Search Documents

This paper presents a summary of the technical achievements of the Port Pirie Smelter in 100 years of lead smelting and refining. It also aims to give where possible the reasons or circumstances that led to the achievements. The major achievements took place in the areas of sintering, blast furnace, copper drossing, copper recovery, lead refining and slag fuming.

Jan 1, 1989

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

By Watson K, Pollard D. M

The electrolytic recovery of metals from solution requires an understanding of the characteristics of the particular system employed, and the current efficiency and morphology of the deposit are influenced by such factors as cell design, metal ion and supporting ion concentration, acid concentration, temperature, impurity levels and cell design. The electrolytic deposition of both cadmium and silver present individual difficulties, and special cell designs are used for each of these metals. It was found that cadmium deposition was plate-like at lower cadmium concentrations, and at higher current densities. The presence of zinc in the electrolyte promoted nodular growth. Current efficiency remained high even at 50C in contrast to published information. Silver deposition morphology was relatively unaffected by changes in silver concentration, pH and current density. Current efficiency was reduced as temperature was increased.

Jan 1, 1989

The Hall-Heroult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-Heroult cell- the electrolyte, the anode and the cathodes are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride-carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.

Jan 1, 1987

By E Y. Baafi

Artisanal and small-scale gold mining (ASSM) offers lucrative employment opportunities to the locals of most developing countries. The major drawback of ASSM is its adverse impacts on the environment resulting from improper mining and processing techniques. Papua New Guinea (PNG) has very active ASSM activities. The artisanal and small-scale gold mining in PNG provide employment at local and national levels and the sector is an important source for inflow of foreign exchange into rural communities. However, small-scale mining activities are associated with sensitive health and environmental issues. The process of recovering gold by retorting and heating the amalgam over an open fire is a dangerous health practice. This paper discusses artisanal and small-scale gold mining operations in PNG and their impacts on the local environment.

Jan 1, 2008

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

By Hood M

Rock cutting excavation technologies and particularly continuous excavation technologies, can offer benefits in the areas of reduced costs, higher revenue and increased safety in a variety of mining situations. Non-explosive rock excavation technologies for example, can deliver significant benefits in the areas of dilution and improved ground support (no overbreak). This paper is an attempt to focus on the development and future of alternative rock breaking technologies and to provide some insights as to why and how we should proceed in this direction. The market size for underground hard rock excavation technologies is examined. A short review of the evolution of various rock excavation technologies in terms of cost and production rate is given and a summary of the state-of-the-art technology is presented. Mechanical excavation technologies (TBM) have very high production rates compared to D&B and the gap is widening, however, they have not been successfully applied to mining applications. Operating costs for mechanical and D&B systems have been dropping over time, however, D&B costs are the lowest. Given the current state of knowledge it appears that with regard to hard rock underground metalliferous mining that R&D efforts should be focussed in the following areas - disc cutter tool development (materials and design; operation; presentation to the rock surface), hybrid cutting systems (consisting of water jets and disc cutters) and development of pressurised hole breakage technologies. It is also possible that two techniques known as the pulsed laser and pulsed water jets may have some potential. The generally agreed specifications for a widely applicable underground hard rock excavating machine are - disc cutter based, a minimum production rate of 100 t/h, be flexible, manoeuvrable and deployable, weight of less than 100 tonnes and be economically competitive with D&B in rocks over 150 MPa UCS. Such a machine would seriously challenge the position of conventional D&B in a wide range applications and provide some of the benefits of mechanisation and automation that the mining industry is pushing so hard for. However, technology developments in the D&B area are not static and hence the target is moving and is increasingly difficult to overtake.

