Search Documents

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By Wilson AF

Gold-silver mineralization at Cracow and Ukalunda in Queensland comprise quartz-filled veins, fissures and breccia zones hosted by propylitically altered volcanics and epizonal intrusions which are strongly fractured. The terrestrial volcanic facies, structural setting, type of alteration and complex mineralogy suggest these deposits are of the epithermal type.The 180 depleted character of the wall-rocks is consistent with the involvement of meteoric waters in convective hydrothermal cells associated with the vulcanism. The Cracow quartzes have remarkably low 6180 values from -2.0 to -3.4 per mil typical. of meteoric hydrothermal systems at high latitude, consistent with the inferred position of Australia during the Permian. 6180 values for the Ukalunda quartzes exhibit a wide range from 5.1 to 14.9 per mil which reflect the mixing of magmatic and meteoric waters, and a steep geothermal gradient.Further stable isotope and geochemical studies are in progress to establish the scale and morphology of the zones of anomalous 6180 and mineralogy in the wallrocks which constitute significant exploration targets.

Jan 1, 1984

By A Bagis, T Baker

In 1983 the New South Wales (NSW) Government began to construct a 35 km freight rail line to provide additional rail capacity to Port Kembla in the Illawarra region, south of Sydney, through a direct connection between the Unanderra to Moss Vale line at Dombarton to the Main South rail line at Maldon in the Southern Highlands. The project area lies within the carefully managed Sydney Water catchment and is also underlain by previous coal mining activities.Construction of the line halted in 1988 prior to its completion after the NSW Government reassessed the demand case and found that the project was not as viable as originally forecast. However, by this stage the line was partially constructed, including the majority of civil earthworks, approach structures to the main river crossings and establishing the portals for the Avon tunnel as a precursor to major tunnelling works.In 2012, the Commonwealth Government funded Transport for NSW to undertake the necessary engineering and environmental preconstruction works. Most importantly here, the 1980s rail link was predicated upon the use of electrically powered locomotives, whereas the locomotive fleet in operation today in NSW is diesel powered. This fact has a significant impact upon the approach and development of the Avon tunnel section, as the diesel powered locomotives combined with the length and grade of the tunnel alignment produces a unique set of conditions requiring specialist engineering design and systems to ensure safe and functional operation of the railway through the tunnel section.Given the above, the Avon tunnel will need to be supported by a ventilation and smoke control design based on the heat rejection from the locomotive consist, consideration of ambient air quality compliance, comparison against in-tunnel air quality goals, and providing safety systems in line with the fire and life safety strategy it requires.This paper explores the current development of both the tunnel civil works responding to the geography, geology, rail functional requirements, as well as the tunnel ventilation systems being revised to suit the diesel locomotives.Further, this paper describes the importance of combining the design outcomes with the procurement methodology in order to achieve the project objectives, a functional outcome and value for money across the project life.CITATION:Baker, T and Bagis, A, 2014. Maldon to Dombarton Rail Link – design development of the Avon Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J McCluskey, N Barros

"Long-term strategic planning at BHP Billiton’s Western Australia Iron Ore business aims for sustainable value maximisation of its large, long-life, low-cost, expandable mineral inventory and supply chain infrastructure. While mine plans are key components of this value equation, this objective requires a whole-of-business approach through comprehensive consideration and optimisation of the full value chain. Only through a system view do we believe that the value proposition of a set of plans is truly optimised.The fundamental considerations include: mineral inventory information, given its intrinsic uncertainty and risk/knowledge horizon a marketing view of future quality premium/discount based on overall market quality load whole of supply chain optimisation on a throughput accounting basis alternative sequences of capital decisions closure costs with significant magnitude of total movement requiring optimisation as part of the plan. In addition, the plan provides a view of acceptable uncertainty levels at different times in the future.BHP Billiton Iron Ore uses a structured Life of Asset planning process that supports the business with the optimisation of its maximum value proposition through a non-deterministic scenario-based optimisation approach on an annual basis. This is a key input to each year’s medium-term plans and budgets, including activities identified through a value of information approach that resolve the key uncertainties and steadily improve confidence in the plan.CITATION:McCluskey, J and Barros, N, 2014. Life of asset planning, uncertainty and value optimisation of the iron ore business – from exploration, to market, to closure, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By C Paoletti

