Search Documents

In the traditional analysis of airblast and ground vibration, it is often assumed that only that single blasthole possessing the maximum charge weight (or a small group of blastholes initiating in an 8 ms time window) will determine the peak level of airblast or vibration. This assumption is examined in light of waveform superposition, and is found to be unsound. More rational alternatives are given in which all blastholes (or a selected number of blastholes) are assumed to contribute, in varying degrees, to the peak vibration or airblast. However, it is also shown that there is generally no precise solution for determining the number of blastholes that contribute to the peak level. The technique of waveform superposition does not rely on evaluating which group of holes produced the peak, and so is the preferred method for prediction. Some numerical and analytical models of wave superposition for airblast and vibration are also reviewed and recent approaches discussed. The directionality of airblast, in particular, is analysed in detail using a new superposition model that is constructed of two submodels, onenumerical, the other analytical. This model shows that the airblast from even a single blasthole can be highly directional. The detail of this model is commercially sensitive and will not be discussed. Only results and a broad discussion will be given.

Jan 1, 2004

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

By Rosmus P

Improper use of auxiliary ven- tilation units during heading operations may often result in the appearance of hazardous methane accumulations. This is the case especially when roadways are ventilated by a combined system with a short sucking pipe at face end performing as the dedusting installation. Uniform air inflow to the face end facilitates sucking off the dust clouds and creates conditions favourable for formation of local methane accumulations. The highest methane concentration occurs in the cutting zone between the rock cut and the pipe inlet, under the roof and by, the sidewalls. Permanent monitoring of methane concentration at face end employs methane sensors. The most important are: one on the road- header's boom behind the cutting head, and one at the air outlet from the dedusting installation.

Jan 1, 1988

By Walters GW

A countercurrent method of metal refining using crystallization and reflux is discussed. 4n account is given of the development of this technique for the separation of silver and bismuth from lead using bench-scale studies to the present small pilot-plant unit (around one tonne per day) in the "Commonwealth Scientific and Industrial Research Organization (CSIRO)" Division of Chemical Engineering.

Jan 1, 1975

By P Hayward a, P Evans, K Prince, F Radke

Operating efficiency is becoming paramount as the mining industry moves towards globalisation and conglomeration. Mining companies are continuously searching for new technologies that can improve plant efficiency, by reducing operating costs and maximising metal recovery. Identification of how gold losses occur within an operating plant is crucial for determining appropriate operating strategies for improved metallurgical performance. Classical mineralogical and metallurgical techniques enable the operator to identify where losses occur in terms of particle size and mineral associations, however how the gold is hosted within the mineral grains (for example, as solid solution or as fine micro-inclusions) is more difficult to determine. This paper provides details of the testwork methodology, and resultant laboratory study to improve gold recovery.

Jan 1, 2004

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981

Robertson Diasol have developed a spectral gamma-gamma tool fully able to withstand borehole conditions. Spectral data is digitally recorded across 256 channels depending on energy levels of the photoelectric effect. Data processing is being developed with the objective of calibrating channel amplitudes to mineral type which will lead to a direct log of selected mineral grade as a continuous trace with depth.

Jan 1, 1990

By Takiuchi T, Kurita M, Owada S

This paper describes the possibility of the application of flotation to the separation of monazite from xenotime and of columbite from ferberite, which have been said to be difficult with generally used physical beneficiation methods. For Malaysian monazite and xenotime samples, a great difference is observed between the flotation recoveries at pH 7.5 using 1.0 x 10-4mol/1 dodecylammonium chloride (DAC). The grade and recovery of columbite in the binary flotation with both minerals result in 85 per cent and 67 per cent in the cleaning froth and 91 per cent and 51 per cent in the re-cleaning froth, without adding any scavenging stages. For monazite samples from various localities, the flotability is dominated by the electrostatic interaction between mineral surface and collector ion using DAC as collector, but the singular decrease of flotation is observed in the sample of which the crystallinity is low and the surface structure is rugged and complex. Otherwise, ferric ion in the flotation system probably dissolved from mineral is found to activate the flotation using sodium dodecylsulfate as collector. For columbite and ferberite, the separation is judged possible at pH 3.0 using 1.0 x 10'3mo1/l sodium oleate (NaOl) from the single flotation results of each mineral. In the binary flotation, however, columbite recovery in the froth is greatly diminished below that expected. This would be because NaOl is prevented from adsorbing on the columbite surface of which the charge is transformed more negative side by the specific adsorption of the tungstate ion dissolved from ferberite.