Jan 1, 1995

By H E. S Moorcroft, D Scott

The increasing mining depths of South African gold mine deposits are resulting in ever-increasing heat loads associated with depth and the geothermal gradient. Together with changes in the mining horizons brought about by the depletion of older, shallower, high-grade reserves, this leads to the need for the continuous review and redesign of cooling requirements. Traditionally, cooling requirements were met by using a combination of cooling strategies, including bulk air cooling on surface and underground. If this proved to be insufficient, chilled service water and secondary remote air-cooling systems were introduced. This paper reviews these practices in order to provide a cost-effective means of catering for the introduction of hydropower at the Gold Fields Ltd South African operations. Some of the equipment that has been developed to meet the requirements of both hydropower and refrigeration includes hydropower fans, cooling coils and in-stope venturis. These are individually described and discussed, together with their roles within the greater strategy. The planned change in the cooling strategy and the employment of these technologies have effectively doubled the cooling available, from 10 MW to more than 20 MW, extracted from the hydropower water used to drive the mining equipment. In conclusion, the cooling strategy described allows a total heat load of approximately 52 MW to be successfully ventilated and cooled through the use of combined surface and underground refrigeration installations, and through the use of hydropower-chilled water.

Jan 1, 2005

Surface oxidation is one of the most important factors that influence the flotation selectivity and recovery in the processing of complex sulphide ores. It is an inherent part of surface chemical reactions that determine whether the surface film formed on a sulphide mineral will act as a hydrophobic or hydrophilic one. Because of the highly complex surface chemistry and mineralogy involved the results of flotation tests may often be difficult to interpret. In this paper, the flotation behaviour of nickel-copper ores processed in the Sudbury area is discussed with emphasis on the effect of oxidation on individual minerals, primarily pyrrhotite. In general, moderate oxidation of a freshly ground ore promotes the flotability of all principal sulphides in the ore leading to a bulk flotation concentrate. The ease of individual mineral flotability under normal aeration conditions, which is chalcopyrite > pentlandite > pyrrotite, changes to pentlandite > chalcopyrite > pyrrhotite under oxygen-deficient conditions. This behaviour is correlated with the catalytic activity of these minerals for oxygen reduction. On the other hand, preferential oxidation of pyrrhotite may lead to a selectivity increase in flotation. Such a behaviour has been noted in the flotation of a pyrrhotite-rich process stream. The results have been discussed in the light of fundamental electrochemical interactions involving pentlandite, chalcopyrite, pyrrhotite, pyrite and grinding media and a mechanism has been proposed to explain the selectivity.

Jan 1, 1993

By Bilodeau M. L

The paper describes a model which has been developed to assess the economic charac- teristics of base metal investment in Canada and the effects of past, present and possible future sharing systems, particularly mining taxation systems, thereon. The model is illustrated by applying the 1976 Canadian tax system to the economic characteristics of base metal discoveries made in Canada during the 1951-1974 period.

Jan 1, 1977

Surface subsidence caused by coal mining operations was the subject of a very successful symposium organised by the Illawarra Branch of the Australas- ian Institute of Mining and Metallurgy in February, 1973. This symposium dealt with the principles of subsidence and overseas experiences arising out of underground mining. Since that time the i eew South Wales Department of Mineral Resources and Development (formerly the Depart- ment of Mines) has incorporated in the approval for pillar extraction certain conditions related to the monitoring of surface movement. Surveys and plans are required to be kept at mines where total or partial extraction of coal takes place. This paper traces the monitoring of surface movement in the Northern Coalfields of New South Wales over the past ten years. Reference is made to the National Coal Board's Subsidence Engineers' Handbook (1975) and how the guidelines expressed therein have been Beneficial.

Jan 1, 1980

By Lightfoot BW, Wand PD, Towne DV

Sampling and e.m.f. probes were used in the liquid flow from the blast furnace and in the forehearth to evaluate the performance of the copper smelting system at E.R. & S. Significant variations in temperature, oxygen potential and copper content with slag depth and with position in the forehearth indicated that convective currents were causing considerable stirring in the forehearth. This was attributed to temperature fluctuations in the stream from the blast furnace, which resulted in colder slag being underlain by hotter matte. Tracer tests in the feed to the smelter and in the feed to the forehearth revealed considerable holdup of material in the plant and confirmed that the forehearth involved small scale turbulence but little large scale mixing. The results indicated that the copper content of slag continuously tapped from the forehearth could be lowered by at least 0.15% if better settling could be achieved and means of attaining this are discussed. As part of the investigation the recovery of copper from spent refractory bricks recycled through the smelter was evaluated. It was found that the recovery was high but it seems likely that the brick material is partly responsible for a build up of solid material in the forehearth.

Jan 1, 1981