Search Documents

By Kaji S

The Tsugaru Tunnel, located on the Honshu island approach to the Seikan Tunnel, is 5,880 m long and has a "Shinkansen" cross section of 90 m2 area. The geological formation through which the tunnel passes consists of very soft rock most of which is unsolidified sandstone belonging to the Neogen. The permeability coefficient is in the range of 10-2 to 10-4 cm/s and being water bearing with a high ground water level, the ground is unstable and subject to soil outflow phenomenon. Kajima Corporation, undertaking the Futamata Construction Section (1,420 m long), excavated the tunnel by the upper half heading method with side pilots employing the following countermeasures to cope with these severe conditions.

Jan 1, 1987

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By R Fleming, G Jones

An ocean outfall is currently under construction in Christchurch, New Zealand to transfer treated wastewater from the existing treatment ponds at the city wastewater treatment plant to diffusers located 3 km offshore. The New Zealand $85 million project comprises a new pump station and 5 km of 1800 mm diameter pipeline with a design capacity of 6.0 cumecs. The pipeline comprises 2.3 km of concrete pipe installed by microtunnelling and 2.7 km of polyethene marine pipe installed by dredge and lay. This paper describes the consent process, key environmental and community constraints, the tender process, risk provisions included in the contract, the type of contract, partnering provisions, geotechnical design issues and the pipejacking construction activities and issues.

Jan 1, 2008

By Ciminelli VST

Thiourea leaching has been applied to a refractory gold concentrate previously treated by bacterial oxidation. Following the bio-oxidation, gold has been leached in acidic thiourea solutions, under different pH(1 - 2.4), thiourea concentrations (2 - 15 g/1), ferric ion concentrations (0.04 - 3 g/1) and temperatures (298 - 333 K). Through this procedure, it was possible to increase gold extraction from 40 to 77 per cent. The increase in temperature raised gold extraction and reduced reagent consumption. Sodium sulphite addition was also very effective in lowering thiourea consumption. Staged leaching operations with interstage acid washing and carbon-in-leach experiments were tested, in an attempt to increase gold extraction. The results of thiourea leaching were compared with those obtained with cyanidation.

Jan 1, 1993

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By Wenya X, Bingchen C

About 60 per cent of magnesite ores of Haicheng Magnesium Mine, due to their low grade, are not currently commercially exploitable. In this paper, the flotabilities of the main component minerals of the ores were studied in detail with ether amine as collector. Based on. these, a new technique of reverse-direct flotation with single etheramine as collector for the beneficiation of the ores was developed. It gave highly satisfactory results. On the basis of the calculation by means of CNDO/2 method, of the studies of the solution chemistry of magnesite and of the adsorption tests and Zeta-potential measurements, the key mechanism in the new technique about activating effect of Ca2+ on the flotation of magnesite was suggested.

Jan 1, 1993

By D MacKay, W J. Bruckard

One of the mining worldÆs greatest challenges is to effectively use consumables (ie reagents and grinding media) to maximise metallurgical response, while minimising operating costs. It is anticipated that this paper will provide a logical frame work within which this can be achieved. The current study, at PerilyaÆs Broken Hill concentrator in the lead primary grinding/roughing circuits, examines the dependency of collector adsorption on Eh. The data demonstrates clearly that under the right grinding chemistry the addition of a xanthate collector during grinding can improve galena flotation. Further, operating the ball mill under the desired grinding chemistry regime leads to significant reductions in collector consumption whilst maintaining the metallurgical benefit.

Jan 1, 2008

The Escondida Porphyry Copper Deposit, located in Chile's II Region 160 Km to the southeast of the city of Antofagasta, is currently owned by Minera Escondida Limitada, a company comprising The Broken Hill Proprietary (57.5%), Rio Tinto Zinc (30%) a group of Japanese companies represented by Mitsubishi Corporation (10%), and the International Financing Corporation of the World Bank (2.5%) (Fig.l)By 1983, most of the reconnaissance drilling was completed and prefeasibility studies were regularly updated as new drilling results were reported and project concepts re-evaluated (Fig.2). In October 1982 the project was transferred from Exploration Management to Operations. By the end of 1984 project pre-development activities, including inpit development drilling, geological exploration, water resource definition, an underground bulk sampling program and the initial project feasibility report, were completed.