About 15 years ago the debate on the reliability of sampling procedures for agricultural food and feed commodities was initiated by a few brave scientists who questioned the representativeness of what, at the time, were routine sampling procedures established exclusively on the basis of tradition and practical feasibility. Over time several national and international organisations contributed to the discussion, developing standards and publishing papers either to underline the fact that sampling is always a source of error, in itself, which cannot be overlooked, or to minimise the relevance of sampling on the basis of argumentations linked to time and money limitations. The latter dominated, but is nevertheless impossible to accept from both a scientific and a responsible management perspective. Here the author presents an historical overview of these past 15 years, illustrating the most controversial issues, reporting major achievements in food/feed sampling, highlighting milestones, as well as unresolved problems that still need the attention and contribution from the sampling community. The need to incorporate Theory of Sampling (TOS) into food/feed safety assessment (pre-market), as well as into food/feed safety monitoring (post-market) has recently been highlighted, and the practical applicability of TOS to base food/feed safety decisions on representative sampling, has been explored and documented via concrete examples of risk analysis in different areas of food/feed industrial production chains. Now it is time to move forward and ensure that TOS is fully integrated into the well-established Food and Agriculture Organization (FAO) / World Health Organization (WHO) risk assessment approach, in order to guarantee a transparent and correct universal frame for risk assessment and the subsequent management decision-making process. WCSB8 offers the ideal platform to explore the best way to do so, switching from a theoretical discussion of correct sampling principles for food and feed agricultural commodities to practical recommendations in the interest of consumers, worldwide. These 15 years have also been a personal journey of interesting dimensions, indeed a veritable roller-coaster ride in-and-out of the scientific, technological, industrial and (last but not least) regulatory worlds. The start was WCSB2 in 2004, when I flew to Australia to discover if in other areas sampling had been identified as an unavoidable issue and, if so, what the solution was. There, I found a good travel companion who today is still on my side, to assemble the puzzle and explore how to shape the future, to concretely answer to the 15 years’ quest for proper sampling in the assessment and monitoring of food/feed safety.CITATION:Paoletti, C, 2017. Assessing and monitoring food and feed safety – a 15 year quest for proper sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 39–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R Burke, G Ramage, C Donnelly

Over the decades, Redpath has undertaken a multitude of tunnelling and underground excavation projects for civil and mining clients both domestically and internationally. These projects have been undertaken through varying strata conditions with differing excavation methods in remote locations and in central business districts.With the recent turbulent nature of the global financial environment, project drivers have been challenged with the emphasis being placed on methods to gain early access to orebodies, rapid development techniques, lower capital costs and reduced labour requirements to name a few.A number of mining companies seeking to achieve these objectives have commenced the journey to better understand the operational constraints, challenges and opportunities that may be available with the use of alternative excavation methods.The development of safe and effective alternative excavation methods that comply with both domestic and international mining legislation and regulatory requirements is a challenge the industry needs to embrace. Given the current cost pressures being faced by the Australian mining industry, some alternative excavation methods offer the potential for longer term sustainability and rapid development of resources.More recently work has been undertaken on a project that challenged the norm and implemented an alternative excavation method with the use of an excavator with a rotating drum cutter head.This paper will review this recent project and provide technical and operational insight into some of the challenges faced in implementing an alternative excavation method in the metalliferous industry.CITATION:Donnelly, C, Ramage, G and Burke, R, 2014. Challenging the norm – alternative excavation method in mining, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 187–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By C Fong

Compliance Planning is an active approach to ensure mining operations align more closely to their longer-term plans. Through Compliance Planning, operations can not only measure their performance on intervals as short as intra-shift, but they can then apply corrective measures to ensure they remain as close as possible to the plans. Compliance Planning targets short-term and execution level teams, as these are the shortest duration planning divisions commonly found in mining operations. Compliance Planning combines live information with intelligent planning capabilities to provide a framework that enables mining operations to realise a significant improvement in reconciliation of plan to actual movements.

