Search Documents

By Richards JR, Herbert HK

A basic question in preparing this review was how to define sulphur mineral occurrences as being associated with the Pacific Rim. This question will be reconsidered later. The isotope composition of sulphur- containing minerals may be considered in terms of two primary sources - 1. deep- seated sulphur, devoid of crustal contam- ination with a 634S value near 00/0o and 2. oceanic sulphate which fluctuated in value between +10 and +300/00 over geological time (Claypool et al., 1980). However, minerals have seldom been directly derived from these primary sources as even evaporites have been dissolved and reprecipitated. The marine source is differentiated biochemically and isotopically in recent sediments where sulphide from bacterial sulphate reduction may be significantly depleted in 31S. The question of chemical interaction of ascend- ing magma with upper crustal rocks has become one of degree rather than whether or not it occurs. Mineral deposition is considered increasingly in terms of mixing of fluids and their chemical reactions with rocks rather than direct precipitation from magmas or hydrothermal fluids derived from them.

Jan 1, 1987

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By W Wu

The prospect of discrete element modelling (DEM) being used as an everyday design tool for transfer chutes in the iron ore mining industry is becoming more and more probable. However, much care needs to be taken to ensure accurate results are obtained. Whilst there are many publications in industry portraying the potential of DEM, there is little evidence of where it has been validated against a real set of experimental results. The purpose of this investigation was to gauge whether the incorporation of the physical properties of a specific bulk material at the DEM pre-processing stage can yield visually and numerically accurate simulations for a simple flow case. Effects such as irregular particle shapes, varying frictional properties and coefficients of restitution, all found through experimentation were investigated. Video analysis was used to compare simulations to real flow cases. It was found the most critical attributes in determining the accuracy of the simulations were particle shape and wall friction. Keeping the particle-to-wall friction factor constant was not sufficient to describe the flow accurately. But by introducing the varying effects of wall friction with consolidation stress, the correct results were simulated.

Jan 1, 2007

All large open pits in Australia have been mined, or are planned to be mined well below the local water table. This raises several issues that impact on mine safety, mining costs and regulatory approvals. Some pits will be æwetÆ, where they are mined through permeable horizons and where there will be measurable groundwater inflows. These will require some form of dewatering. There may also be some difficulties in the disposal of excess water. Other pits, may be ædryÆ, where they are mined through impermeable material and there are no measurable groundwater inflows but where there are stability issues related to hydrostatic pressures within the pit walls. These may require some form of depressurisation. Some pits are a combination of both. Effective management of groundwater inflows and groundwater related stability issues and the development of cost effective and environmentally acceptable dewatering and depressurisation systems requires an understanding of site specific hydrogeological conditions and practical experience in what works best for different conditions. The presentation will include an outline of the key hydrogeological factors that impact on large pits, practical methodologies for achieving dewatering/ depressurisation, and some case studies from the Goldfields, Pilbara and North Queensland.

Jan 1, 2003

Separating Particles by Horizontal Deflection in a Paramagnetic Fluid This paper describes the horizontal deflection behavior of particles in paramagnetic fluids under a high-gradient superconducting magnetic field. Movements of single particle were observed experimentally and indicated that they could be deflected to different positions. Based on these results, the behavior of groups of particles from ore samples was examined in the superconducting magnetic. It was found that these particles could be deflected and settled at a certain position due to the combination of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different susceptibilities and/or densities could be deflected to different positions, thus producing groupings of similar types of particles. The work described here, although in its infancy, could form the basis of new approach to separating particles based on a combination of susceptibility and density.  

