Search Documents

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

By J G Reid

In the period since 1989 the Yabulu Nickel Refinery of Queensland Nickel has undergone a transformation both in terms of the nickel laterite ore feed and the refined nickel product. These two changes were mutually supporting, as will be shown in the following paper. It had been realised since the early-1980s that the Greenvale orebody would be exhausted by 1992. Consequently planning had been in progress throughout the 1980s for the importation of overseas ore as a replacement for the Greenvale ore. The existence of extensive lateritic ore deposits in New Caledonia and Indonesia made these locations the natural focus of attention. With the three Japanese ferronickel smelters sourcing their nickel garnierite ore feed from these locations it was relatively easy for the miners to supply the overlying limonite ore to Yabulu. This limonite ore was previously discarded as waste. The Yabulu refinery now receives about 85 per cent of its ore from these two overseas sources. The transition from Greenvale ore to imported ore occurred gradually between 1989 and 1993. It was during the ore importation planning stage of the mid 1980s that Queensland Nickel commenced the technical investigation which led to the ammoniacal solvent extraction (ASX) plant installation and the product change from nickel oxide to nickel metal.

Jan 1, 1994

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

Increasing attention is being focussed worldwide on the strategic environmental assessment of mining projects, including consideration of cumulative environmental effects. In New Zealand there is now an end in sight for inappropriate delays in resource consent approval of responsible mining projects. This paper investigates six case examples of recently consented mining and quarrying projects, whose applications were notified. It also explores the nature of delays that occurred, the factors that contributed to the delays, and whether the consent process delivered fair and effective public participation and desirable environmental outcomes.

Jan 1, 2005

Almost from the beginning of civilisation the inhabitants hadlearned the art of recovering and working copper to produceitems which were of use to society.From the early beginnings of the use of copper which can betraced back 6000 years and more, there has been an evolutionaryprocess accentuated in more recent times in which the art ofproducing alloys particularly with tin and latterly zinc and otherelements, has given society a wide range of useful alloys for usein industrial, domestic and architectural applications.

Jan 1, 1995

The Australian gold industry has in recent years experienced a tremendous growth period, though not to levels prevailing at the turn of the century. There are, however, a number of dynamic factors at play which collectively indicate that it would be unwise to assume that this growth will be maintained; indeed the future discovery of viable new deposits may be insufficient to prevent an industry decline in Australia.The higher gold prices of the 1980's together with technological advances, made previously worked mining centres areas of excellent prospectivity. These resources, signposted for us by the oldtimers, are being rapidly depleted. Whilst there can be no doubt that these resources can be replaced the real question is whether it is economic to explore for new deposits when it is likely that:The cost of future exploration will increase as exploration must focus on grassroot areas with few signposts. Almost by definition this primary exploration effort will be subject to a lower success ratio.The cost of future exploration will increase as new deposits will be located in more remote areas and at depth.

Jan 1, 1986

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

By Woodcock JT

This paper reviews the chemistry of flotation pulps with the aim of gaining a better understanding of the effect of chemical environment in flotation and ap- plying the knowledge to improving the con- trol of reagent additions. Theories of flotation are considered briefly, but they are only of limited help in specifying an appropriate chemical environment and in establishing control techniques. The chemical nature of flotation pulps is reviewed. Four distinct phases are present - solids, an aqueous liquor con- taining many dissolved reactive sub- stances, organic liquids, and gases. All of these vary in many ways and interact with each other. It has now been estab- lished that there are many previously- unsuspected materials present in plant pulps that can or might affect flotation. Concentration profiles of selected para- meters in operating plants are given to show some typical changes that occur. Recent advances in collector chemistry, especially that of xanthate and related species, are reviewed. Modes of decompo- sition and/or formation in pulps of xan- thate, dixanthogen, perxanthate, xanthyl thiosulphate, and monothiocarbonate are reviewed, and their W absorption spectra are compared. Some relevant information on dithiophosphates, mercaptobenzothia- zole, and thionocarbamate is summarized, and some speculative comments are made about reactions of these collectors.

