Search Documents

By Brett D

Tailings disposal and water management are one of the most important environmental issues in mining projects. The nature and the method of disposal of the tailings will determine the long term environmental impacts and must be carefully considered at the planning stage so that final abandonment can be economically achieved. If not, long term and on-going treatment and amelioration may be required to achieve environmental standards. Final abandonment requires dam safety surveillance inspection to satisfy engineering stability and hazard requirements as well as environmental issues. Environmental issues include stability, as well as rehabilitation and long term contamination potential.

Jan 1, 1991

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

Environmental impact and rehabilitation on completion are primary considerations in obtaining approval for mine projects from government authorities.This paper focuses on the planning and commencement of rehabilitation during the mining of an open cut mine (Hedges Gold Mine) in an environmentally sensitive area in the southwest of Western Australia.

Jan 1, 1992

By Peck WH

For many years it was realised that the methods used for unloading concentrates at Port Pirie were inefficient and labour intensive, therefore, when a decision was reached to standardise the east-west rail link from Sydney to Perth, the opportunity was taken to consider entirely new schemes for the handling of concentrates at Broken Hill and Port Pirie. After considerable testing and investigation, it was decided to install a completely new concentrates handling plant incorporating a tippler at Port Pirieòto replace the previous long established methods of unloading and dis- tributing concentrates to the operating plant.and the shipping berths. To achieve this, wagons of concentrates from the various mines are marshalled in a set order at Broken Hill and conveyed to Port Pirie in 56-wagon trains. On arrival at Port Pirie, the wagons are checked and moved to a position where they come under the control of the automatic wagon marshalling equipment.

Jan 1, 1975

By Taylor RN

A simple apparatus for delivering pulverized coal as fuel to a SIROSMELT lance is described, and its performance in smelting tests is evaluated. Using the pulverized coal as fuel, the SIROSMELT furnace performed well in both oxidative copper smelting and reductive smelting (zinc fuming). In both cases the evidence suggests that part of the combustion occurred by indirect oxidation of coal particles entrained in the bath. Oxygen potential measurements made during the zinc fuming tests confirmed the general features of the the non-equilibrium mechanism for zinc fuming proposed by Richards and Brimacombe. The zinc level in the slag during continuous fuming was lower than was predicted using an equilibrium model.

Jan 1, 1987

German coal mining suffers from rock temperatures up to 600C which are the same as in South Africa at 3000 - 4000 m of depth. Therefore cooling plants have increased in the last decade and today a cooling power of nearly 200 MW is installed in the total Ruhr District. Cooling a mine is a little bit different from cooling a bottle of beer in a refrigerator in the kitchen because the heat taken from the bottle of beer is delivered to the kitchen some centimetres away; in mining the cooling-problem is more difficult: here the bottle of beer corresponds to the airflow at the coal face and the kitchen to the surface, So it is necessary to transport the heat or the "coldness" a long distance. In the address by Ieuan Morris some systems for transporting heat from the coalface to the evaporator of the cooling machine and further from the condenser of the machine to a return airflow were described. The following is a short idea of the way this problem is treated in Germany.

Jan 1, 1983

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

In the future to excavate sufficient coal for power generation, two dredgers would be required to dig overburden or interseam 70010 of the time and three dredgers 40010 of the time. One overburden system was not adequate for this requirement, making coal production reliability vulnerable. TS5 spreader is the new machine element of this system. The selection of the best type of machine configuration to suit the application was then subject to an internal SECV VE Study, a registration of interest and a tender for two machine alternatives. This paper outlines the reasons why SECV planned the Secondary Overburden System and how the Krupp machine met these requirements. It also identifies the main design features of the machine and its constructability which will allow the machine to be operational by the end of May, 1990.

Jan 1, 1989

For many years the mining industry at Broken Hill, New South Wales, Australia, was carried on with just sufficient attention to underground ventilation and hygiene conditions as to keep pace with necessity. However, the campaign against industrial diseases in other mining centres (notably South Africa) some years ago, brought the subject more prominently before local mining engineers.Throughout a period of several years, gradual improvement has been effected, and at the present time industrial hygiene is considered an essential part of the production operations of the various companies.In June, 1918, a move was first made by the Board of Trade advising an inquiry respecting the health of employees engaged in the metalliferous mining industry in the State of New South Wales. At the end of that year, a recommendation was made to the State Government by the Board of Trade that a Techni.cal Commission of Inquiry be appointed to examine and report upon the dust conditions of the metalliferous mines at Broken Hill. Following this a second report presented in 1919 made specific recommendations in respect to the scope of such a Commission. A Technical Commission of Inquiry was accordingly appointed and arrived in Broken Hill to inquire into the prevalence of miner's phthisis and pneumonoconiosis in the mines. Early in March, 1920, the examination of all mine employees commenced, and the work was completed in June, 1920. The full report of the activities of the Commission and the conclusions arrived at was officially published at a later date. Based on the recommendations...

