Search Documents

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

Iron ore in the Pilbara Region of Western Australia varies in composition giving iron ore a range of densities. An accurate density figure of the material leads to accurate calculations of production throughput. Density studies of two separate iron ore mines were conducted in the Pilbara. Procedures and results are reported here.The Pilbara Region of Western Australia has a number of iron ore operations. Two mines have conducted density studies of their materials. The purpose for the studies was to determine an accurate in situ bulk density that could be applied to volume and tonnage calculations of the operation. It was identified that density was one culprit causing calculation variations. Density is an important figure used to estimate ore reserves, equipment requirements, production rates and indirectly costs and sales revenue. One study was conducted at Rio TintoÆs Robe River Mine based near the town of Pannawonica. Its Mesa J orebody is currently being mined and is a low-grade deposit of goethite and hematite (Burnham, 2003). A separate study was conducted at BHP BillitonÆs Yarrie Mine situated north of Newman and east of Pardoo. Its orebody consists of high grade formed by a supergene enrichment of cherty material and a burial metamorphism to produce hematite (Richardson, 2002). The method used to determine density was by large-scale samples using the pre-mining in situ volume of the material and the weight in tonnes after mining.

Jan 1, 2003

By Richmond AJ, Allan J

The use of long-hole in-seam drilling techniques for seam gas drainage ahead of mining was introduced to the Australian coal industry by ACIRL in mid-1981. ACIRL's research program has involved the development and demonstration of drilling and borehole survey technology in addition to evaluating the gas drainage potential of long-hole in- seam boreholes. This paper presents the results of the long-hole drilling carried out to date in the Illawarra District of the New South Wales coal fields. Drilling experience in relation to both vertical and horizontal directional control of the drill string, drill performance and borehole survey techniques are discussed. In addition, results of gas drainage effected by the long boreholes are presented. Future potential and requirements for further development of this technology are Reviewed.

Jan 1, 1982

By Haines P. W, Sweet I. P, Rawlings D. J, Page R. W, Plumb K. A

Current regional geoscientific studies across the McArthur Basin as part of the National Geoscience Mapping Accord by the Northern Territory Geological Survey and Australian Geological Survey Organisation have provided a significant amount of new data which has enabled revision of the stratigraphic and chronologic framework of the basin. This paper provides an overview of these results, with particular emphasis on new results from Arnhem Land.

Jan 1, 1994

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

The object of this paper is to show in some detail the mining challenges that have been presented and overcome during the successful development of the main exhaust ventilation drive that will service the Ballarat East mine during its 20+ year lifespan. Topics to be discussed in this paper include the ground support regimes employed, the ground conditions encountered during construction, how the heading was recovered after falls of ground and the effectiveness of geotechnical probe drilling at Ballarat.

Jan 1, 2006

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

In-situ leaching of gold deposits has not become an option largely as a result the lack of suitability of cyanide as a lixiviant due to sluggish kinetics and high dependence on the availability of oxygen. A second problem area is the excessive cost of drilling the required number of injection and production wells needed to service a wellfield capable of maintaining any significant throughput or providing and acceptable level of gold production. Well spacing in in-situ leaching operations is limited by solution life, dissolution rate, and the need for solution control. With cyanide the life of an active solution capable of dissolving significant gold is severely limited by the availability of oxygen which cannot be readily replaced while the solution remains underground. The extremely slow gold dissolution rate also necessitates excessive contact periods in order to dissolve coarse gold.

Jan 1, 1991

The heavy media cyclones at Argyle Diamonds are subjected to extremely abrasive service conditions and have been the subject of a development program from the time the first ore was treated in the AKl processing plant. In the past ten years the cyclones have been re-engineered from a standard DSM design, in which some components would only last four days, to the current Argyle design in which the minimum component life is 175 days. Development has focused upon the elimination of turbulence in the cyclone and combating unavoidable abrasion through the use of appropriate wear materials.

Jan 1, 1996

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

Different mineral structures can act as mineral reservoirs for the immobilisation of toxic compounds. In the paper different mineral structures will be explained and their potential for incorporation of heavy metals and anions will be shown. The following structures will be explained (P÷llmann, 2007):apatites (incorporation of heavy metals, silicate apatites);ettringites (fixation of oxo-anions);layered double hydroxides (fixation of heavy metals, fixation of anions, fixation of organics, sorption materials); andmanganese oxides. Different possibilities of solid solution and incorporation in crystal structures will be explained and advantages of stable minerals be proved using experiences with real toxic wastes. In the process of thermal treatment the formation of primary mineral reservoirs will be shown. The precursor phases (similar to well known cement minerals) react in contact with water to form secondary mineral reservoirs (cement hydration mineral products). The formation condition of primary and secondary mineral reservoirs and their stabilities and incorporation possibilities will be shown. Examples for incorporation of various elements are given. Application for water clarification will be outlined.

Jan 1, 2008

Mount Isa Mines Limited has been mining copper ore for 50 years. In recent years, this production has been entirely by open stoping methods with cemented backfill, mostly in the large 1100 orebody.This has been the major ore source for 20 years, with smaller amounts coming from the 400, 500, 650 and 1900 orebodies. At present, the 1100 orebody is the only source, and this situation will continue until the deep 3000 and 3500 orebodies begin producing in late 1992/93. Production rates have increased to almost 6 Mt/yr, and are planned to rise to 7 Mt/yr by 1995/96. In the future, there will be a move towards variations of the open stoping system as production moves to more lensy zones of the southern 1100 orebody and to the deeper 3000 and 3500 orebodies. This paper describes current operations in the 1100 Orebody, with some indications of future directions.

Jan 1, 1993

By Phillips H. R

The action of free rolling disc cutters is well understood, relationships between disc geometry and performance having been established both in the laboratory and under field conditions. However, under severe operational conditions a malfunction of the disc bearing assembly is likely to produce a definite change of cutting action. Collapsed or siezed bearings can even prevent the disc from rolling and thereby create what is equivalent to a drag pick. This paper describes a programme of laboratory experiments using deliberately stalled discs. Their performance under such conditions is contrasted with that for a free rolling disc and also with a drag pick having a ridged front developing into a negative radiused back clearance angle. In conclusion an assessment is made of the influence stalled discs can have on the torque and thrust requirements for a tunnel boring machine.

Jan 1, 1981

The facilities used and techniques employed in the manufacture of steel and iron rolls at the Steel Foundry, B.H.P., Iron & Steel Works, Newcastle are described.

Jan 1, 1972

By Hanna P

Coal geologists are under pressure to minimise exploration expenditure, maximise interpretation confidence and produce the results often too soon. This pressure continues to increase as companies are forced to evaluate borderline economic deposits which are usually deeper and more hazardous, such as the Togara North and Togara South projects in Central Queensland.

Jan 1, 1998

To secure a sustainable competitive advantage some smelters may need strategies based on flexibility in feed and product ranges depending on immediate future projections of profitability. This paper explores the technical requirements for strategic diversity in smelting, leaving procurement, marketing and contractual considerations aside. The days when a smelting operation is tied specifically to say only processing zinc concentrates are perhaps drawing to a close. While internationally traded mineral concentrates are available, attractive business opportunities must exist for fully diversified custom smelters. Certain new and emerging technologies have inherent characteristics that are evaluated in this context. The paper identifies the basic building blocks that will permit such a scenario and assesses the technical feasibility. The ability to respond flexibly to environmental pressures is highlighted as being of paramount importance.

Jan 1, 1996

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975