Jan 1, 1990

By Sullivan BJK

The 1100 orebody is a massive copper sul- phide orebody which contains a major portion of the Isa Mine copper ore reserves of 130 million tonnes at 3.2%. The underground mining of a deposit as large as the 1100 orebody is technologically a complex operation as extraction strategies have to be evaluated with reference to 1. rock mechanics considerations, 2. safety and environmental standards, 3. production and operating require- ments and 4. metal recovery and costs. The mining philosophy in the orebody has undergone considerable change over the past five years as a result of experience and improved technology. At this stage, primary stopes are extracted by high rise sublevel open stoping and pillars by slot and mass blast drawn either under rock fill or as an open Stope.

Jan 1, 1978

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

Pan Australian Mining lid installed a milling and gold leaching plant designed to process 2 million tonnes per annum of breccia sulphide ore. This plant was commissioned in January 1989. Since commissioning, increased ore reserves have been established and the plant has been expanded by the addition of one ball mill and several tanks to increase the design capacity to 3 million tonnes per annum. This additional plant was commissioned in May 1990, bringing the total number of mills up to three, each 4.5 m diameter x 7 m long. The paper details how milling rates have been increased at the expense of grind size to increase the capacity of the original plant from 2 million to 3.1 million tonne per year rate before the additional ball mill was Commissioned.

Jan 1, 1991

By J Finlay, P Betts, D Milton, H Williams

The aim of this paper is to present an innovative method to help delineate potential target volumes for haematite-goethite mineralisation as opposed to more magnetic ores. This is achieved through interpretation and modelling (2.5D and 3D inversions) of ground magnetics and gravity surveys over the Koolanooka South prospect in Western Australia. The targets are assumed to be dense and weakly magnetic and hosted within banded iron formation (BIF) horizons. Geophysical interpretation (2D map) was performed using a variety of processed magnetic and gravity images (Betts et al, 2007) to determine the distribution of lithologies, to understand the structural architecture and to map out any anomalous areas of excess density (possibly indicating goethite alteration). The created geological map is used to build geological cross-sections (geometrically consistent) that were modelled (in 2.5 D) against both potential field datasets. The crosssections are consequently used as the framework to build a 3D geological model. The model defines 3D volumes of rocks including several BIF horizons. The distribution of densities and magnetic susceptibilities of the BIFs is inverted within the GOCAD«-VPmg environment to reduce the misfit between the response of the model and the observed gravity and magnetics. By combining the results of both petrophysical property distribution it is possible to map out (using classical GIS type queries in 3D) volumes of higher density and lower magnetic susceptibility.

Jan 1, 2009

By Rao SR, Finch JA

Sphalerite flotation without Cu activation in the presence of iron ions has been reported and studied as a function of pH, dissolved oxygen content and pulp potential with both single mineral and ore samples (Leroux, Rao and Finch, 1987; Xu et al, 1992; Zhang, Rao and Finch, 1992). The flotation was attributed to ferric hydroxy xanthate. As a prelude to surface analysis to try to identify the species responsible, bulk precipitates formed from iron salt and xanthate solutions under different conditions were obtained and analysed. Analysis techniques included ultraviolet spectroscopy,infrared spectroscopy, X-ray diffraction and Mossbauer spectroscopy. It is tentatively concluded that the bulk precipitates contain three ferric components, two hydroxy xanthates (Fe(OH)2X and Fe(OH)X2) and iron oxide (FeO.).

Jan 1, 1993

Good morning ladies and gentlemen. It gives me great pleasure to talk to you today about a pet subject of mine, on when to mill and when to leach gold ores. According to Gold Fields Mineral Services of London, gold production in the United States in 1989 amounted to about 8.5 million ounces (259t), an increase of 29 per cent over 1988 and 67 per cent over 1987. The U. S. Bureau of Mines reports that from the major producing states of Nevada, California, Montana, and Alaska, some3.2million ounces of the 1989 production were produced from milling gold ores and 2.3 million ounces from heap or dump leaching. Ap- proximately 45 million tons of ore were milled and 140 million tons of ore were heap or dump leached.

Jan 1, 1991

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

As Project Managers for the Blair Athol Coal Mine Project, CMPS selected a number of computer systems to assist in project control. The areas where computers were used were: 1) Planning & Scheduling 2) Procurement Reporting 3) Document Control 4) Accounting 5) Cost Control 6) Control of project management and engineering manhours The computer packages selected were generally effective in their own areas. During 1982, CMPS acquired an in-house project control package called GC/Cue. Project control systems for the project are progressively being set up on this system. The advantages of this type of system are: 1) Improved accessibility of information, due to on-line operation and the use of VDU's. 2) Improved turn around time for computer runs and production of reports. 3) Improved presentation and format of reports. 4) Lower costs.

