Search Documents

By Lemberg D. W, Friday R. G

Potential means of lowering overall costs to permit deeper stripping include : 1. the use of larger diameter blastholes in highly-fissured strata (to reduce drilling costs); 2. dewatering from semi-permanent bores to reduce blasting costs (by maximising the use of bulk ANFO) and promote highwall stability; and 3. the use of inclined blastholes, bulk AN, staggered V1 patterns, adequate backfill and more cost-effective stemming columns. Each of these is covered. The pumping of bulk watergels continuously raises the blasthole water column, thereby perpetuating the demand for these blasting agents. This must be a principal consideration when choosing between a bulk and a packaged watergel. Any packaged product should exhibit dimensional permanence and an energy yield per metre length equal to that of bulk ANFO. Possible ways in which controlled trajectory blasting (CTB) could benefit deeper stripping operations are outlined. By allowing the maximum use of bulk ANFO, de- watering may be a prerequisite of a viable CTB Operation.

Jan 1, 1981

By Dorricott M. G

Ballarat Goldfields NL is developing an exploration decline at Ballarat East using a Mitsui Miike S-125 roadheader. To-date, 530 in of advance has been achieved at an average rate of 16.1 m/week. Roadheader availability has averaged 94.3 per cent, and pick consumption has averaged 0.016 per m. Ground support has involved pattern rockbolting with split sets, 100 mm thick fibre reinforced shotcrete, and steel sets as required. The slower than expected advance rate has mainly been due to difficult ground conditions. It is expected that a further 970 in of decline will be mechanically excavated before a drill and blast system becomes more economical.

Jan 1, 1995

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

In April, 1990 the Sydney Water Board invited bids for the construction of the Hazelbrook Carrier Section 3 being part of the Blue Mountains Sewerage Transfer Scheme. In December 1990 the contract was awarded to Costain Resources Limited, Mining Services Division for the sum of $A15.3 M. The works consisted of excavation of 9 520 linear metres of tunnel, 3.35 metres diameter with installation of permanent ground support in the form of rockbolts, mesh, steel sets, shotcrete and in situ concrete

Jan 1, 1993

Nauru Phosphate, which is one of the world's highest grade deposits discovered to date, contributed in 1969, 2.2 million tons of the total world production of 77.7 million tons. Phosphate production, which is the major source of revenue for the island nation, is carried out by the Nauru Phosphate Corporation, headed by a Government appointed Board of Directors. The complete mining operation, including ship loading techniques, is discussed along with proposals at present being investigated to upgrade the Quality of the product.

Jan 1, 1971

By Newell RB

Grinding circuits are used in most mineral processing plants. Their widespread application makes the efficient running of the circuits essential to almost all resource projects. This paper will show that, with the application of modern multivariable control techniques, improved plant performance can be obtained when compared with conventional single loop control strategies. Results are presented for a simulated closed-circuit ball mill.The grinding circuit was controlled using the rod-mill water and primary and secondary sump dilution flowrates as the manipulated variables. Variables controlled were the primary cyclone feed flowrate, the primary cyclone feed density and the particle-size measurement (percentage smaller than 75 um).

Jan 1, 1985

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

At 11 p.m. on Tuesday, 24th July 1979, an explosion of methane gas in a three heading development panel at Appin Colliery resulted in the deaths of fourteen men. The explosion followed after or was asso- ciated with a changeover of the ventilation to achieve a central intake between two returns. Investigation by Inspectors was followed by separate Judicial and Coronial Inquiries. Investigational information aimed at understanding the circumstances of the ex- plosion was prepared for the Inquiries. Recommendations following the Judicial Inquiry have been adopted by the Department of Mineral Resources.

Jan 1, 1981

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

Rock bolting has become the most important method of ground support at Mount Isa. Various types of rock bolts are used to suit the different applications and requirements. To apply rock bolting techniques satisfactorily, it is necessary to have some knowledge of the nature of the rock, the type of rock failure, any stress redistribution which may occur during the intended life of the rock bolt and the time for which ground support is required. At Mount Isa there are a number of dif- ferent applications of rock bolts for ground support, and some trends in rock bolting techniques.

Jan 1, 1971

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

The concentrating plant of the Broken Hill South Limited was described in Proceedings No. 44, Australasian Institute Mining and Metallurgy, December, 1921, by Wainwright and Read. It was erected on the present site in 1907 and 1908.From that date, the plant has undergone various alterations consistent with metallurgical improvements. By 1925, the timber work of the gravity secti"on had seriously deteriorated, so much so, that, when the machinery was working, the floors and supports vibrated badly, causing heavy maintenance costs.In 1928, it was decided to erect a new gravity-treatment section, to be followed later by a new flotation section.

Jan 1, 1932

By Hodges D. A

The manufacture of steel from raw materials which have to be mined, transported and processed must affect the environment. Steelmaking, like almost every other stage of manufacture involves the unwanted production of dust and fume; thus a major part of the steel industry's effort to minimize changes to the environment is the collection, treatment and recycling of dust and fume to avoid pollution of the atmosphere and waterways. The paper describes how this achieved in the various steelmaking processes and shows the diversity of problems-and their solutions in this context. Particular emphasis is, given to basic oxygen steelmaking.

Jan 1, 1976

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI' and associated axjal plane cleavage SI' and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2'), a northeast trending crenulation cleavage (52'), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2'). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1', also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1', as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

SINCE 1900, five underground fires of consequence have beenrecorded in the Broken Hill mines. These occurred at the Junction(1906), Proprietary (1906 and 1916), Block 14 (1906), and Centralmines (1923). All have been extinguished, but at an enormouscost; e.g., in the eleven months following on the 1923 Central mine fire the sum of £187,123 was expended in fire-fighting operations.To this series may be added others, as the South (1925) and British mine (1918) fires, which were extinguished before serious damage had resulted. All, however, have occurred within a period of 28 years, and in a district where spontaneous combustion, a prolific source of fire in the U.S.A., has been practically nonexistent. Therefore, definite fire risks exist in the underground workings of the Broken Hill mines, and, as a consequence, an active fire prevention policy is a necessity...

Jan 1, 1929