Jun 22, 2022

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By D J Maconochie

The use of rock bolts as permanent support has been prohibited by client specifications in several recent large tunnel projects in Australia. The justification for this appears to lie in concerns with proper and verifiable installation procedures rather than concerns with the intrinsic durability of the corrosion protection systems. However, in civil tunnels, preventing the use of permanent rock bolts for long-term support results in the use of cast in place concrete lining which in some instances would otherwise be unnecessary.

Mar 8, 2011

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By N Belluz, L Johnson, N Wiwoho, P Manning

The Kucing Liar skarn deposit is located in the Ertsberg mining district, which also contains other skarn deposits and the Grasberg porphyry copper û gold deposit. The Ertsberg district is located in the province of Irian Jaya, IndonesiaÆs easternmost province. Mining development began in the Ertsberg district in 1972 with the mining of the Ertsberg deposit. Daily production in the district now averages about 230 000 tonnes of ore, with the bulk of the ore coming from the Grasberg open pit and the balance from underground mining of skarn deposits. During 1998, 45 218 additional metres of drilling were conducted to delineate and understand the Kucing Liar orebody. The deposit was first intersected in drill holes in 1994 and then was intersected in underground workings located about 1000 metres from the discovery drill hole in 1995. Initially, the two intersections were thought to be different orebodies but are now realised to be different parts of the same orebody. The Kucing Liar deposit consists of magnetite û copper û gold replacement and skarn mineralisation in favorable Tertiary and Cretaceous units. The deposit is approximately 2000 metres in length and averages about 200 to 250 metres in thickness. The width varies from 400 to 600 metres. Drilling in 1998 was directed towards delineating the deposit on its NW and SE ends and to determine its down dip extension. Reserves for the deposit at the end of 1998 stand at 320 million tonnes at 1.4 per cent copper, 1.4 g/t gold, and 5.3 g/t silver. Many important questions remain to be answered concerning the relationship of the Kucing Liar orebody to the major faults in the district and to the Grasberg intrusive complex which contains the Grasberg orebody. Continued exciting developments are anticipated as work to understand the deposit by drilling and geologic study continues.

Jan 1, 1999

By K Rau

The overall success of a mining operation is directly impacted by the reliability and availability of mining equipment. Heavy-duty vehicles such as excavators and haul trucks are used for conveying of bulk material and improving such assets’ availability helps reduce costs, increase throughputs and improve safety (Ravande, 2022). If a mining operation’s key performance indicators (KPIs) are tied to operational performance, then overall equipment effectiveness (OEE) is an essential metric to track progress and to identify areas of improvement.

Sep 1, 2024

By J Andrina, D Richar, R Smart, A Neale

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. From 2003 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A major focus of the investigations is developing strategies to maximise the beneficial use of the limestone that will be mined. Laboratory columns and field test pad investigations have been ongoing for six years examining limestone blends. Trial dumps utilising truck placement and conveyor/stacker placement and blending of limestone and acid generating rock have recently been constructed. In addition, based on initial results, investigations aimed at further evaluating the performance of limestone covers in this high rainfall environment have commenced. A significant finding has been the identification of strong armouring layers on sulfide surfaces within well-blended material and under limestone covers. These layers effectively isolate sulfides and thus progressively slow the oxidation rate to a level where the alkalinity load from the limestone exceeds the rate of acid generating. ARD is controlled and neutral low metal drainage results. The results have demonstrated that although limestone blending is effective, it is necessary to ensure that all size fractions within the blend receive adequate acid neutralising capacity to buffer the potential acidity. Because the sulfur content generally increases and the acid neutralising capacity decreases with decreasing particle size in limestone blends, the amount of limestone required greatly exceeds the stoichiometric requirement. This paper describes the development of limestone blending specifications for potentially acid forming overburden and presents the results of the ongoing limestone cover trials at the Grasberg mine.