Jan 1, 1940

Water is a key resource input to copper heap leach operations in both quality and quantity. A number of recent developments in analysis of the technology have shown that water consumption can be optimised. The leach consumption has been generally considered in terms of minimisation of the evaporative loss by changing the application method (drippers or wobblers). Modelling of the irrigation effects on leach rate has shown that the poorer surface coverage from drippers has an adverse effect on the leach extraction rate. This is particularly evident in the early part of the leach. The use of different irrigation systems during alternate parts of the leach cycle can have benefits in minimising the water consumption without an unacceptable outcome from extended extraction times. By combining the leach rate effect with the evaporative loss estimates, an economic decision matrix can be generated to allow the operator to select an appropriate leach irrigation strategy, combining both irrigation delivery and irrigation rate. In the SX-EW plant, the total quantity of EW bleed and SX scrub stage bleed (both for iron control) can be reduced to an absolute minimum. The economic minimum may be different depending on the cost of producing the high-quality water used to replace the bleed streams. Adjustment of the SX process, in particular use of multiple entrainment control steps, can provide significant reductions in the total bleed and make up requirements.

Jan 1, 2003

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By Williams M

Sheet flotation is a new two dimensional column flotation cell that produces continuous spectrum of products. Analogous to a shaking table in its performance and analysis, sheet flotation is a sheet of bubbles rising through packing contained between two walls. Feed enters the sheet at the lower left and the product exit along the top and right edges. Iligh grade materials exit at the top left, middlings exit at the top right comer and low grade waste materials exit at the bottom right. As in the case of a shaking table, two motions are required: up and right. Bubbles furnish the upwards movement for hydrophobic particles, slanted packing the rightward movement for hydrophilic particles. The sheet flotation cells is analysed as a 40 x 40 array of simple cells. In practice, 1000 x 1000 arrays of simple cells may be expected. With larger arrays, excellent separations may be expected. Because there is no recycle, there is no build-up of middlings in

Jan 1, 1993

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

The purposes of defining the mining environment for underground mass mining and the uses of characterisation data are outlined. The requirements for data in the areas of geology, surface and groundwater hydrology, topography and environmental constraints and geotechnical studies are identified. Emphasis is then placed on the collection and interpretation of geotechnical data for establishing the in situ stress regime and for rock mass characterisation. Methods used for diamond drilling, core logging, borehole logging, data analysis and presentation, rock mass modelling and rock mass classification are outlined. Finally, recent and potential advances in the state-of-the-art are identified in areas such as geophysical methods, measurement while drilling, computerised data collection and analysis, rock mass modelling, in situ stress measurement data presentation and interpretation, and some applications of rock mass characterisation data.

Jan 1, 2000

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By R Hindstr÷m

The demand for iron ore has increased dramatically in the last years and is forecast to remain on a stable high production level for years to come. ItÆs expected that the world economy is facing a stable continuous growth of iron ore to two billion tonnes and more over the next decades (Beddows, 2007). Furthermore it is expected that the existing and known high-grade ore resources will decline, and the iron ore industry will be forced to implement more and more advanced beneficiation plants. As a consequence of the more complex beneficiation requirements, there will be a need for modern solutions for iron ore dewatering that are reliable mechanically as well as cost effective and with high capacity per unit at the same time. Conventional vacuum filtration methods have been the most prevalent in fine iron ore dewatering. Product quality needs, lower ore grades, complex mineralogy and energy costs have resulted in iron ore producers seeking better solutions for dewatering, in particular pelletising feed. New advanced filtration methods have been introduced to the market. This paper describes how these modern methods are answering the needs of the industry. Performance of advanced dewatering technologies (pressure filtration and ceramic capillary action filtration) for iron ore applications has been studied, and the findings are based on both industrial and pilot scale experiences on different materials. For example, the results show that the cake moisture content of iron ore pelletising feed can be optimised more effectively by using modern filtration technologies. By selecting the most suitable and adjustable equipment, the effects of variations of feed material on downstream processes can be minimised and the possibilities of processing more difficult raw materials to high-quality pellets are better. The Larox Corporation develops, designs and manufactures industrial filters and is a leading technology company in its field. Larox is a full service solution provider in filtration for separating solids from liquids. As such, this paper compares the new developments in this market area with the prevailing known vacuum filtration technology, but focuses on a comparison between capillary action filters and rotary vacuum disc filters (RVDF). The trade name CeramecG is used to differentiate the Larox filter from the generic term.

Jan 1, 2007