension - on the overall direction of corporate environmental strategy. The fundamental problem facing all mining firms is that they cannot easily benefit from unilaterally reducing their environmental impact. The firm can of course avoid liability and keep a variety of stakeholders happy and hence experience lower costs of obtaining the [input] resources they need (in a broad sense, not just minerals), but this represents only part of the opportunities available form pursuing an environmental strategy (Reinhardt 2000). The other part, which may have an enormous potential, involves the concepts of competitor management and product differentiation. The logic of keeping stakeholders happy has been most forcefully argued by Pfeffer and Salanchick (1978) who link the behaviour of firms in all domains to their ability to obtain the resources they need, at a cost that is lower than it would otherwise be (Pfeffer & Salanccik 1978). Several varieties of strategy can be included under this heading, including cost reduction and risk management. The alternative logic is to convince customers that they want to pay more for minerals supplied by mining firm X or directly attributable to mine Y, or by making all mineral users pay more. These two strategies, which may be referred to as product differentiation and competitor management, respectively (Reinhardt 2000) are related to the demand side of mineral supply, whereas cost reduction and risk management are related to the supply side. Mining firms have not pursued the demand side very much, if at all. This is probably due to the extreme difficulty of moving mineral products, bulky and unglamorous as they are, away from their

May 1, 2003

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986