Jan 1, 2003

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By D Brereton, C J. Moran

Intensive resource extraction, in the form of multiple mining operations, presents significant assessment and management challenges for resource developers, governments, community and the environment. Cumulative impacts, ie the successive, incremental and combined impacts (both positive and negative) of an activity on society, the economy and the environment, can place significant pressure on social, economic and environmental capital and render conventional mine-by-mine approaches to management ineffective. Cumulative impacts can be what are most important to environments, communities and economies surrounded by multiple mining operations because cumulative impacts are what they experience. There is much to gain from increased consideration of cumulative impacts. Unmitigated impacts have the potential to delay or even prevent expansion of mining in existing and prospective areas. On the other hand proactive management of cumulative impacts can benefit regional environments and communities and contribute to the industryÆs social license to operate. Resources are often not the limiting factor to better cumulative impact management. More effective coordination of existing resources may go a long way toward mitigation and enhancement, and better planning and assessment may help avoid impacts and exploit opportunities for efficiency gains through reduced duplication. In this paper we draw from working examples to present five practical assessment and management strategies applicable to resource companies to enhance positive, and avoid and mitigate negative, cumulative impacts. The strategies are presented based on their capacity for achieving outcomes, ease of implementation and cost effectiveness and are drawn from a multi-year study on the assessment and management of cumulative impacts in the Hunter Valley, New South Wales and a follow-up study to improve cumulative impact assessment and management practice in the Australian coal mining industry, both reported elsewhere.  

Jan 1, 2009

By J-P Franzidis

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMCÆs (now BHP BillitonÆs) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

By M Wortley, J Korteniemi, D La Rosa, L Rajavuori

Geometallurgical modelling of an orebody provides benefits to a mine by gaining a better understanding of the ore characteristics and how they affect the performance of the concentrator. With this knowledge, plant operating conditions can be adjusted to optimise throughput and recovery in advance of the arrival of particular ore types. Therefore, it is extremely important that the origin of the ore being processed is known as accurately as possible. Depending on the homogeneity of the ore characteristics, reliance on assumptions about stockpile residence times, scheduling and material handling can render the best geometallurgical models useless.The solution adopted at Agnico Eagle’s Kittilä mine was to utilise Metso SmartTags™ and in-house expertise to develop a system that continuously and accurately links geotechnical and lab data from the mine to the performance of the plant. This application presented several unique opportunities and challenges. For example, this was the first installation of a SmartTag™ system for geometallurgical modelling in an underground mine. Challenges included the fact that the system installation is routinely subjected to temperatures below -20°C.The system was installed and commissioned in early 2013 and has been operating continuously since. Kittilä has begun to see the benefits of the system, with an increased understanding of how different ores are processed in the concentrator. Other advantages include the ability to alert operators about the arrival of difficult ores and a better understanding of the ore handling systems.This paper describes the installation and use of the system at Kittilä and details some of the geometallurgical relationships that have been developed using the data collected so far.CITATION:La Rosa, D, Rajavuori, L, Korteniemi, J and Wortley, M, 2014. Geometallurgical modelling and ore tracking at Kittilä Mine, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N Murthy

Alumina is a major impurity in Australian iron ores and as the higher grade ores become depleted there will be a stronger focus on treating lower grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the alumina content. High alumina in iron ore is deleterious in that it can:• produce slags with lower desulfurising capacity,• reduce sinter/pellet strength and quality, and• produce higher slag volume and increase slag viscosity.Meeting iron ore quality specifications for alumina by blending ore from different sources will eventually be insufficient. Hence, innovative flow sheets based on new and commercially available technologies will be required. Their advantages and disadvantages, the testing methodologies and the challenges and diffi culties involved in reducing the alumina content of iron ores are presented and discussed.

Jul 11, 2011