Jan 1, 1993

The introduction of new technology into thegold-mining industry has been encouraged in recent years by increases in the price of gold andthe necessity for costs to be contained.At most new gold mines, run-of-mine millingis preferred over crushing and multistage milling, and this change at the head of the circuit leaves no place for the manual sorting of ore and for gravity concentration in the mill circuit.Flotation continues to hold its place in goldrecovery. However, a decline in the demand forsulphuric acid may limit the amount of pyrite thatcan be roasted before cyanidation.

Jan 1, 1984

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By Kavetsky A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits, this is largely dependent on muckpile shape and looseness within a muckpile. Moreover, prediction of grade boundary movement and subsequent dilu- tion is of interest to most open cut mines. Such a predictive tool would enable blast design changes to be made to reduce mixing of certain grade regions. At the very least, a good knowledge of post-blast region bound- aries can reduce layout of the grade boundaries and decrease grade dis- crepancies between pit and plant. The model presented in this paper is able to consider various options for a production blast and predict consequent muckpile shapes and grade boundary movements in a three dimensional manner. The overburden geometry, hole patterns, hole inclination and charge distribution are all explicit model inputs. The model divides the rock mass into blocks and calculates a velocity for each block. Three controlling parameters are used in the model, which are related to the explosive energy per unit length of blast hole, energy attenuation of the rock mass and inter-row delay, respectively. The output of the model is a 3 dimensional muckpile shape (contour or any cross section) and a contour map of grade distribution within the muckpile. The model parameters are site specific, since their values depend on the rock condition and explosive-rock interaction which varies from site to site. In order to "tune" the model to a particular site, parameter values must be found which reproduce an observed muckpile profile shape from a given blast design. This calibration of the model requires at least one surveyed muckpile profile shape from a production blast. The model parameters which best reproduce that shape are found by a pattern search technique, and may then be used to predict the effect of changes in blast design on muckpile profile shape and grade boundary movement.

Jan 1, 1989

Creating Value and Improving Environmental Performance by the Recovery of Valuable Products from Tailings from the Athabasca Oil Sands in Alberta, Canada

Sep 13, 2010

The Hunter Valley Rail Project (HVRP) represents most of the coal producers using the Hunter Valley Rail System in NSW to haul coal to the port of Newcastle. This system carries over 70 per cent of NSW's coal exports, comprising over 30 per cent of total Australian coal exports. Hunter Valley coal is the largest export industry in NSW, and one of its largest export growth opportunities. However, the industry is under intense pressure in international markets from existing and new coal producers and from other energy sources. Whilst potential growth in demand is substantial, particularly for thermal coal in Asia, excess world supply has pushed prices down, and this underlying trend may well continue. The industry has lost international competitiveness and as a result, investment has dropped 44 per cent over the last two years. The industry must be rapidly structured to compete and attract investment on the basis that these pressures will continue. Substantial productivity improvement and cost reductions must be made for the industry to regain competitiveness, otherwise growth will not occur and the industry will decline, with serious implications for the Australian and NSW communities. The introduction of internationally competitive rail freight rates is an urgent and essential part of this process. It is the key objective of the HVRP.

Jan 1, 1995

A simple production technique has been initiated and implemented at Oaky Creek open cut coal mine to optimise recovery of coal from the relatively thin geological seams. The production technique is based upon minimising coal dilution through careful dragline operation and the selective use of mine mobile equipment to clean the top of coal. In addition, recovery of coal from the pits has been increased by refining blasting and dragline methods.The implementation of the recovery optimisation programme at Oaky Creek has provided significant economic benefits from increased yield through the preparation plant by the reduction in dilution, and from increased raw coal tonnage through improved pit recovery methods.

Jan 1, 1990

The problems encountered with the introduction and use of Isanol underground are described. Significant direct as well as indirect savings have resulted from the use of Isanol. Field studies have shown that the concentration of common gases released during detonation is considerably lower than with conventional nitro-compound type of explosives.

Jan 1, 1977

The Woodlawn base metal sulphide deposit, located 50km S of Goulbum, New South Wales, was mined as an open pit operation for 10 years from 1977, producing 8 million tonnes of ore. Underground development began in 1985 and reached full production of 500,000t/yr as open pit mining ceased in mid 1987. Underground development highlighted the extensive deformation and intense alteration associated with the deposit and the host rocks.The deposit occurs above an acid volcanic pile in a sequence of interbedded and interfingering shales, cherts, volcanogenic sediments and pyroclastics of mid to late Silurian age intruded by dolerite sills.

Jan 1, 1990

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993