Sep 13, 2010

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

About 20 percent of world gold production has been contributed by gold deposits in Archaean greenstone belts, of which ca 2100 tonnes of gold has been produced from Archaean greenstone belts in Western Australia (Phillips, in press). These deposits are, therefore, important exploration targets and an under-standing of their nature and genesis can help to formulate exploration strategies and delineate potential targets.A literature survey of Archaean granitoid-greenstone terrains indicates that a wide variety of lithologies host gold deposits. The major part of production from the Yilgarn Block, Western Australia, has come from mafic volcanics andintrusives (70% of production),with significant contributions from BIF-hosted ores (15%) and low production from sediments, felsic volcanics, porphyry intrusives and granitoids (Groves et al., in press). Similarly, most

Jan 1, 1984

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978

By Parks T. C

A low-grade disseminated nickel sulphide serpentinite ore from W.A. had a relatively high permeability after drying. Various techniques indicated that the permeability resided within a fine network of fibrous vein- lets and especially within coarse cracks along which the sulphides lay. The ore minerals were therefore open to selective extraction by chemical leaching. A IM ammonia-7.8 wt.o "ammonium carbonate" solution, oxygenated at 1 bar oxygen pressure and about 23¦C, released nickel, copper and cobalt from the sulphides, leaving a permeable residue of goethite, while calcium, magnesium and iron concentrations remained negligible in the leachant. The nickel and copper was electrodeposited directly from the pregnant liquor in a deposit which included 16.5 wt.% sulphur. Enhanced copper/ nickel ratios early in the extraction suggested that valleriite (not amenable to flotation) was leached preferentially. Th$ controlling influence of the pore structure was demonstrated by the dependence of leaching rates on the size of the ore particles used, and on the measured porosity of different ore samples. A 2mm size was probably the optimum for exposing sulphides to the leachant. Leaching was accelerated by increasing the temperature and oxygen pressure.

Jan 1, 1974

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By K Dagdelen

A vehicle proximity warning system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two an a half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH funded project and discusses the GPS accuracy tests and overall system tests that were carried out during 2001 at the Morenci open pit copper mine in Arizona.

Jan 1, 2003

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980

By Hayba DO

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modeling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

By P Worsey, B Lane

The recommended maximum explosive weight for boulder blasting using internal charges is 0.15 kg/m 3 (Olofsson, 1988). Normally this charge results in excessive scattering and flyrock, creating increased liability for the operator, especially in congested areas. An alternative technique using smaller explosive charges is being developed at the University of Missouri-Rolla (UMR). It is designed to reduce boulder scatter, flyrock and fumes and allows shooting in close proximity, using common blasting products. The method comprises drilling a hole into the top of the boulder, inserting a small primer, filling the hole with water and shooting it. The hole is drilled approximately two thirds into the boulder and the charge (10 g/m 3 ) is placed half way into the hole filled with water. Upon initiation the primer produces a small volume of gas at extremely high pressure which acts upon the surrounding (relatively incompressible) water. The water transmits this pressure to the surrounding blasthole, hydraulically fracturing the rock. As the fractures propagate and the boulder expands a rapid increase in the blasthole volume occurs. Because of the small charge the gas pressure quickly dissipates reducing rock movement, resulting in a fractured boulder with minimal material leaving the immediate vicinity. The current work includes both laboratory and field testing programs. The laboratory program is focussed on determining optimum parameters at reduced scale using concrete cubes. The field program focuses on determining a minimum powder factor and includes shooting smaller boulders up to 1 m 3 underground and 1.5 to 5 m 3 boulders in a surface quarry. In both cases the boulders were obtained as oversize from regular production blasts.

Jan 1, 1999

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By Montini A

The dynamic behaviour of the load in a pilot-scale ball mill has been measured as a function of axial position within the mill, end plate lifter design, load volume J (percent of mill volume), percent solids in the slurry S and mill speed N (percent of critical speed). Conductivity probes were inserted through the shell of the mill to provide online measurements of the dynamic orientation of the load in the mill. It was found that 1. the height of the shoulder of the load is increased by increasing J, S or N. 2. Measurements of the effect of S on the location of the shoulder of the load should be very useful in mill control strategies. 3. The axial centre of gravity of the load in the mill is not affected by operating conditions. 4. The presence of lifters on the feed end plate does not affect the torque drawn by the mill. 5. Holdup of slurry in the mill is a strong function of slurry viscosity and a weak function of mill speed.

Jan 1, 1986

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005