Search Documents

The South Junction deposit of St Barbara Mines Limited was discovered in 1989 by the geologists of Ross Atkins Mining.The deposit occurs in the lower part of the Gabanintha Formation of the Lukes Creek Group in the Mt Magnet -Meekatharra greenstone belt. Country rock is predominantly talc-chlorite schist. Gold mineralisation is associated with north-south shear zones, quartz-carbonate-fuchsite alteration of the ultramafic rocks and in particular close to deeply weathered quartz-albite porphyry. For a detailed description of the geology of the South Junction Deposit see Fiala (1992).

Jan 1, 1993

A new least-squares method for inversion of d.c. resistivity soundings from horizontally layered earth is proposed. Powers are used as measured data. Apparent resistivity is generalized and apparent parameters curves are defined. Estimates for parameter errors are often possible even when data errors are unknown or large. Acceptance or rejection of a model is made an easier decision. Total computational effort is often reduced when compared to global least-squares methods, because although several optimizations are needed, few data points are involved in each, and initial guesses are requested only once and not all at the same time. Correlations between parameters may be used to improve solutions. Precise indications for extra needed data points can be conveyed. A test example is worked out and a field sounding, taken by Rijo (1973, personal communication) in an alluvium-filled river valley in north-eastern Brazil, is studied.

Jan 1, 1987

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

A review is given of progress made to- wards the development of personal gravimetric dust sampling for risk assessment on South African gold mines. The present strategy is critically examined on the basis of principles for assessing health hazard from dust exposure. Reasons are advanced for replacing the konimeter with a gravimetric system based on full shift personal sampling. Constraints imposed by local characteristics of gold mines are used to illustrate the difficulty in finding suitable instrumentation for measuring personal exposure to respirable silica.

Jan 1, 1988

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison's flowsheet will be Discussed.

Jan 1, 1991

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993

By Larsen D. F

Minor iron formation related base metal sulphide mineralization occurs in granulite facies metamorphic rocks of the early Proterozoic Willyama Complex. Rock sequences hosting three iron formation related Cu, Zn, Pb prospects from the Thackaringa Group (Suite 3) are described. A caparison of host rock sequences, style of mineralization and facies of iron formations suggests major differences in terms of the overall depositional environment. However, significant similarities are present with respect to the nature and distribution of iron formation facies and the occurrence of chlorite 'alteration' zones in close proximity to mineralization in all cases. The chlorite within these zones occurs in a number of diverse forms in a range of rock types. A comparison of the prospects shows that there is no evidence to indicate that the chlorite in the zones is a retrograde alteration product of former higher grade prograde mineralogies - the chlorite appears to have survived granulite facies metamorphism. The mode of occurence of the chlorite in the 'alteration' zones together with the fact that the association quartz + chlorite + magnetite + pyrite + base metals is cx rmn to all areas suggests that the chlorite is specifically related to the processes which deposited the stratiform iron formations and related sulphides. It is considered that the chlorite precursor was a prenetanorphic alteration product or chemical sediment closely related to submarine hot spring activity which was also the source for chemical sediment precursors of the iron formations, associated lode rocks and Sulphides.

Jan 1, 1983

By Burford B. D, Johnson N. W, Rohner P

Under design philosophy, the Hilton concentrator produced lead, zinc and LGM (lead plus zinc) concentrates. The LGM (Iow grade middling) concentrate was produced by combining coarse middling streams from the lead and zinc circuits, regrinding and subsequent flotation. Mineralogical examination of the zinc circuit middling stream prior to regrinding suggested that production of zinc concentrate from the zinc circuit middling stream should be possible by rearranging existing plant equipment. Laboratory testing of samples of plant products, however, showed that regrinding combined wi th the usual reagent suite was nO1 sufficient to produce a zinc concentrate of the required specifications.Examination of the process water highlighted a problem with dissolved salts in the circuit water, which was solved by in-circuit precipitation of the dissolved ions with soda ash. Implementation of the procedure in the concentrator effectively transferred to the zinc concentrate all sphalerite previously recovered to the LGM concentrate.

Jan 1, 1994

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998

By Weller KR

A study of high pressure rolls grinding of a number of Australian ores and minerals has been carried out using a pilot-scale machine with rolls 300 mm diameter and 70 mm wide. The results from this study have been used in conjunction with plant survey data to construct computer simulation models of various comminution circuits and these have been used to investigate options for incorporating high pressure grinding rolls into these comminution circuits. Possible rolls options for three of these circuits are presented, and likely energy savings over the existing circuits are discussed together with potential improvements in plant throughput and/or product sizing. A scale-up procedure for predicting full-scale machine performance from small-scale testing is described, and the effects of rolls operating conditions are also discussed.

