Search Documents

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By J. W. Sanger

The establishment of a central steam-heating system in Winnipeg and its inauguration in October, 1924, has attracted a considerable amount of attention. Not only does it excite the curiosity of the engineer, but it has stirred financial and civic bodies throughout Canada to such a degree that there is now a much keener general interest in this particular type of public utility than has been shown heretofore. This does not mean that we may expect a mushroom growth of central-heating systems in all our larger Canadian cities in the near future, but it does mean that the pioneer work which Winnipeg is now doing will undoubtedly be used to guide others in their judgment as to the feasibility of similar projects elsewhere. The success of the municipal hydro-electric system in Winnipeg, and the low rates for electricity resulting therefrom, was without a doubt the most important factor influencing the citizens of Winnipeg to venture into this new field. The events which led up to the central steam-heating proposal in Winnipeg are interesting.

Jan 1, 1926

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By Stefan Boshkov

THE ADVENT of mining at great depth has brought to the fore the question of stresses around mine openings. The many-pronged attack on this problem is certified by the accelerated appearance, in the mining literature, of articles on various topics related to this subject (1). Whereas it may be agreed that we, of the mining profession, have fallen woefully behind in research and the development of an understanding of this important facet of the general problem of mining, it must also be accepted that the analysis of the stresses in a mine structure is usually more complex than is the case in the majority of structures encountered and dealt with in civil engineering. Whereas homogeneity and isotropy are readily acceptable for most metals, such properties are but crudely approximated in rocks. Whereas the external loads on a structure in civil engineering may be readily determined, those on a mining structure are subject to ?conjecture. Whereas the limits of the structure may readily be defined in civil engineering, the boundaries of the mining structure are, in most cases, indeterminate, and subject to intelligent guesswork, at best.

Jan 1, 1956

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By H. H. Fairfield

THE production and inspection of the materials of war involves thousands of observations. Logical action is generally based on the interpretation of many observations. The success of such action depends upon the accuracy of the observations and the soundness of the interpretation placed upon them. There are countless instances where the observer 'sees but perceives not'; that is, the significance of a group of observations is lost, due either to faulty interpretation or to no interpretation at all being placed on the results. This condition is being partly corrected in the United Kingdom and the United States (1) by the promotion of certain principles by Ordnance officials. The term Quality Control has been adopted to describe a system of studying and controlling industrial products by methods of handling observations. In these pages an attempt is made to outline in a non-technical manner some of the ideas used in the handling of observations. Of course the authenticity of the observations determines the worth of any decisions based on them. No matter how brilliant is the theory built on unreliable sampling, it is usually of little practical value. n some fields it is almost impossible to obtain observations free from bias. Let us suppose that observers of speed in miles per hour were available for judgment: (a) a bystander, (b) a motorcycle policeman, and (c) a motorist accused of speeding. The bystander might be unbiased but probably would be very inaccurate. The motorist is usually biased on the low side. The policeman is the only qualified observer and, if over-zealous, he might be biased on the high side. Conclusions drawn from large numbers of biased observations naturally would be of little value.

Jan 1, 1943

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By Patrick Frenette

Résumé La Mine Goldex entrera en production au 2ième trimestre de 2008. Pour permettre une production de l?ordre de 6960 tpj, le forage ITH à une pression de 400 psi (28 bar) à été sélectionné. Il s?agira d?une des premières applications du forage ITH à cette pression sous terre. Cet article traitera des gains anticipés et montrera certains résultats préliminaires. Il sera aussi question du bras manipulateur utilisé pour manipuler les tiges de forage. Abstract The Goldex Mine will start production in the second quarter of 2008. In order to achieve a production of 6960 tpd, ITH drilling at 400 psi (28 bar) was selected. ITH drilling at this pressure will be one of the first underground applications. This paper will discuss the anticipated gains and show some preliminary results. The use of the rod handler will also be discussed.

Feb 1, 2008

By W. L. Falconer

"IntroductionThe very recent emphasis on the importance of the northern portions of the Alberta basin as a prospective oil province has led the oil companies northward into new and undeveloped territory. Northern Alberta is a land of continuous forest, covering a plains-type topography. The plains are only occasionally broken by sharp, broad river valleys. Tributary streams head up quickly and very soon lose themselves in large undrained areas. It is these pseudo-swamps that cause most of the troubles and headaches of the oil explorer.The rivers have served as the main transportation arteries since people first ventured into this area. The bush is being pushed back, but the advance is slow and there is very little more than trappers' trails beyond a few miles from the Northern Alberta Railway lines and the recently built Grimshaw or McKenzie Highway. Indeed, bush and muskeg flank many miles of the railways and roads within as close a distance as fifty miles of Edmonton. Northern Alberta is pioneer country in the truest sense of the word, and our greatest problems derive from this fact. In all pioneer areas, the first requirement is the development of access roads, and before active oil exploraton can get down to the job at hand these roads and trails must be an accomplished fact. There are two factors in Northern Alberta which offer discouragement to the oil explorer: the first and greatest stumbling block is presented by the numerous muskegs, large and small; the second is the fact that road building uses up so much of reservation time. Of course, the second is aggravated by, and a direct result of, the first. So we come back to the main problem facing the development of the north - the muskegs."

Jan 1, 1950

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By K. Howard Poulsen

Shear zones are tabular tructures which tend to occur either discordantly within, or concordantly along the margins of, competent rock masse uch as plutons, sill or flows. They contain deformed equivalents of their host rock and are common sites for gold mineralization localized in tructure oriented y tematically relative to the shear zones and internal linear fabric. Apan from genetic implications, hear zone analysis proves useful in exploration for this type of deposit because the zones are generally wider and more continuous than associated mineralization and because there is an element of predictability to mineralization geometry (i.e. vein orientation. plunge).

Jan 1, 1986

By L. E. Djingheuzian

Introduction Cylindrical grinding mills have been used for a long time, but during many years of testing no methods were established that gave consistent results. The work by both scientific investigators and operators led very often to contradictory conclusions, and each millman was very much 'on his own' when trying to find the limits for working of his ball-mills. Fred C. Bond, in the introduction to his paper on Wear and Size Distribution of Grinding Balls, freely states that the mathematical immaturity of the grinding process "is the cause of many inefficient designs and installations as well as of much poorly oriented experimental work", and evidently he sees the solution of all our grinding problems in the discovery of the fundamental laws "which can change the empirical art into a mathematically exact science". While the writer is in complete agreement with Mr. Bond that grinding is governed by fundamental laws which can be expressed by mathematical formulae, there are so many variables in grinding, all interwoven with each other and mutually influencing each other, that the coalescing and merging of all these variables into a harmonious mathematical whole appears to be a homeric job. However, a light appeared on the horizon when it was proposed that power be used as an index of the grinding operation. It is pertinent to quote Gow, Guggenheim, Campbell, and Coghill from their paper on Ball Milling, in which they say: "Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespectve of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison a new philosophy in the stud of ball milling. Briefly this 'new philosophy' consists ' of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced variables with emphasis on the latter". But it is safe to assume that it was the work by E.W. Davis, H. E. T. Haultain, F. C. Dyer, A: M. Gaudin, J. Gross, S. R. Zimmerley, and others, that cleared the path for the authors of Ball Milling and induced them and A. W. Fahrenwald to look farther afield and thus to establish a far-reaching relationship between the power and capacity and the diameter of the ball-mills.

Jan 1, 1949