Search Documents

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Moxon NT, Torrace AC

The detonation pressure of an explosive is a function of its density and its velocity of detonation (VOD) and relates directly to the degree and manner in which the explosive loads the surrounding rock. The suitabil- ity of an explosive to any particular situation is determined not so much by the total energy released but more by the rate at which it is released. As the science of rock blasting advances it is becoming economically more important to quantify explosive performance, particularly with respect to quality control and fragmentation. As part of a major explosive user, BHP Central Research Laboratories have developed a number of tech- niques to determine the detonation characteristics of explosives. These include a method of continuous velocity of detonation measurement based on the SLIFER principle. This not only enables the VOD of the explo- sive to be determined, but also has the versatility to allow factors such as under priming, slow run up, the effect of water, variable energy load- ing and the velocity of the shock wave in the stemming to be assessed. Multi point VOD systems have also been developed for more routine appli- cations. With a minor modification they can be used to determine the absolute delay of detonators accurately and economically. Direct deto- nation pressure measurement methods have also been developed based on piezoresistive techniques. Future developments include the incorpo- ration of all the above techniques into a single, portable package, allow- ing easy use on the mine site.

Jan 1, 1988

The aquifer at Phosphate Hill, north-west Queensland, presents special management challenges. The site contains a phosphate rock mine, fertilizer plant and camp. All of the site water is provided by the Duchess Embayment Aquifer, located within the Burke River Outlier of the Georgina Basin. The Duchess Embayment is a triangular shaped, Cambrian marine sedimentary basin consisting of siliceous and calcareous phosphorites, shales, siltstones and sandstones. It is fault-bounded on all sides and has a regional dip of 5¦E. The aquifer is largely confined to the siliceous facies of the Beetle Creek Formation. It has a very flat potentiometric surface and an average thickness of 45 m with confining beds above and below. The siliceous facies derives from weathering of the calcareous phase and is highly transmissive while the calcareous zone itself contains less water and is dependent upon interconnecting fractures for its permeability. Recharge appears to occur where the siliceous facies crops out around the edges of, and within, the Embayment. Aquifer management issues revolve around two points: successful dewatering of the orebody for mining; and efficient management to maintain water quality and ensure supply over the predicted 30-year life of the project. Current operations are extracting water at levels much below that originally estimated. This is having a detrimental effect on mine dewatering with the SWL lowering at a rate slower than anticipated. As a result, ore parcels are now beginning to intersect the water table, providing a major constraint to the mining plan. The aquifer drawdown cone is extensive and very flat so to keep the water table at an appropriate level for mining the management plan will include more aggressive dewatering to lower the level of the entire aquifer. The additional water will either be disposed of downstream or stored in a holding dam or via the use of artificial storage and recharge. Water resource management will also need to maintain the current quality. About 37 per cent of the water currently extracted forms the low chloride supply required by the ammonia plant and the power station. This ratio is expected to remain applicable under any future operating conditions but the low chloride resource is restricted so will require prudent management to enable the supply to continue. At current usage rates aquifer recharge versus use will need careful monitoring to ensure that the resource remains viable in the long-term.

Jan 1, 2003

By S Mitra, B J. Monaghan, T Honeyands, G Evans, R Chowdhury, D Scimone

Due to the harsh operating conditions, wearing of the inner refractory lining in a Basic Oxygen Steelmaking (BOS) furnace reduces the useful life of the refractories and incurs a significant cost component for relining. In this study, firstly, a combined compressible and incompressible computational fluid dynamics (CFD) model was developed to identify the potential wear prone zones in an industrial scale BOS system during the supersonic oxygen blowing phase by quantifying the wall shear stress distributions. Next, the retained slag splashing process was simulated by introducing an inert gas to residual slag mass to achieve a protective coating on the refractory walls. Effect of both design and operational parameters such as lance head configuration, lance position and the initial slag volume on the slag wall coating performance were quantified and most favourable conditions were determined.

Jun 19, 2024

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

This paper records the observations of faulting in the Black Star mine workings. By classifying the faults into two groups, i.e., strike faults and transverse faults, and by pointing out the differences between the groups and their effects on the silver-lead-zinc orebodies, a time relationship between the two groups of faults and the sulphide mineralisation is suggested.GENERAL GEOLOGY AND MINERALISATIONFolding and faulting are closely related to the mineralisation in the shales by silver-lead-zinc and iron sulphides.Commonly the various sulphides are fine-grained and closely associated with one another. However, exceptions do occur locally, where massive coarse galena, sphalerite, pyrite, and to a lesser extent chalcopyrite, have been observed singly or closely associated one with the other.In the main, the sulphide mineralisation forming the orebodies occurs as replacement of, and infilling along, the sheared bedding planes of the finely bedded shale host rock.The shales in general strike north-south with an average dip to 60° to the west; strong shearing along the bedding planes is evidenced by much slickensiding and slaty cleavage.Sequences of finely bedded shales of varying stratigraphic thicknesses alternate with very. massive beds, and it is in the more highly sheared thinner beds that the greatest concentration of sulphides occurs. The unmineraIised massive beds of shale, 11 in. up to 12 in. in thickness, occur singly or in groups between, and to a lesser extent. within, the orebodies. The massive beds resisted sulphide replacement and impart to the orebodies a most prominent banded structure.