Jan 1, 1991

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

Western Mining Corporation has grown from a small gold exploration and mining company, funded by large established mining companies, into a large multi-commodity and multi-national mining company with shareholders who no longer have the same understanding of mining as the founders. Ore reserve calculation methods and reporting procedures have gradually changed throughout the group during this growth. These changes have been led by the newer mines, in particular the Kambalda nickel mines, where the need for more global, less conservative reserves were required to justify capital and forward sales contracts and to inform shareholders of the true worth of their company. This change in attitude to reserves has flowed back to the gold mines and has allowed a better informed management and investing public to plan for the future. Management of the calculation of reserves remains the responsibility of individual mining operations, but a corporate reporting and management structure exists through the office of the Director of Exploration and divisional chief geologists who strive to maintain standards of calculation and reporting. Specialist ore reserve geologists are starting to justify their place in the organisation, particularly at the larger operations. Reporting to the new AusIMM Standards is fully supported, although the amount of supplementary information requested will need to be considered carefully because of the large number of factors that make up even the simplest reserve.

Jan 1, 1990

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

With the sinking of the No. 3 Shaft and the erection of a changehouse nearby, a sub-brace level structure was provided incorporating a time office, underground foremenÆs office and lamp room, in conjunction with a covered walkway, ambulance room, fire station and waiting brace.

Jan 1, 1957

By Aspinall T. O, Just G. D

Computer software systems have been developed to assist in a wide range of specific mine planning and scheduling applications. In selecting appropriate systems for any mining operation it is apparent that certain features have particular advantages for each mine site. The ideal solution to this problem is to select a range of systems which best relate to sections of each mining operation. This approach raises potential data linking difficulties where output from one system is incompatible with input requirements for other systems. A study at the University of Queensland investigated the problems related to the integration of a number of mine planning and scheduling software systems. The project used data from large scale coal strip mining operations in Central Queensland. Two major computer packages used extensively in the study were the SURPAC mine planning and XPAC mine scheduling systems. Dragline and truck and shovel operations were analysed in the project. Results of the work have been directly applied at the mine site to assist current strip design by effectively automating the design procedure. This enabled sensitivity studies to determine the effects of changing dragline working levels and varying pit dimensions. Coal blending studies and procedures to optimise operations have been investigated using linear programming within a spreadsheet software application. Output from the SURPAC and XPAC programs was directly linked to the linear program for this analysis. The simulation program GPSS/PC was also used in a similar manner to assess optimisation parameters.

Jan 1, 1992

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

By Plumridge C. L, Lynch J. E, Forresty R. J

The Amanda Bel Goldfield (new name) is an area of approximately 1000 sq. km centred 65km WSW of Ingham and 150km due east of Kidston (Camel Creek homestead to Ryeburn homestead area). Gold mineralisation has been located in tightly folded sediments of the Silurian Greenvale Formation as well as in the Early Devonian Kangaroo Hills Formation and the Early Carboniferous Clarke River Formation. The area is traversed by a major NW-SE structural corridor, with many of the numerous basaltic, andesitic and rhyolitic dykes of the region sharing a similar trend. So far fourteen gold-bearing zones have been located, all of which are new discoveries delineated by bulk cyanide leach sampling and subsequent geological reconnaissance. The region has undergone three periods of deformation with gold mineralisation introduced syn-D1, post D1 - pre D , syn-D and post-D2/D , thereby revealing an involved metall~genic history. Mineralisation types include Sb, Sb-Au, Sb-Au-As, Sb-Au-As (-Pb-Zn) and Au-As. Minor occurrences of W, Pb-Zn-Ag and Pb-Zn-Ag-As-Sn are also present as are alluvial (deep lead) tin Drosoects.

Jan 1, 1989

Probabilistic seismic hazard analyses (PSHA) have now gained wide acceptance in the development of design criteria for major projects. When used with regional criteria the procedures have also allowed the preparation of more rational seismic zoning maps. Seismic zoning maps using various levels of results from PSHA studies around the Pacific Rim now include Canada, Indonesia, New Zealand and the United States. Some Pacific Rim countries such as Chile where the seismic exposure is dominated by subduction events have no subdivision into separate zones.Approaches to risk based zoning are being considered in several Pacific Rim countries including Australia. Australian studies must face problems similar to parts of the Eastern United States where seismic activity is low with irregular and infrequent occurrences of moderately large earthquakes. The perception of the seismic exposure by both regulatory agencies and the public at large is different when considering areas of low seismicity. There is therefore a need to make different interpretations of the results of PSHA studies in these areas of low seismicity. The aim of this paper is to explore some of these differences by comparing the results from two site specific studies from areas with widely differing seismic activity rates.

Jan 1, 1990

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990