Jan 1, 1983

By Siemon J. R

It is possible to use compacted anodes formed at low pressure for the direct electrowinning of lead from sulphide concentrates. An anode containing 5.5 per cent graphite, formed into a compact at 34 MN m-2, enables lead to be won at a current efficiency of about 80 per cent; the power consumption .at 150 A m-2 current density being 0.4 kWh per kg lead. It would be necessary to use diaphragm cells to obtain a sufficiently pure product. A conceptual design for a full-scale plant is presented, together with a cost estimate for the production of lead by a process based on direct electrolysis of compacted concentrates. It is unlikely that the proposed process will be economically competitive with the conventional lead smelting.

Jan 1, 1976

By Jin C, Shi X

The electrochemistry of leaching gold with thiosulphate has been studied systematically by using electrochemical techniques. Results show that the current peak of anodic dissolution of gold occurs at about 50 mV(SCE) and there is passivation in the polarisation curve in the thiosulphate solution in the absence of ammonia. Ammonia markedly improves the anodic dissolution rate of gold and reduces the passivation as well as making the current peak shift negatively. Results also show that there is no current peak for a cathodic process in the range of 0 -900 mV(SCE) in the thiosulphate solution in the presence of oxygen but absence of cupric ions and ammonia. In the solution containing 0. 1 mol/L cupric-ammonia ions, the peak occurs at about -400 mV (SCE) and the cathodic process is characteristic of a catalytic reaction. Oxygen presents a predominate effect on the cathodic process. Based on the electrochemical investigation, the following mechanism of leaching gold with ammoniacal thiosulphate has been proposed. Ammonia reacts primarily with gold ions on th anodic surface of gold and the formed A (NH3)2+ rea~s then with S2O 3 in solution to form the stabler Au(S203) 2 . Cu (NHS) 4 gains electrons on the cathodic surface and is reduced to CU(N) ? which is then oxidised by oxygen and regenerated into Cu(NH3) 4 after entering the solution.

Jan 1, 1993

We all live in professional silos û comfort zones, where we talk to like-minded people with the same training, experience and view of the world. We note in passing the existence of other disciplines, but they are tolerated rather than embraced. To the geologist, the metallurgist is a mad scientist conjuring gold out of some foul solution about which the less said the better. To the metallurgist, the geologist is a bearded, self-appointed sage who guesses what is under our feet by sniffing the air, and drives a Land Rover badly. As to the view of mining engineers held by both geologists and metallurgists, this is best left to the imagination. And of course we are all confused by the term æmetallurgistÆ. I am called a metallurgist though my skills are in mineral processing not metal processing, but I canÆt be called a mineralogist because that definition is already taken. *Please note that this is available as an extended abstract only*

Jan 1, 2005

By Dawes S

Efficient roof control in colliery operation is a factor that must be maintained for· the maximum reQovery and economic extraction of the mineral. It must be carefully considered in each of the following stages in the life of a mine.1. The primary development and the first working of the mine.2. The maintenance of access roads, intake and return airways.3. The extraction of pillars.FACTORS IN ROOF CONTROLThe main objects of roof control are: The support of the roof in working places, the relief of roof pressure from the workings during pillar extraction, and in some instances the prevention of subsidence of the surface.The support of the roof during development operations and first working, and the subsequent maintenance of these is influenced by:-1. The depth of the seam below the surface.2. The thickness of the seam.3. The dip of the seam.4. The condition of the roof and floor.5. The method of extraction-mechanical or by hand.6. The method of. working-Iongwall or bord and pillar.7. The availability of material.As a general rule, the pressure exerted by the superincumbent strata may be taken as one pound per square inch for each foot of cover, and the crushing strength of coal as 1,500 to 2,000 lb. per square inch; this, of course, varies, but from these figures it may be assumed that seams below 2,000ft. in depth are liable to crush. If any part of the seam is removed, added weight is thrown onto the remaining coal. It is therefpre essential that for effective working this extra weight must be removed or supported as soon as possible.The outstanding principle in the support of mining excavations is to ensure that the supports are set as soon as possible after the natural support has been removed.Where a system of bord and pillar is applied, the early setting of supports reduces the extent to which the roof bends, thereby reducing the liability to ·tension fractures at the centre of the road.

Jan 1, 1947