Jan 1, 1953

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

By Fallins J

THE John Darling Colliery, owned by The Broken Hill Proprietary Company Limited, is situated 12 miles south of Neweastle, NSW and about 1 mile from the ocean. The area of the holding is approximately 10,000 acres, about half of which underlies the Pacific Ocean. The area was proved to be coal bearing by diamond drill boring: this method not only proved the coal to exist, but gave the depths from which could be calculated. It also proved the existence or otherwise of heavy faulting, which is a very important factor in the design of the underground lay-out of a mine. The location of shafts had to be carefuIly studied, and, before final selection, the following salient points had to be considered:Railway communications.Flood waters.Boiler feed water.Surface buildings.Probability of coal washing.Underground haulage arrangements.Lengths of roadways from a ventilating viewpoint.Before the shaft sites were finally selected, an underground design was prepared to determine the direction of the main drives in relation to the boundaries of the holding, and the of the coal seam: the latter, being an important factor in this particular locality, was ascertained by a geological survey of rock outcrops in the neighbourhood. Size of shafts was the next subject for consideration. This was determined by output, number of seams to be worked, amount of ventilation required, and, on...

Jan 1, 1930

THOSE who dabble in m.ining are no exception to the general rule that persons who know a little of a subject are apt to think that they know all about it. Some colour may be lent to the belief that anyone may succeed in mining when we hear stories ofsuccessful diggers and others who have accidentally dropped on to something good through no foresight on their part; but we seldom hear the contra account of the far larger number who fail. Those who go more thoroughly into the subject, and take up mining as a profession, know very well that it is not one that can be carried out successfully by rule of thumb, but when they point this out to the public they are credited with trying to make it a closed profession; and outsiders are for ever trying to find out the 'trade secrets,' at the same time spurning the main one, which is hard study, experience, and the ability to apply their knowledge.The average mining man is not rich. When he amasses a fortune it is generally through speculation rather than professional work, thought no doubt his technical knowledge may have assisted him. However, making a fortune and running a mine are twodifferent things.

Jan 1, 1911

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

By B Yang, L Wang, C Y. Ng

Flotation process intensification is often achieved through changing chemical reagent scheme or flotation machine or both, which likely brings a hefty burden to the flotation plants in terms of capital or operating expenditure. A novel approach to flotation process intensification is the use of acoustic sound, which has been demonstrated to be effective in improving the flotation of various mineral systems with different type of flotation cells. This approach was based on the dynamic stabilisation effect of acoustic sound on the flotation froth. The present work aims to understand the influence of various experimental conditions on the effectiveness of the approach. First, the effects of sound frequency and amplitude were studied with column flotation of silica particles. Results showed that the flotation performance was improved only within a certain range of frequencies and above certain amplitude. The study was then extended to the mechanical flotation of quartz particles with various size ranges and at two solids concentrations. With sound, the recoveries of different size fractions within the range of 20–212 μm were all increased. In particular, the recovery of 150–212 µm particles was increased from 0 per cent to approximately 25 per cent, demonstrating the potential for extending the upper limit of particle size in flotation by using acoustic sound. Furthermore, mechanical flotation of chalcopyrite particles at various collector dosages (50–150 g/t) was carried out with and without sound. Results showed that the increment of the final flotation recovery was increased with sound at different collector dosages. Overall, acoustic sound has the potential to be used as an effective and versatile method for flotation process intensification.

Aug 24, 2022

By Quinn P, Robertson G, Agar GE

The replacement of diphenylguanidine (DPG) for separating INCO Bessemer matte with a water soluble collector requires a frother since most collectors do not have frothing properties. The objective of this study was to identify a non persistent frother which produced a deep froth and collapsed rapidly, while maintaining acceptable metallurgical separation. Incremental rougher flotation tests failed to differentiate any metallurgical benefit through the use of a specific frother, so other tests were employed to identify the candidate frother. The equilibrium froth height and rate of froth collapse (froth stability) of several commercial frothers were evaluated as a function of frother concentration using a 'frothmeter' apparatus. Frothers evaluated were methyl isobutyl carbinol (MIBC), Pine Oil, triethoxy butane, Dowfroth SA1263, Dowfroth 250C, Dowfroth 200 and Allied Colloids CRNI-1002. Dowfroth SA1263 produced the largest froth height, and TEB had the greatest rate of froth collapse. Frothers with properties similar to Dowfroth SA1263 and Dowfroth 250 were rejected due to their persistent froths. TEB was rejected because it has a low flash point and Pine Oil could be a nuisance to add to a flotation column. Therefore, the preferred frothers were declared to be Dowfroth 200 or Allied Colloids CRNl-1002.

Jan 1, 1993