Jan 1, 1984

By J van Niekerk

The BIOX« process for the treatment of refractory gold ores and concentrates has been commercially in operation for 18 years. A total of six BIOX« operations have been successfully commissioned since the commercialisation of the process. Four of these BIOX« plants are still in operation today. There has been a renewed interest in the process the past few years with two BIOX« plants, the Suzdal plant in Kazakhstan and the Fosterville plant in Australia, scheduled for commissioning during 2004. Four new projects are also in various stages of development and are currently scheduled to be commissioned during 2005 and 2006. Research into the process are currently focussed on the two highest operating cost items for the commercial operations, namely power for agitation and air dispersion and cyanide consumption during leaching. Laboratory aeration and agitation testwork using the A340 up-pumping agitation system has shown that similar mass transfer rates can be achieved at slightly higher agitator power. The up-pumping system, however, eliminates the need for a separate blower and sparger system as air is introduced into the slurry from the slurry surface. The use of the thermophile bacteria as the final oxidation step during biooxidation has shown great promise. Reductions in cyanide consumption of up to 50 per cent were achieved when using the combination mesophile and thermophile process compared to standard BIOX« product solids. The combined process takes advantage of the milder oxidising conditions of the well known BIOX« process for the bulk of the oxidation and then uses the high temperature thermophile bacteria to complete the oxidation. The ASTERÖ process for the biological degradation of cyanide and thiocyanate containing effluent solutions has been proven to be efficient and stable. The process uses an activated sludge system with a residence time of approximately six hours in the sludge reactor. Heavy metals and metal cyanide species have also been shown to be removed successfully from solution.

Jan 1, 2004

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984

Pasminco is actively addressing the optimal utilisation of the known orebody at the Broken Hill mine, in addition to actively exploring for economic mineralisation in the region. As part of the policy of better utilising the known mineralisation a major upgrade of geological systems at the mine was initiated. The software chosen for this change was Maptek's Vulcan, mainly because of the ease of use of this package. Rather than having numerous data sources in varying software packages the mine aimed to limit interfaces and packages. The decision to upgrade the mine's software was not taken lightly, especially in view of the inature stage of Broken Hill mining operations. However, the current mine life of Pasminco Broken Hill mine is I I years, which is longer than many new mines setting up in Australia today. Also, a more sophisticated system brings with it a better understanding of the economic mineralisation, possibly extending the mine life further. The process of moving the Broken Hill databases into Vulcan was a huge task which included, database transfer, digitising, wire framing, modelling and eventually ore resource calculation. To ensure the validity of the new ore resource accounting system, the existing system was run as a duplicate for the introductory year, providing a comparison and if necessary a safety net. The benefits of such a change, however, became apparent almost immediately. Area geologists realised the opportunity to revise geological interpretations in their areas of responsibility, enabling them to obtain a better understanding of orebody morphology. Three- diniensional analysis provides an excellent method by which review of ore targets both in the underground and mine lease exploration areas can he made. As each new find of mineralisation enters the system and hopefully extends the mine life, the opportunities for further mineral exploration in Broken Hill area by Pasminco are enhanced.

Jan 1, 1997

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

The writer had the pleasure of several months' laboratory tests on a metallurgical process for copper ores devised by Mr. W. H. Corbould, Consulting Engineer, North Queensland. Mr. Corbould's research work in this direction commenced somesix years ago, and he eventually succeeded in obtaining a good extraction of copper and a resulting solution practically free from iron and other impurities. The commercial operation of the process was investigated and special machines with novel features were designed. OUTLINE OF THE PROCESS.The process described in detail in the following pages, required for successful application that the ores contain at least the minimum ratio of sulphur to copper, consistent with the production of sulphadising roasting conditions.

Jan 1, 1921

By Happ J. V

Factors affecting the rate of arsenic removal from lead bullion during softening processes were studied. Very high rates of removal could be obtained under conditions of intense agitation and ready availability of oxidant. Reaction mechanisms were proposed to explain the sequences observed. Selective removal of arsenic with minimal loss of antimony from bullion was favoured by a low temperature Harris process and oxidizing via a caustic soda medium.

Jan 1, 1987

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988